Subscribe to Our Youtube Channel
Related Manuals for Ayra ERO Motion Heads 1W
Summary of Contents for Ayra ERO Motion Heads 1W
- Page 1 ERO Motion Heads 1W LED Moving Head User Manual The information in this user manual is subject to change at any time without notice. Version: 1.0 Date of creation and author's initials: 07-10-2019 RV Revision date and author's initials: -...
- Page 2 'Box contents' are included in the package. In the event that the ERO Motion Heads 1W does not function properly, or if you have any issues while operating it, please remove the plug from the power socket and contact your retailer for assistance.
-
Page 3: Safety Instructions
Safety Instructions WARNING! Keep this device away from moisture, water and rain to avoid the chance of electric shocks. WARNING! Only connect this device to a suitable power socket. This device functions on a specific power voltage. If it is plugged into a power socket with a different voltage, it could result in permanent damage and even dangerous situations such as fire or electric shocks. - Page 4 - Should the device not be used in the manner described in this user manual, damages or even injuries could occur. Ayra cannot be held responsible for any injuries or damages that occur as a result of improper use of this product.
- Page 5 Only suitable for indoor use: this product was only designed for indoor use. The maximum environmental temperature must not exceed 40 degrees Celsius (104 degrees Fahrenheit). Contact: Ayra professional lighting products Verrijn Stuartweg 18 4462 GE Goes The Netherlands Please do not send any products to this correspondence address.
- Page 6 Overview and Operation Guidelines for this Device Moving head with light putput via lens DMX input and output via 3-pins XLR LED display with menu buttons Rubber feet Mounted suspension bracket The power cable is not displayed in the picture. The information in this user manual is subject to change at any time without notice.
- Page 7 During start up, either ‘AYRA’ or a specific code will be shown on the display, which means the device is not ready to be operated. Once the device has fully started up, it will jump to the last-used mode. Operation modes and other settings shown on the display can now be adjusted or changed by means of the menu buttons.
- Page 8 means of standard 3-pin XLR cables. The only difference is that the first device in the chain does not receive DMX input. PLEASE NOTE: When Slave mode is activated, the device will wait for a signal from the Master device. It is not possible to simply select an automatic or sound-controlled mode! To cancel this, select 'NAST' mode in the SLND menu, so the device goes to Master mode.
- Page 9 Operating Modes The following overview is designed to show the differences between the various operation modes that are supported by the above-mentioned menu functions. Sound: When in Sound-controlled mode, the device's internal microphone detects the music and reacts to the beat. The device will move in sync with the music and provide an automated light show.
- Page 10 Upright use If you want to use the ERO Motion Heads 1W in an upright position, ensure that it is placed on a stable surface like a table, DJ booth or T-bar. The ERO Motion Heads 1W is equipped with rubber feet that grip suitable surfaces.
- Page 11 Check if all the screws are intact and secured and tighten or replace them where needed. Check all metal parts of the device for any signs of corrosion. If corrosion is found, the device needs to be checked thoroughly. DMX terminator In DMX mode, it’s standard practice to place a terminator at the end of a DMX circuit.
- Page 12 DMX Lighting Troubleshooting If you have a problem with your DMX light effect, please consult the troubleshooting section for possible solutions. If, after consulting this section, the problem remains unresolved, please contact your dealer for more information and/or help. This troubleshooting section contains information on how to solve the most common DMX light effect problems, but it does not and cannot cover every eventuality.
- Page 13 The operating mode can not be The device is in Slave mode If the device is in Slave mode, it changed will wait for a master signal unless there is a DMX signal present. Set the device to Master to activate the sound-controlled or automated operation modes.
-
Page 14: Technical Specifications
Technical Specifications Specifcations: - Compact LED moving head - Metal housing with plastic covers - Light source: 10 Watt white LED - Various operating modes - Automatic mode with 4 customisable programs and 9 speed settings - Sound-controlled mode with adjustable sensitivity - Master / Slave mode - Pan / Tilt inversion mode - DMX operation via 7 channels...
Need help?
Do you have a question about the ERO Motion Heads 1W and is the answer not in the manual?
Questions and answers