Advertisement
Quick Links
IMPORTANT
Part List
B.
Rail
2 pcs.
E.
Bottom
1 pc.
I.
Shelf
3 pcs.
Hardware List
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Cartons 20 05520 0921 and 0922 are also needed for assembly.
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/16" Drill Bit, 3/8" Drill Bit
20 05520 0923
Storage Island
Flat Washer
Cam Lock
12 pcs. (+1 extra)
30 pcs. (+6 extra)
Cam Lock Screw
Adjustable Pin
30 pcs. (+2 extra)
12 pcs. (+1 extra)
C.
Rail
3 pcs.
Refer to later page(s) of these instructions for drawer assembly.
Spring Washer
12 pcs. (+1 extra)
M3 x
.5 32
Wood Screw
4 pcs. (+1 extra)
J.
Drawer
1 pc.
K.
Drawer
3 pcs.
M6x32
Head Cap Bolt
12 pcs. (+1 extra)
M4x16
Machine Screw
8 pcs.
F.
Plinth
2 pcs.
Handle
4 pcs.
Advertisement
Related Manuals for Home Styles 20 05520 0923
Summary of Contents for Home Styles 20 05520 0923
- Page 1 20 05520 0923 Storage Island IMPORTANT Part List Rail Rail Plinth 2 pcs. 3 pcs. 2 pcs. Bottom Drawer 1 pc. 1 pc. Shelf Drawer 3 pcs. 3 pcs. Refer to later page(s) of these instructions for drawer assembly. Hardware List...
- Page 2 Assembly Instructions 2/8 IMPORTANT Ÿ Use a soft cloth between these parts and the floor. Ÿ Do not use power tools above 8 volts to assemble. Ÿ Do not tighten all the bolts until each part is properly assembled. Ÿ The unit must be level to work properly.
- Page 3 Assembly Instructions 3/8 STEP 2 Attach Back Panel (D) to Bottom (E) with Cam Locks. (See Figure 2) Attach Plinths (F) to unit with Cam Locks. Cam Lock Figure 2 Wood Screw Flat Washer Spring Washer Head Cap Bolt STEP 3 Attach unit form Step 2 to Side Panel (H) with Flat Washers, Spring Washers, Head Cap Bolts...
- Page 4 Assembly Instructions 4/8 Wood Screw STEP 4 Attach Side Panel (G) to unit with Cam Locks, Flat Washers, Spring Washers, Head Cap Bolts and Wood Screws, tightening bolts only halfway. Cam Lock Turn unit to it’s Flat Washer upright position. Spring Washer Head Cap Bolt Adjustable Pin...
-
Page 5: Part List
Assembly Instructions 5/8 Drawer (J) STEP 6 Attach Drawer Sides (J3) and (J4) to Drawer Back (J2), then flip Locks. (See Figures 4 and 5) Lock Figure 4 Figure 5 STEP 7 Slide Drawer Bottom (J5) into groove. Attach Drawer Front (J1) to unit, then flip Locks. - Page 6 Assembly Instructions 6/8 Drawer (K) STEP 9 Lock Attach Drawer Sides (K3) and (K4) to Drawer Back (K2), then flip Locks. STEP 10 Slide Drawer Bottom (K5) into groove. Attach Drawer Front (K1) to unit, then flip Locks. Lock Machine Screw STEP 11 Attach Handle with Machine Screw.
- Page 7 Assembly Instructions 7/8 Flat Washer Spring Washer Head Cap Bolt Cam Lock STEP 12 Attach Top (A) to unit with Cam Locks Flat Washer, Spring Washer and Head Cap Bolts, tightening bolts only halfway. STEP 13 Level unit by adjusting the adjustable levelers on bottom of unit.
-
Page 8: Hardware List
Assembly Instructions 8/8 Per regulatory requirements, a Tip-over Restraint is included. Follow Step 14 to install it. STEP 14 Drill a 3/16” hole 1/2” deep 1” below top of unit in middle of side panel that is Anchor in wall Wall Screw Bracket 3/16”... - Page 9 Buff with a dry clean cloth. Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized retail affiliate, Home Styles is under no obligation to provide replacement parts.
Need help?
Do you have a question about the 20 05520 0923 and is the answer not in the manual?
Questions and answers