Related Manuals for Oxgard Praktika T-03-M
Summary of Contents for Oxgard Praktika T-03-M
- Page 1 MAINTENANCE OPERATIONS Praktika T-03-M(K) turnstile www.oxgard.com info@oxgard.com Tel.+7(812) 366-15-94...
-
Page 3: Table Of Contents
Contents 1. General information ................. 4 2. Conditions for maintenance ..............5 3. Partial disassemble of the turnstile............5 4. Checking turnstile parts ................12 5. Lubrication of moving parts ..............13 6. Assembling and operation checking of the turnstile ......16 Maintenance operations... -
Page 4: General Information
1.4. MO includes the following scope of work: partial disassemble of the turnstile, cleaning of load-bearing frame, checking of parts and units fixation, lubrication of subject to wear parts of actuating device, checking of belt tension, setting the dismantled parts and a general inspection of the turnstile. Praktika T-03-M(K) turnstile... -
Page 5: Conditions For Maintenance
2. Conditions for maintenance CAUTION! It is strictly forbidden to carry out work with powered turnstile. Failure to follow these safety requirements could result in damage to human life and health, total or partial loss of product workability and (or) auxiliary equipment. CAUTION! Do not remove motherboard located under the display panel. - Page 6 • remove the screw fixing the LED panel with a crosshead screwdriver (Fig. 3); • slide the display panel tin the direction indicated in Fig. 4, and lift it • Disconnect the cable from the LED panel. Praktika T-03-M(K) turnstile...
- Page 7 Fig. 2 Central stand of turnstile Fig. 3 Maintenance operations...
- Page 8 Fig. 5. Arm shall be rotating freely about the short axis. Fold the second arm in the same manner by turning the disc. The result is shown in Fig. 6. Praktika T-03-M(K) turnstile...
- Page 9 Fig. 5 Central stand of turnstile Fig. 6 Central stand of turnstile Maintenance operations...
- Page 10 Fig. 7 Central stand of turnstile Fig. 8 Central stand of turnstile Praktika T-03-M(K) turnstile...
- Page 11 3.5. Removing the lower panel of turnstile: • Remove two M6 DIN7985 screws (Fig. 7); • Remove M6 GOST11738-84 screw (Fig. 8); • Remove the lower cover by moving it vertically down, as shown in Fig. Fig. 9 Central stand of turnstile Maintenance operations...
-
Page 12: Checking Turnstile Parts
4.3. If necessary check and tighten the screw joints of turnstile: 4.4. Check the condition of the toothed belt and its tension (Fig. 10). 4.5. Check the general condition of the rubber plate stopper unit (Fig. 10). Fig. 10 Central stand of turnstile Praktika T-03-M(K) turnstile... -
Page 13: Lubrication Of Moving Parts
5. Lubrication of moving parts Lubrication is made with 2 - 3 drops of engine oil (viscosity grade 5W-20). 5.1. The rotation axis of the stopper unit (Fig. 11). 5.2. The rotation axis of the roller lever (Fig. 12). 5.3. Clip between the stopper unit and the solenoid (Fig. 13). Elements of the unit are located behind the roller lever shown on Fig. - Page 14 Fig. 12 Central stand of turnstile Fig. 13 Central stand of turnstile Praktika T-03-M(K) turnstile...
- Page 15 Fig. 14 Central stand of turnstile Fig. 15 Central stand of turnstile Maintenance operations...
-
Page 16: Assembling And Operation Checking Of The Turnstile
6.3. Reassemble the turnstile in reverse order. 6.4. Turn on the turnstile and perform functionality check by making several passes and activating “antipanic” mode. 6.5. If there is no extraneous noise or any abnormality in the turnstile work it is ready for operation. Praktika T-03-M(K) turnstile... - Page 17 Maintenance operations...
- Page 18 Praktika T-03-M(K) turnstile...
- Page 19 Maintenance operations...
- Page 20 OOO "Vozrozdenie" 192289 Saint Petersburg Sofiyskaya st., 66 Tel./fax +7 (812) 366 15 94 www.oxgard.com info@oxgard.com...
Need help?
Do you have a question about the Praktika T-03-M and is the answer not in the manual?
Questions and answers