Related Manuals for Kargo Master 4082L
Summary of Contents for Kargo Master 4082L
- Page 1 Installation Guide 4082L Kargo Master Rancho Cordova, CA 95742 800-343-7486 CustomerService@KargoMaster.com 20210630R6 DATE: __________________...
-
Page 2: Table Of Contents
Examples of Ladder Clamps Firmly Against Ladder Rungs ................12 Before You Begin Read all instructions prior to assembling or installing any Kargo Master product. Have vehicle specific mount kit installed on vehicle. Most times it is easier to assemble on top of the roof, after the mount kit has been installed. -
Page 3: Parts List
Instructions – 4082L Parts List For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 2... -
Page 4: Hardware
Instructions – 4082L Hardware For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 3... -
Page 5: Step 1 ─ Install Ladder End Stops
Instructions – 4082L Step 1 ─ Install Ladder End Stops Skip this step if adding a driver side add on rack. Install ladder stops at the end of each bow using 5/16” x 1” carriage bolts, 5/16” flat washers and 5/16”... -
Page 6: Step 3 - Install Side Tube
Instructions – 4082L Using the hardware from the mount kit, attach the bow to the feet. Be sure the feet are using the same slots on each side of the bow. Step 3 – Install Side Tube Insert the J-Tube into the tube as shown. -
Page 7: Step 4 - Install Hanger Bracket
Instructions – 4082L Place on top of the installed bows. Have the orientation of the J-Tube towards the front and to the outside of the vehicle. Leave on square slot open at the rear of the tube. Mount tube assembly to the bows using 5/16” x 2” carriage bolts, 5/16” flat washers and 5/16” lock nuts. -
Page 8: Step 5 - Mount Long Angle Bracket
Instructions – 4082L Step 5 – Mount Long Angle Bracket Place the plastic bushings on the rotating clamp as shown. Place the angle L-bracket on top of the bows as shown. Be sure the bend offset is towards the center of the vehicle. - Page 9 Instructions – 4082L Attach the long angle bracket to both bows in the orientation shown using 3/8” x 1” carriage bolts, 3/8” flat washers and 3/8” lock nuts. For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST)
-
Page 10: Step 6 - Mount Handle
Instructions – 4082L Step 6 – Mount Handle Bolt the handle to the rotating clamp in the order shown using a 3/8” x 3” hex head, a 3/8” flat washer, 3/8” nylon washer, 3/8” contour washer and a 3/8” lock nut. The nylon washer goes in between the rotating clamp and the handle. -
Page 11: Step 7 - Mount Latch Assembly
Instructions – 4082L Step 7 – Mount Latch Assembly Attach the latch assembly to the rear most square hole in the tube using 5/16” x 2” carriage bolt, 5/16” flat washer and 5/16” lock nut. Step 8 – Install Ladder Hook to Bow ... - Page 12 Instructions – 4082L Adjust the ladder clamp to firmly secure the ladder being used on the ladder rack. Flipped orientation shown here. GO BACK AND ENSURE ALL HARDWARE IS TIGHT. YOUR INSTALLATION IS NOW COMPLETE. Refer to the Clamp and Lock Adjustment instructions to adjust the rack to your ladder.
-
Page 13: Angle Pad Orientations And Locations
Instructions – 4082L Angle Pad Orientations and Locations Standard Flipped Oritentation Orientation Clamp Mechanism Orientation and Angled Pad Positions Rear- Facing Examples of Ladder Clamps Firmly Against Ladder Rungs Be sure to position the ladder hook in a way so the hook clamps the ladder tight into place. A tight fit ensures the ladder cannot fall off the rack.