The offline access code can allow owners to issue access codes, set the allowed access duration, all without Lockly ® ever connecting to the internet, so in case of power outage, you can still magically and remotely issue Access Codes without any connection to the web.
OAC(Offline Access Code For any questions you can always visit https://lockly.com/help for assistance. Don’t forget that Lockly Lux Compact works best with our iOS and Android app. Please download the app by visiting the link below.
After you have the Activation Code ready, push the reset button on the back panel of the Lockly ® Lux Compact to perform your reset. See below to see which Reset Process applies for you. Once the smart lock has been reset, all the data previously stored will be deleted.
Press and release the reboot button when you want to reboot the lock. Your Lockly will beep once after reboot. Only reboot when necessary. To reboot, find the reboot button located on the bottom of the exterior side of Lockly lock. The reboot button is located in the middle of the two 9V battery backup sockets.
2.7 Low Battery When the battery is in seriously low condition, Lockly will make continuous beeping sounds in addition to the flashing low battery icon on the touch screen. You should replace batteries immediately to avoid your smart lock from shutting down.
2.8 Changing The Battery Under normal use, the Lockly battery will last up to a year. Please check battery levels regularly and change your batteries when the low battery notification is issued. For best practice, always use new batteries by a major brand.
NOTICE The Default Access Code is Your new Lockly Access Code can be any combination of 6 to 8 digits. Once a new Access Code is entered, the Default Access Code of 123456 would be deleted. A maximum of 16 sets of Access Codes can be stored for use at any given time.
Add Access Code Delete Access Code View Access Code After entering Programming Mode, you should see the screen as displayed to the right on your Lockly keypad. Follow the following steps to add, delete, or check your Access Codes. SECTION 3.2...
3.3 Adding an Access Code While in Programming Mode, select “1AD” to add an Access Code. If you are not in Programming Mode, please see Section 3.2 to enter Programming Mode. After pressing “1AD” press “Pd” to add an Access Code. Enter your new 6 - 8 digit Access Code and press when you are finished.
Page 14
3.3 Adding an Access Code (Continued) If you have successfully entered your new Access Code twice, you will see the new code displayed here. In this example, we chose 654321. Press to Confirm or to cancel. To exit or cancel, you can always press If the two (2) Access Codes you entered does not match, an error message will appear on the screen (As shown to the left).
3.4 Deleting an Access Code While in Programming Mode, select “2DE” to delete an Access Code. If you are not in Programming Mode, please see Section 3.2 to enter Programming Mode. After pressing “2DE” press “Pd” to delete an Access Code. Example Only Active Access Codes will then be displayed on the screen in sequence from left to right, top to bottom.
Page 16
3.4 Deleting an Access Code (Continued) Once you have selected the Access Code you want to delete, Lockly will ask you to confirm deletion by showing you the Access Code you are deleting, in this example,1 3 5 7 9 0.
3.5 Checking the Access Codes While in Programming Mode, select “3CH” to check registered Access Codes. If you are not in Programming Mode, please see Section 3.2 to enter Programming Mode. Active Access Codes will then be displayed on the screen in sequence from left to right, top to bottom.
In this section, you will learn how to register a fingerprint to your new smart lock. We are using an advanced biometric sensor, providing the most secure fingerprint authentication. For security reasons, Lockly will only accept fingerprint patterns that consist of cross intersection points. Patterns with no cross intersection points will not be acceptable.
Page 19
Fingerprint. Upon pressing “FP”, you will enter Fingerprint Registration Mode and you will see a green LED ring light up on the fingerprint panel on the exterior side of Lockly. Once you’re in Fingerprint Registration Mode you will see two numbers displayed on keypad.
Page 20
3.6 Adding a Fingerprint (Continued) Please make sure your fingers are clean from dirt and oils before NOTICE scanning your fingerprint. Make sure the sensor is also clean by taking a soft cloth and wiping the surface. Scan your finger by lightly placing your designated finger on the sensor until you hear a beep. Lift your finger and repeat the process slowly until the digit “6”...
3.7 Fingerprint Scanning Directions The fingerprint sensor equipped in your smart lock is loaded with powerful fingerprint algorithms to extract quality features from fingers, even in poor conditions. Placing your finger on the sensor correctly helps consistency in fingerprint recognition. The following directions and tips will guide you on how to scan an optimal fingerprint image.
