Panasonic PT-RCQ10 Operating Instructions Manual page 131

f The [SDI LINK] setting cannot be changed when the [DISPLAY OPTION] menu → [BACKUP INPUT SETTING] → [BACKUP INPUT MODE]
is set as the combination to use the SDI input of the Interface Board.
f When [SDI LINK] is set to [AUTO], use the same format for the signal to be input to the <SDI 1 IN>/<SDI 2 IN/1 OUT>/<SDI 3 IN>/<SDI 4
IN/3 OUT> terminals. If different format signal is input to even one terminal, currently displayed image may not be projected correctly.
f [SDI MAPPING] and [3G-SDI MAPPING] cannot be set when [SDI LINK] is set to [AUTO].
f The content set is displayed in [SDI LINK SETTINGS].
Setting [RESOLUTION] in [SLOT IN] (SDI input)
1) Press as to select [SLOT IN].
2) Press the <ENTER> button.
f The [SLOT IN] screen is displayed.
3) Press as to select [SINGLE LINK SETTING], [DUAL LINK SETTING], or [QUAD LINK SETTING], and
press the <ENTER> button.
f The [SINGLE LINK SETTING] screen, the [DUAL LINK SETTING] screen, or the [QUAD LINK SETTING]
screen is displayed.
f Proceed to Step 5) when [DUAL LINK SETTING] or [QUAD LINK SETTING] is selected.
4) Press as to select [SDI1], [SDI2], [SDI3], or [SDI4], and press the <ENTER> button.
f The [SINGLE LINK SETTING] screen for the selected item is displayed.
5) Press as to select [RESOLUTION], and press the <ENTER> button.
f The [RESOLUTION] screen is displayed.
6) Press as to select an item, and press the <ENTER> button.
f Select [AUTO], [1280x720p], [1920x1080i], [1920x1080p], [1920x1080sF], [2048x1080p], [3840x2160p], or
[4096x2160p] when SDI1 input or SDI3 input is selected for [SINGLE LINK SETTING].
f Select [AUTO], [1280x720p], [1920x1080i], [1920x1080p], [1920x1080sF], or [2048x1080p] when SDI2
input or SDI4 input is selected for [SINGLE LINK SETTING].
f Select [AUTO], [1920x1080p], [2048x1080p], [3840x2160p], or [4096x2160p] when [DUAL LINK SETTING]
is selected.
f Select [AUTO], [3840x2160p], or [4096x2160p] when [QUAD LINK SETTING] is selected.
Setting [SDI MAPPING] in [SLOT IN] (SDI input)
Set the mapping method for the SDI1 input and the SDI3 input.
1) Press as to select [SLOT IN].
2) Press the <ENTER> button.
f The [SLOT IN] screen is displayed.
3) Press as to select [SINGLE LINK SETTING] or [DUAL LINK SETTING], and press the <ENTER>
button.
f The [SINGLE LINK SETTING] screen or the [DUAL LINK SETTING] screen is displayed.
f Proceed to Step 5) when [DUAL LINK SETTING] is selected.
4) Press as to select [SDI1] or [SDI3], and press the <ENTER> button.
f The [SINGLE LINK SETTING] screen for the selected item is displayed.
5) Press as to select [SDI MAPPING].
6) Press qw to switch the item.
f The items will switch each time you press the button.
[AUTO]
[TYPE1/LEVEL A]
[TYPE2/LEVEL B]
Note
f This function does not operate when the HD-SDI signal is input.
f [SDI MAPPING] cannot be set when [SDI LINK] is set to [AUTO].
Chapter 4 Settings — [DISPLAY OPTION] menu
Automatically selects [TYPE1/LEVEL A] or [TYPE2/LEVEL B].
Fixes the mapping method to Type 1 or Level-A.
Fixes the mapping method to Type 2 or Level-B.
ENGLISH - 131