Subscribe to Our Youtube Channel
Related Manuals for Oxgard Praktika T-02
Summary of Contents for Oxgard Praktika T-02
- Page 1 Installation guidelines Praktika T-02(К) turnstile www.oxgard.com info@oxgard.com Tel.+7(812) 366-15-94...
-
Page 3: Table Of Contents
Contents 1. Basic specifications .................. 5 2. Product design ..................6 3. Safety requirements ................10 4. Installation of turnstile ................11 4.1. Required equipment ................ 11 4.2. Installation of turnstile ..............12 5. Connecting turnstile ................14 5.1. Connecting power supply ..............17 5.2. - Page 4 List of abbreviations – power supply – fire alarm – remote control – access control system – operating device (turnstile) – normally connected – normally opened Turnstile firmware version FW v1.76 Card collector firmware version FW v1.52 Praktika T-02(K) turnstile...
-
Page 5: Basic Specifications
1. Basic specifications Table 1 Basic specifications Description Turnstile RC panel Dimension (HхWхL), (mm) 1100х1050х840 107х107х25 - operational state 1100х1050х340 - collapsed arms Weight, kg 66,0 Temperature range, 0C +1...+40 +1...+40 - operation +1...+40 +1...+40 - transportation and storage Atmosphere relative humidity, no more than Passage width, mm Throughput, people per minute Card collector capacity (pcs.) -
Page 6: Product Design
Turnstile housing and arms are made of brushed stainless steel. turnstile can be equipped with an integrated card collector. In this case a turnstile is marked PRAKTIKA T-02- (R). If the turnstile is not equipped with card collector the turnstile is marked PRAKTIKA T-02. Proximity card readers can be installed on both variants. - Page 7 Fig. 1 General view of turnstile Dimensions are shown on Fig. 2. Installation guidelines...
- Page 8 Display system of turnstile consists of two LED panels. The panels are made of artificial stone with an insertion made of acrylic glass. Turnstile operating modes are displayed on the panel in the form of mnemonic signs depicting authorization and non-authorization of passage (Fig. 3). Praktika T-02(K) turnstile...
- Page 9 Fig. 3 General view LED panel display Remote Control Panel The housing of RC is made of polished stainless steel. On the front side there are control buttons 1-4 and LED indicators of RC operational modes (Fig. 4). The standard supplied cable is 5 meters long. Fig.
-
Page 10: Safety Requirements
• Set the power supply inside the turnstile housing as this could lead to electric shock to persons; • Set the turnstile other than dry and heated places; • Impede or accelerate the turnstile arms during on/off “antipanic” mode; Apply chemically aggressive cleaning detergents as pastes and liquids. Praktika T-02(K) turnstile... -
Page 11: Installation Of Turnstile
4. Installation of turnstile CAUTION: The turnstile should be installed securely to avoid swinging and (or) overthrow during operation. In case of installation on the low strength floors - take action to strengthen the floor at the installation site. Before checking operability of the turnstile carefully read this section of the Regulations. -
Page 12: Installation Of Turnstile
5mm. Put anchors into the holes. 4.2.4. Cable routing is carried out through a holes 1 or 2 (Fig. 5) in the lower plate of turnstile. Fig. 5 Linkage dimension Praktika T-02(K) turnstile... - Page 13 4.2.5. Open the box and unpack: • turnstile; • remote control panel with cable; • lock keys (8 pcs.). 4.2.6. Route cable of RC panel, cable of PS unit and, if provided, cables of FA and ACS into cable conduit. 4.2.7.
-
Page 14: Connecting Turnstile
Connection of RC, PS and ACS is performed with the use of motherboard. In order to do it, remove the housing cover (1, Fig. 6) with a key. Fig. 7 shows the location of motherboard in the turnstile. Praktika T-02(K) turnstile... - Page 15 Fig. 7 Location of motherboard Fig. 8 shows the appearance of motherboard and connectors for PS, RC, ACS and FA cables. Installation guidelines...
- Page 16 Status of the buttons is transmitted to I / O1 ... I / O4 outputs (see. 5.4) - Jumper J3 is not used - Jumper J4 is used to establish the normal operation of CAN2.0 bus. See Appendix 1. Praktika T-02(K) turnstile...
-
Page 17: Connecting Power Supply
5.1. Connecting power supply CAUTION! Do not use power supplies with an output current less than Do not install the power supply at a distance more than 25 meters from the turnstile. CAUTION! Do not use power cable with cross-section less than 1.5 mm for connection. -
Page 18: Connecting Remote Control Panel
Contacts marking Wire color Yellow Green Blue 5.3. Connecting access control system (optional) ACS controller is connected to AccessControlSystem contact set on motherboard. Marking of contacts: LEFT, RIGHT, STOP, AP, GND. Contact assignment is shown in Table 5. Praktika T-02(K) turnstile... - Page 19 Table 5. ACS contacts assignment Contacts marking Contacts assignment single pass left / right LEFT, RIGHT (lowest priority) non-authorized (mode "Stop") STOP (medium priority) arms folding ("antipanic") (highest priority) common contact Inputs for connecting of ACS differ on priorities: AP input has the highest priority. As long as this input is closed GND contact, arms of the turnstile are collapsed and the turnstile does not respond (!!!) to other signals;...