Page 22
3.7 Fingerprint Scanning Directions (Continued) Top View Side View Correct Incorrect SECTION 3.7...
• If dry - moisturize or blow warm breath over finger before scanning • If dirty - wipe stains and dirt off from finger before scanning • Make sure the sensor is clean from dirt or smudges - wipe sensor with soft cloth regularly For more troubleshooting help, visit http://lockly.com/help SECTION 3.8...
3.9 Deleting Stored Fingerprints* While in Programming Mode, select “2DE” to delete a Fingerprint. If you are not in Programming Mode, please see Section 3.2 to enter Programming Mode. After pressing “2DE” to delete, press “FP” to delete a fingerprint. Your registered fingerprint numbers will be displayed on the screen.
Lockly ® Smart Lock. The Secure Link can be purchased and added anytime. To set up the Lockly ® Lux Compact smart lock with Secure Link Wi-Fi Hub and Door Sensors, launch the Lockly ® App on your iOS or Android device. From the main menu drop down located on the upper left of the screen, select “Add a New Device”...
4.1 Locking/Unlocking with Access Codes Lockly Smart Lock can be unlocked using multiple ways - via your stored Access Code, registered fingerprint, smartphone with Bluetooth, the physical key supplied with your lock, or voice (with Secure Link Wi-Fi Hub installed) Slide your hand across the screen to activate the keypad.
4.2 Locking/Unlocking Lockly with Fingerprints Unlocking Place a registered finger to the fingerprint scanner located on the exterior side of the lock to the right. To register a fingerprint, please see Section 3.6. If your fingerprint is registered and acknowledged, you will hear a “beep”...
App ® You must have the Lockly ® iOS or Android app installed in order to lock and unlock with smartphone and connect with voice assistants like Alexa or Google Assistant. Please download the app by visiting the link below or search “Lockly” from the correct app store.
4.4 Locking/Unlocking with Physical Key Exterior View To unlock your lock using the physical key (included), open the key cover on the handle by turning the cover to reveal the keyhole. Insert your key and turn clockwise or counter clockwise to lock or unlock the door. SECTION 4.5...
This smart lock is built with an anti-friction latch throw and a heavy steel deadbolt throw for added security. The latch throw can be setup to auto lock based on your customized timing through the Lockly app. The deadbolt throw is connected to the door handle. To UNLOCK pull the handle downwards and push door to open.
4.6 Locking and Unlocking with Voice Assistants Once your Lockly ® Smart Lock and Secure Link¹ Wi-Fi Hub has been installed and configured correctly, make sure you enable the Lockly ® Action for Google Assistant or the Amazon Alexa Skill before you can configure your voice to perform voice commands.
4.7 Safe Mode - Overview Lockly will enter Safe Mode when three (3) consecutive wrong Access Codes are entered within 5 minutes. When in Safe Mode, the lock status icon will start to flash. To disable Safe Mode, you must unlock the door using the correct fingerprint or enter the correct Access Code twice in a row.
Page 33
Option 2 - Lockly Bluetooth App Use the app that is synced to your Lockly to disable Safe Mode by unlocking the door. If you have not downloaded the app to use with your smart lock, you won’t be able to use this option to disable Safe Mode.
To use the OAC feature, make sure you download the Lockly app for iOS or Android first, and sync your smart lock to your mobile device. OAC can only be issued by the administrative owner of the lock.
Lockly App. 9V Backup Access n your Lockly is out of power, you can temporarily activate the keypad by using a 9V battery against the bottom of the exterior side of the smart lock. Please see Section 2.6 for more info.
7.1 Cleaning Making sure your Lockly is clean is best practice to ensure optimal product use. Follow the DOs and DON’Ts below. DON’T • Don’t use abrasives, high alkaline • Rinse the touchscreen with warm cleaners, or gasoline to clean your lock.
8.1 Safety Precautions Please read all instructions carefully. Remind all Lockly users of the safety precautions. Read the following instructions for your own safety Do not attempt to disassemble the smart lock by yourself. It can cause product damage, void warranty, and cause injuries.
Page 38
Certified FCC Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Page 39
WARNING: This product contains DEHP and other chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. For more information go to www.P65Warnings.ca.gov LUX COMPACT We’re here to help! help@lockly.com https://lockly.com/help...
Page 40
Other Patents Pending With All Rights Reserved About Lockly Secure, Secure Plus and Secure Pro About Lockly Secure, Secure Plus and Secure Pro are keyless smartlocks equipped with the patented PIN Genie , which is a peep proof and hidden camera proof algorithm software.