Download
Share
Print this page
Lockly SECURE PRO Installation Manual
  1. Manuals
  2. Brands
  3. Lockly Manuals
  4. Door locks
  5. SECURE PRO
  6. Installation manual

Lockly SECURE PRO Installation Manual

Deadbolt edition
Hide thumbs Also See for SECURE PRO:

Advertisement

Quick Links

Download this manual
SECURE PRO
INSTALLATION
GUIDE
DEADBOLT EDITION

Advertisement

loading

Related Manuals for Lockly SECURE PRO

Summary of Contents for Lockly SECURE PRO

  • Page 1 SECURE PRO INSTALLATION GUIDE DEADBOLT EDITION...
  • Page 2 Welcome! This guide will walk you through step-by-step how to install and get your Lockly Secure Pro up and running. Installation generally takes less than 30 minutes. If you have any questions please reference our online support at: Lockly.com/support or call (669) 500-8835 for help.
  • Page 3 Go to Lockly.com/installation to watch a video version of this installation guide. Download the BILT app in the Apple or Google Play store for step-by-step interactive 3-D walk-through installation instructions.
  • Page 5 Preparation To complete the installation you will need: Tape measure or ruler Phillips Screwdriver Flathead Screwdriver Prepare door: remove existing deadbolt or use provided template to bore new holes. 2-⅜" (60mm) 2-¾" (70mm) 1-⅜" (35mm) Cross-bore to 2" (50mm) 2-⅛" (54mm) 1"...
  • Page 6 Step 1 ADJUST DEADBOLT AND INSTALL Deadbolt slot must align to the center of the door hole. Adjust as shown if needed. 2-3/4" (70mm) or 2-3/8” (60mm) The deadbolt comes set to 2-3/4" (70mm). Adjust length to 2-3/8” (60mm) if necessary. (wear gloves to protect from possible pinching).
  • Page 7 Step 1 ADJUST DEADBOLT AND INSTALL continued Extend the deadbolt by inserting a flat-head Insert the deadbolt into door edge hole. screwdriver into the slot and turning clock- make sure that the right side is up and the wise. slot is in the vertical position. Secure with 2 screws.
  • Page 8 Step 2 INSTALLING EXTERIOR ASSEMBLY (B) Adhesive tape Check the exterior assembly (B) alignment to door hole and deadbolt before peeling off film on adhesive strips. Peel film from adhesive strips and make sure torque blade is in the vertical position with the deadbolt extended.
  • Page 9 Step 3 INSTALLING INTERIOR ASSEMBLY (F) 1: Check interior mounting plate (D) 2: Align and secure mounting plate with alignment to your door hole before adhesive strips. Guide connection cables securing with adhesive strips. through the hole and secure to the lower left notched hole.
  • Page 10 It also sends push notifications to your phone whenever your door opens and enables voice control with Amazon Alexa or Google assistant. Lockly Secure Pro comes with a pre-wired door sensors consisting of two parts: Part (P) - Wired Sensor...
  • Page 11 Step 4 PREPARING DOOR SENSORS FOR INSTALLATION continued When installing the door sensors, make sure the arrow on the wired sensor (P) aligns to the arrow of the sensor magnet (Q) as close as possible. 3/4" (20mm) 2-3/8" (60mm) Foam pad The sensors need to be as close to level as possible.
  • Page 12 Step 4 PREPARING DOOR SENSORS FOR INSTALLATION continued The interior assembly comes with the pre-in- For left swing doors, re-route the door stalled wired door sensor setup for a right sensor wire through the side channel. Pull swing doors with 2 ¾" (70mm) backset*. the foam pad then re-insert to secure the wire.
  • Page 13 Step 5 INSTALLING THE INTERIOR ASSEMBLY (F) Plug the cable coming through mounting plate (D) into the interior assembly (F) as shown. Tuck cable under eyelet hooks and route to the right on interior assembly (F). Plug into , match red side of plug with red on socket - insert tightly.
  • Page 14 Step 5 INSTALLING THE INTERIOR ASSEMBLY (F) continued Torque Blade Thumb turn shaft Align torque blade with thumb turn shaft, make sure both are in the vertical position. Before placing the interior Place the interior assembly Secure the interior assembly assembly onto the mounting against the mounting plate to mount platedoor with 2...
  • Page 15 Step 6 INSTALLING BATTERIES PRESS & HOLD 1: With door open and deadbolt fully extended, place ribbon inside compartment and insert 4 batteries (note correct -/+ polarity). 2: After all batteries are installed, PRESS and HOLD the program button for 10S. The lock will auto- matically start self-check (release program button once check starts).