- Page 20 Motherboard contains relay output for ACS operating on the principle of "dry contacts» - Status. NO and COMM - normally open connection, its contacts close when the turnstile switches to "AP" and D3 LED indicator lights up. Also the motherboard contains the following LED indicators: Praktika T-02(K) turnstile...
-
Page 21: Connecting Rc Panel To Acs Controller
D4 indicates a signal to the «LEFT» input. D5 indicates a signal to the «RIGHT» input. D6 indicates signal to the «STOP» input. D7 signals a signal to the «AP» input. Jumper J4 shall be installed. It is used to connect a 120 Ohm resistor to ensure normal operation. - Page 22 Fig. 9 Numbering of RC panel buttons Praktika T-02(K) turnstile...
- Page 23 Table 6. I/O contact set assignment Contacts Contact assignment marking I/O1 "Left" button status (1, Fig.9) I/O2 "Right" button status (3, Fig. 9) I/O3 "Stop" button status (2, Fig. 9) I/O4 "Antipanic" button status (4,Fig.9) I / O1 ... I / O3 outputs show the current state of RC panel buttons, i.e. transistor is opened by pressing the corresponding button.
- Page 24 RC panel buttons (except for the free passage in the potential control mode. See section 5.3 of Manual). In this case ACS controls these operation modes. Fig. 11 Connection pattern of RC to ACS controller Praktika T-02(K) turnstile...
-
Page 25: Connecting Card Collector
6. Connecting card collector 6.1. Card collector description In front of the housing there is a hatch with lock for quick access to collected cards and to the board when PS, OD and ACS cables are connected (fig. 12). The hatch includes a card storage device. Fig. -
Page 26: Connecting Power Supply
Fig. 13 shows general view of board and connectors for PS, OD and ACS. Fig. 13 General view of board 6.2. Connecting power supply Card collector is powered by a 12 V DC voltage source. Maximum consumption is present in the mode of card collection - 1.5A. Praktika T-02(K) turnstile... - Page 27 Locate the PS unit to be accessible for operator. Connect PS cable to the card collector board. Connect (+) and (-) contacts of power supply to (+ 12V) and (GND) contacts on the board respectively (Fig. 13). When the card collector board is powered, D11 LED indicator will turn on. Make sure that cable is connected securely.
-
Page 28: Connecting Acs Controller
Passage is detected by a contact closure for at least 200 ms. The signal for collection shall be transmitted no sooner and no later than 2 seconds after putting the card into the card hole of the card Praktika T-02(K) turnstile... - Page 29 collector, otherwise it will be ignored. After receiving the signal within the mentioned time interval card collector opens the shutter and the card is collected. If card collection is confirmed by internal sensors, card collector generates a signal to the OD via "Let Go" contact set (see. article 6.3.1) and to ACS via "Card Inside"...
- Page 30 NC, NO, and COMM contacts. Relay output operating on a "dry contact" principle which closes / opens for 1 second transmitting a confirmation signal of card collection to the ACS controller. NC and COMM - normally closed connection, NO and COMM - normally open connection. Praktika T-02(K) turnstile...
-
Page 31: Installation Of Proximity Card Reader
6.5. Installation of proximity card reader MatrixIII proximity card reader is used as an example of installation. Installation of other models of readers may differ. 6.5.1. Undo the M4 screw (1, Fig. 6) at the rear of the card collector (Fig. 14). Fig. - Page 32 Tighten the M4 screw and set the decorative cover (1, Fig. 6). CAUTION! When installing the LED panel in its original position, make sure that wires of optical sensors mounted on the guiding bars for cards will not be damaged by other elements. Praktika T-02(K) turnstile...
- Page 33 Fig. 15 Installation of proximity card reader Fig. 16 Recommended option of card reader installation Installation guidelines...
- Page 34 120 ohm resistors are already installed at the ends of the bus (in RC panels). J4 jumper can be taken off. A special RC panel is required to operate several turnstiles simultaneously. Standard RC is not appropriate for this purpose. Praktika T-02(K) turnstile...
- Page 35 2. Block diagram of ACS using card collector Appendix Fig. 17. Block diagram №1 Figure 17 shows the most common connection circuit of card collector. OD can be controlled either by ACS controller or by the card collector directly, that is why connections 1* and 2* are drawn by dotted lines.
- Page 36 Memory of one of the controllers contains data on permanent card; memory of the second controller - on guest card. Reader transmits card code to both controllers and the card collector receives a corresponding signal depending on the type of card. Praktika T-02(K) turnstile...
- Page 37 Fig. 19 Block diagram №3 The block diagram #3 (Fig. 19) can be considered to be a logical development of the block diagram #2. It reduces the cost of installed system. For this purpose the controller with two output signals to one input of a reader (i.e., the controller can distinguish the guest cards and permanent cards transmitting a signal to the corresponding output) is used.
- Page 38 Appendix 3. Location of mounting holes in relation to the overall dimensions of the turnstile Fig. 20 Location of mounting holes in relation to the overall dimensions of the turnstile Praktika T-02(K) turnstile...
- Page 39 Installation guidelines...
- Page 40 OOO "Vozrozdenie" 192289 Saint Petersburg Sofiyskaya st., 66 Tel./fax +7 (812) 366 15 94 www.oxgard.com info@oxgard.com...
Need help?
Do you have a question about the Praktika T-02 and is the answer not in the manual?
Questions and answers