Related Manuals for Lockly Secure LUX
Summary of Contents for Lockly Secure LUX
- Page 1 MORTISE EDITION SECURE LUX MORTISE LOCK INSTALLATION MANUAL...
- Page 2 Lock Cylinder Screw for Inner Panel Escutcheon Fixing Screw Escutcheon Escutcheon Pad Lockset Lockset Fixing Screws Shaft Exterior Panel Lock Cylinder Screw Buckle Box Strike Screw Lockly Secure can be fitted for both right swing doors and left swing doors.
- Page 3 PARTS LIST 50~60MM STANDARD DOOR THICKNESS Cotter Pin hole is here when door thickness is larger than 70mm Cotter Pin hole is here when door thickness is less than 70mm Turnable Flat Strip (1) Buckle Box (1) Strike (1) Lock Cylinder (1) Shaft (1) Position Pad (2) Screw for Lockset (4)
- Page 4 KNOW YOUR DOOR There are 4 common door-opening directions, the lockset configuration as shown on each diagram below corresponds to the respective door-opening direction. RIGHT IN-SWING DOOR Make sure the latch throw is correctly oriented as shown to fit your right in-swing door Make sure the pit hole is correctly oriented as shown.
- Page 5 KNOW YOUR DOOR LEFT IN-SWING DOOR Make sure the latch throw is correctly oriented as shown to fit your left in-swing door Make sure the pit hole is correctly oriented as shown. LEFT OUT-SWING DOOR Make sure the latch throw is correctly oriented as shown to fit your left out-swing door Make sure the pit hole is...
- Page 6 HOW TO ADJUST THE LATCH THROW Here is how to change the latch throw direction. The factory setting of the throw is for right in-swing door. You do not need to change direction if you have a right in-swing door. 2.
- Page 7 HOW TO ADJUST THE CYLINDER Here is how to change the cylinder direction. The factory setting of the cylinder is for right in-swing door. You do not need to change direction if you have a right in-swing door. 1. You need a Phillips screwdriver. 2.
- Page 8 HOW TO ADJUST THE DOOR HANDLE *The diagram below shows how to shift the door handle from right to left direction. The factory setting of the handle is for right handed door. You do not need to change direction if you have a right handed door. 1.
- Page 9 STEP 1: PREPARING YOUR DOOR Hole template Centerline above 1M from ground. Hole for handle Make sure your door is prepared for installation. You may need to drill a new hole. Please use the supplied template for drilling holes required before installation. You will need some tools or a hole-saw.
- Page 10 STEP 2: INSTALLING THE LOCKSET Route the cable inside the door Fixing Screws (X4) Lockset Make sure the pit hole of this spin is pointed downward and facing the door outside during installation. Install the mortise lockset into door pocket and tighten it with the 4 screws supplied. Route the cable inside the door pocket and place it aside.
- Page 11 STEP 3. INSTALLING THE LOCK CYLINDER AND THE SPINDLE Lock Cylinder Fixing Screws for Lock Cylinder(X2) Remove this plastic cover before installing the lock cylinder. Spindle(X2) Spindle Pad(X2) 23.5 1 2 3 4 Note: If the door thickness is less than 70mm cut screw for outer panel to 23.5mm, that is from the 4th scale cut-off to the end.
- Page 12 STEP 4. INSTALLING THE EXTERIOR PANEL Shaft Position Sleeve (Should be removed after the shaft is positioned) Outer Panel Fixing Screw Outer Panel Fixing Screw Gasket Escutcheon Note: This shaft needs to be inserted through the outer part of the door Insert the square shaft through the exterior panel.
- Page 13 STEP 5 . INSTALLING THE INTERIOR PANEL Remove and discard the positioning sleeve then insert both lock cables to the correspond- ing socket of the interior panel. Insert the cotter pin to the flat shaft. See notes as illustrated in the diagram. Then insert the flat shaft to the corresponding holes and tighten with screws provided.
- Page 14 STEP 6. FINAL CHECK After installation is completed, lift both the interior and exterior handles up and down making sure they are running smoothly. Then check if the deadbolt and strike plate is thrown smoothly with the physical keys. STEP 7. INSTALLING BATTERIES Check the functions of the lock per user manual after installing the batteries.
- Page 15 STEP 8. PREPARING THE DOOR FRAME AND MOUNTING PLATE Install the buckle box as shown below. Open the door frame, install buckle box, then the strike plate and fix it with screws. When installing to a wooden door, cut the buckle box as shown.
- Page 16 SECURE For an online version of this installation guide and videos, visit: http://lockly.com/help IGPGD82920190423...