Lockly Secure User Manual
  1. Manuals
  2. Brands
  3. Lockly Manuals
  4. Locks
  5. SECURE
  6. User manual

Lockly Secure User Manual

Smart lock. deadbolt edition
Hide thumbs Also See for Secure:
Table of Contents

Advertisement

Quick Links

See also: Installation Manual
DEADBOLT EDITION
SECURE PLUS | SECURE PRO
USER MANUAL

Advertisement

Table of Contents
loading

Related Manuals for Lockly Secure

Summary of Contents for Lockly Secure

  • Page 1 DEADBOLT EDITION SECURE PLUS | SECURE PRO USER MANUAL...
  • Page 2 Other Patents Pending With All Rights Reserved About Lockly™ Secure, Secure Plus and Secure Pro Lockly™ Secure, Secure Plus and Secure Pro are keyless smart locks equipped with the patented PIN Genie , which is a peep proof and hidden camera proof algorithm software.

  • Page 3: Table Of Contents

    Section 8 - Safety Precautions Adding an Access Code Deleting an Access Code Safety Precautions Checking an Access Code Adding a Fingerprint Fingerprint Scanning Directions Fingerprint Tips & Troubleshooting Deleting Stored Fingerprints For additional support, visit http://lockly.com/help or email help@Lockly.com TABLE OF CONTENTS...

  • Page 4: Product Features

    The offline access code can allow owners to issue access codes, set the allowed access duration, all without Lockly™ ever connecting to the internet, so in case of power outage, you can still magically and remotely issue Access Codes without any connection to the web.

  • Page 5: Product Overview - Outside

    2.1 Product Overview - Outside OK Button Lock Status Icon Power Status Bluetooth light Bluetooth icon Key Hole Key Hole Cover Restart Button 9V Battery Emergency Charging Socket SECTION 2.1...

  • Page 6: Product Overview - Inside

    2.2 Product Overview - Inside Battery Cover Battery Compartment ( Operated by 4 x AA Batteries) Thumbturn Reset Button Display Keypad Switch Program Button Beep Alert SECTION 2.2...

  • Page 7: Understanding Your New Lock

    The following guides will walk you through resetting a lock, adding Access Codes, deleting Access Codes, adding and deleting fingerprints (Applicable to Secure Plus and Secure Pro only) and also how to configure your OAC (Offline Access Code).

  • Page 8: Factory Reset

    (Was n the Quick Start Guide) After you have the Initial Code ready, push the reset button on the back panel of the Lockly™ to perform your reset. See below to see which Reset Process applies for you. Once the smart lock has been reset, all the data previously stored will be deleted.

  • Page 9: Rebooting Lockly™ Secure

    Press and release the reboot button when you want to reboot the lock. Your Lockly™ will beep once after reboot. Only reboot when necessary. To reboot, find the reboot button located on the bottom of the exterior side of Lockly™ Secure. The reboot button is located in the middle of the two 9V battery backup sockets.

  • Page 10: Low Battery

    2.7 Low Battery When the battery is in seriously low condition, Lockly™ will make continuous beeping sounds in addition to the flashing low battery icon on the touch screen. You should replace batteries immediately to avoid your smart lock from shutting down.

  • Page 11: Changing The Battery

    2.8 Changing The Battery Under normal use, the Lockly™ battery will last up to a year. Please check battery levels regularly and change your batteries when the low battery notification is issued. For best practice, always use new batteries. Open the battery compartment cover and insert four (4) new AA alkaline batteries as shown.

  • Page 12: Configuring Access

    NOTICE The Default Access Code is Your new Lockly™ Access Code can be any combination of 6 to 8 digits. Once a new Access Code is entered, the Default Access Code of 123456 would be deleted. A Maximum of 8 sets of Access Codes can be stored for use.

  • Page 13: Entering Programming Mode

    3.2 Entering Programming Mode To enter Programming Mode, remove the battery compartment cover on the interior side of the Secure to expose the Reset and Program buttons. Simply press the Program button to enter programming mode. Program Button Note: Program button will be disabled once synced to a smart phone.

  • Page 14: Adding An Access Code

    3.3 Adding an Access Code While in Programming Mode, select “1AD” to add an Access Code. If you are not in Pro- gramming Mode, please see Section 3.2 to enter Program- ming Mode. After pressing “1AD” press “Pd” to add an Access Code. Enter your new 6 - 8 digit Access Code and press when you are finished.
  • Page 15 3.3 Adding an Access Code (Continued) If you have successfully entered your new Access Code twice, you will see the new code displayed here. In this exam- ple, we chose 654321. Press to Confirm or to cancel. To exit or cancel, you can always press If the two (2) Access Codes you entered does not match, an error message will appear on the screen (As shown to the left).

  • Page 16: Deleting An Access Code

    3.4 Deleting an Access Code While in Programming Mode, select “2DE” to delete an Access Code. If you are not in Programming Mode, please see Section 3.2 to enter Pro- gramming Mode. After pressing “2DE” press “Pd” to delete an Access Code.
  • Page 17 3.4 Deleting an Access Code (Continued) Once you have selected the Access Code you want to delete, Lockly™ will ask you to confirm deletion by showing you the Access Code you are deleting, in this example, 1 3 5 7 9 0.