  • Page 16: Installing Batteries

    Step 6 INSTALLING BATTERIES 3: Once self-check completes ensure the lock operates smoothly by manually locking and unlocking the door using the thumb turn on the interior assembly. The deadbolt should operate smoothly without any interference or binding. If necessary, repeat step 2 and ensure that (a) the deadbolt was extended and (b) the torque blade was inserted vertically while the deadbolt was extended.
  • Page 17 Step 7 INSTALLING THE DOORS SENSOR Make sure you have prepared the door sensors for installation, see step 4 LOCK SENSOR (P) Install on the interior side only. If necessary, trim tab from sensor (P) for doors with 2-3/8" (60mm) backset. Clean surface of door and doorframe, remove film from adhesive, attach and secure close to door edge as shown.
  • Page 18 1 or 2 of the included adhesive foam pads. Once satisfied both sensors are as level as possible, remove film from adhesive and install with arrows aligned to each other with less than a 3/4" gap between each sensor. NOTE: When properly installed, the Lockly logo blinks red when door opens and closes.
  • Page 19 Step 8 INSTALLING STRIKE PLATE Use the supplied door strike or use your existing as long as deadbolt operates smoothly without binding or catching. K(2X) IMPORTANT: because doors and frames vary in design it may be necessary to make slight adjustments to your strike plate and/or dust box in order to ensure smooth deadbolt operation.
  • Page 20 You have completed the Lockly physical lock installation. To enable live monitoring and voice control with Google Assistant or Amazon Alexa, you will need to setup the included Secure Link Wi-Fi hub and pair it with the Lockly Secure Pro deadbolt smart lock door sensors.
  • Page 21 Step 10 SETTING UP THE SECURE LINK WI-FI HUB To set up your Lockly Secure Pro, choose an appropriate location for the Secure Link Wi-fi Hub for optimum performance (see below). For optimum connectivity, it is recommended that the hub be no further away from the lock than 30 feet (9 meters).
  • Page 22 Once you have confirmed that your Secure Link Wi-Fi Hub is ready to connect to your lock, Make sure you are standing between the Wi-Fi open the Lockly App from your smartphone. hub and Lockly smart lock, then Add New Device and follow the on screen instructions.
  • Page 23 Step 11 CONNECTING YOUR LOCKLY SECURE PRO The App will take you through the following steps, make sure the smart lock has been properly installed. You will need your activation card that is included in the box to proceed. ADD NEW DEVICE...
  • Page 24 Step 11 CONNECTING YOUR LOCKLY SECURE PRO continued Plug in your Secure Link Confirm lock password Password setting OK Set the Admin Code and Click "YES" 9:45 AM 100% AT&T 9:45 AM 100% AT&T 9:46 AM 100% AT&T AT&T 9:46 AM 100% Click “Yes”...

  • Page 25: Voice Control

    Amazon Alexa Skill or Lockly Action on Google. TIP: In Google Home or Amazon Alexa app, add Lockly skill for Alexa or Lockly Action on Google, then follow on screen instructions. See full list of commands, help videos, or troubleshooting your Lockly at https://Lockly.com/help...
  • Page 26 FCC Warning： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
  • Page 27 L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1. L’appareil ne doit pas produire de brouillage; 2.
  • Page 28 PM4*12MM （Optional） Screw Foam Pads Exterior Assembly Wired Sensor Sensor Magnet UNF10-32*60mm Screw Wi-Fi Hub Keys Power Adaptor Deadbolt Dust Box Strike Plate KA4*20MM Screw Lockly Secure Pro can be fitted for both right swing doors and left swing doors.
  • Page 29 Connect with us @meetlockly | #Lockly Reference installation parts overview foldout.
  • Page 30 Bluetooth SIG, Inc. , and ® any use of such marks by Lockly is under license. Other trademarks and trade names are those of their respective owners. Google, Android, Google Play and Google Home are trademarks of Google LLC. , Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc., or its affiliates.

This manual is also suitable for:

Pgd728wg20Deadbolt secure pro