Panasonic PT-RCQ10 Operating Instructions Manual page 250

List of DisplayPort compatible signals
The following table specifies the DisplayPort signals that the projector can project. This is supported when the
optional Interface Board for DisplayPort 2 input (Model No.: ET-MDNDP10) is installed in the slot.
Signal with l in the plug and play compatible signal column is the signal described in the EDID (extended display
identification data) of the projector. For the signal without l in the plug and play compatible signal column, the
resolution may not be selected on the computer even if the projector is supporting it.
Signal name Resolution
(SIGNAL FORMAT) (Dots)
720/60p 1 280 x 720
720/50p 1 280 x 720
1080/24p 1 920 x 1 080
1080/25p 1 920 x 1 080
1080/30p 1 920 x 1 080
1080/60p 1 920 x 1 080
1080/50p 1 920 x 1 080
1080/120p 1 920 x 1 080
3840 x 2160/24p 3 840 x 2 160
3840 x 2160/25p 3 840 x 2 160
3840 x 2160/30p 3 840 x 2 160
3840 x 2160/60p 3 840 x 2 160
3840 x 2160/50p 3 840 x 2 160
4096 x 2160/24p 4 096 x 2 160
4096 x 2160/25p 4 096 x 2 160
4096 x 2160/30p 4 096 x 2 160
4096 x 2160/60p 4 096 x 2 160
4096 x 2160/50p 4 096 x 2 160
640 x 480/60 640 x 480
1024 x 768/50 1 024 x 768
1024 x 768/60 1 024 x 768
1280 x 800/50 1 280 x 800
1280 x 800/60 1 280 x 800
1400 x 1050/50 1 400 x 1 050
1400 x 1050/60 1 400 x 1 050
1600 x 900/50 1 600 x 900
1600 x 900/60 1 600 x 900
1600 x 1200/50 1 600 x 1 200
1600 x 1200/60 1 600 x 1 200
1920 x 1200/50 1 920 x 1 200
1920 x 1200/60RB 1 920 x 1 200
3840 x 2400/30 3 840 x 2 400
3840 x 2400/60 3 840 x 2 400
3840 x 2400/50 3 840 x 2 400
*1 The signal with 1/1.001x vertical scanning frequency is also supported.
*2 VESA CVT-RB (Reduced Blanking)-compliant
Note
f A signal with a different resolution is converted to the number of display dots. The number of display dots is as follows.
g When the [ADVANCED MENU] menu → [SMOOTH PIXEL DRIVE] is set to [ON]: 4 608 000 pixels (2 715 x 1 697)
g When the [ADVANCED MENU] menu → [SMOOTH PIXEL DRIVE] is set to [OFF]: 2 304 000 pixels (1 920 x 1 200)
f The setting in the [POSITION] menu → [GEOMETRY] is disabled when the image of 1080/120p is displayed, and the geometric adjustment
function cannot be used.
f If connecting the projector to a computer that uses an early-type chipset or graphics card compatible with DisplayPort, the projector or
computer may not be operated properly when the signal output from DisplayPort on the computer is input to the projector. In such a case,
switch off the projector or computer and then switch it on.
If the signal output from DisplayPort is input to the projector, use of the computer equipped with the latest chipset or graphics card is
recommended.
250 - ENGLISH
Chapter 7 Appendix — Technical information
Scanning
Dot clock
freq.
freq.
Horizontal Vertical
(MHz)
(kHz) (Hz)
45.0 60.0 74.3
*1
37.5 50.0 74.3
27.0 24.0 74.3
*1
28.1 25.0 74.3
33.8 30.0 74.3
*1
67.5 60.0 148.5
*1
56.3 50.0 148.5
135.0 120.0 297.0
*1
54.0 24.0 297.0
*1
56.3 25.0 297.0
67.5 30.0 297.0
*1
135.0 60.0 594.0
*1
112.5 50.0 594.0
54.0 24.0 297.0
*1
56.3 25.0 297.0
67.5 30.0 297.0
*1
135.0 60.0 594.0
*1
112.5 50.0 594.0
31.5 59.9 25.2
39.6 50.0 51.9
48.4 60.0 65.0
41.3 50.0 68.0
49.7 59.8 83.5
54.1 50.0 99.9
65.2 60.0 122.6
46.4 49.9 96.5
55.9 60.0 119.0
61.8 49.9 131.5
75.0 60.0 162.0
61.8 49.9 158.3
74.0 60.0 154.0
*2
73.0 30.0 286.2
*2
148.1 60.0 592.5
*2
122.9 50.0 481.6
*2
Plug and play compatible signal
4K/60p 4K/30p
l l
l l
l l
l l
l l
l l
l l
l l
l l
l l
l l
―
l
―
l
l l
l l
l l
―
l
―
l
l l
― ―
l l
― ―
― ―
― ―
l l
― ―
l l
― ―
l l
― ―
l l
― ―
― ―
― ―
2K
l
l
l
l
l
l
l
―
―
―
―
―
―
―
―
―
―
―
l
―
l
―
―
―
l
―
l
―
l
―
l
―
―
―