  • Page 18: Checking An Access Code

    3.5 Checking the Access Codes While in Programming Mode, select “3CH” to check registered Access Codes. If you are not in Programming Mode, please see Section 3.2 to enter Programming Mode. Active Access Codes will then be displayed on the screen in sequence from left to right, top to bottom.

  • Page 19: Adding A Fingerprint

    In this section, you will learn how to register a fingerprint to your new smart lock. Fingerprint registration is only available in the Lockly™ Secure Plus / Pro, and not available in Secure models. If you have Secure, you may skip to Section 4.1 to learn about locking and unlocking your door with Lockly™.
  • Page 20 Upon pressing “FP”, you will enter Fingerprint Registration Mode and you will see a green LED ring light up on the fingerprint panel on the exterior side of Lockly™ Secure Plus / Pro. Once you’re in Fingerprint Registration Mode you will see two numbers displayed on keypad.
  • Page 21 3.6 Adding a Fingerprint (Continued) Please make sure your fingers are clean from dirt and oils NOTICE before scanning your fingerprint. Make sure the sensor is also clean by taking a soft cloth and wiping the surface. Scan your finger by lightly placing your designated finger on the sensor until you hear a beep. Lift your finger and repeat the process slowly until the digit “6”...

  • Page 22: Fingerprint Scanning Directions

    3.7 Fingerprint Scanning Directions The fingerprint sensor equipped in Lockly™ Secure Plus / Pro is loaded with powerful fingerprint algorithms to extract quality features from fingers, even in poor conditions. Placing your finger on the sensor correctly helps consistency in fingerprint recognition.
  • Page 23 3.7 Fingerprint Scanning Directions (Continued) Top View Side View Correct Incorrect SECTION 3.7...

  • Page 24: Fingerprint Tips & Troubleshooting

    • If dry - moisturize or blow warm breath over finger before scanning • If dirty - wipe stains and dirt off from finger before scanning • Make sure the sensor is clean from dirt or smudges - wipe sensor with soft cloth regularly For more troubleshooting help, visit http://lockly.com/help SECTION 3.8...

  • Page 25: Deleting Stored Fingerprints

    3.9 Deleting Stored Fingerprints While in Programming Mode, select “2DE” to delete a Finger- print. If you are not in Program- ming Mode, please see Section 3.2 to enter Programming Mode. After pressing “2DE” to delete, press “FP” to delete a fingerprint. Your registered fingerprint numbers will be displayed on the screen.

  • Page 26: Locking / Unlocking Using Access Codes

    4.1 Locking/Unlocking Lockly™ with Access Codes Lockly™ Secure can be unlocked using 1 of 4 ways - via your stored Access Code, registered fingerprint (Secure Plus / Pro only), smartphone with Bluetooth, or with the physical key supplied with your lock.

  • Page 27: Locking / Unlocking Using Fingerprint

    You must wait until the red LED is off to try again. For best fingerprint scanning practices, see Section 3.7. Locking OK Button To lock the Lockly™, press the OK Button anytime when the door is opened. SECTION 4.2...

  • Page 28: Locking / Unlocking Using App

    4.3 Locking/Unlocking Lockly™ with App You must have the Lockly™ iOS or Android app installed in order to lock and unlock with the smartphone app. Please first download the app from the correct store. Scan or visit Lockly.com/app Please see the smartphone app manual to follow instructions on how to connect your app to your lock via Bluetooth and learn how to lock / unlock the door using the app.

  • Page 29: Locking / Unlocking Using Physical Key

    4.4 Locking/Unlocking Lockly™ with Physical Key Exterior View To unlock your Lockly™ using the physical key (supplied), open the key cover on the handle by turning the cover counter clockwise to reveal the keyhole. Insert your key and turn clockwise or counter clockwise to lock or unlock the door.

  • Page 30: Safe Mode

    5 minutes. When in Safe Mode, the lock status icon will start to flash. To disable Safe Mode, you must unlock the door using the correct fingerprint (Secure Plus / Pro ) or enter the correct Access Code twice in a row. Activate the keypad by pressing and holding for 3 seconds.
  • Page 31 Option 2 - Lockly™ Bluetooth App Use the app that is synced to your Lockly™ to disable Safe Mode by unlocking the door. If you have not downloaded the app to use with your smart lock, you won’t be able to use this...

  • Page 32: Offline Access Code (Oac)

    To use the OAC feature, make sure you download the Lockly™ app for iOS or Android first, and sync your smart lock to your mobile device.

  • Page 33: Important Notes

    9V Backup Access When your Lockly™ is out of power, you can temporarily activate the keypad by using a 9V battery against the bottom of the exterior side of the smart lock. Please see Section 2.6 for more info.

  • Page 34: Cleaning

    7.1 Cleaning Making sure your Lockly™ is clean is best practice to ensure optimal product use. Follow the DOs and DON’Ts below. DON’T • Don’t use abrasives, high alkaline • Rinse the touchscreen with warm cleaners, or gasoline to clean your water prior to cleaning.

  • Page 35: Safety Precautions

    8.1 Safety Precautions Please read all instructions carefully. Remind all Lockly™ users of the safety precautions. Read the following instructions for your own safety Do not attempt to disassemble the smart lock by yourself. It can cause product damage, void warranty, and cause injuries.
  • Page 36 Certified Warning： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

This manual is also suitable for:

Secure plusSecure pro

Table of Contents