Grizzly G0813 Owner's Manual
  1. Manuals
  2. Brands
  3. Grizzly Manuals
  4. Power Tool
  5. G0813
  6. Owner's manual

Grizzly G0813 Owner's Manual

6" jointer
Hide thumbs Also See for G0813:
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL G0813/G0814/G0814X
6" JOINTER
OWNER'S MANUAL
(For models manufactured since 10/19)
COPYRIGHT © MARCH, 2016 BY GRIZZLY INDUSTRIAL, INC. REVISED NOVEMBER, 2019 (MN)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
V2.11.19
#BL18046 PRINTED IN TAIWAN

Advertisement

Table of Contents
loading

Related Manuals for Grizzly G0813

Summary of Contents for Grizzly G0813

  • Page 1 OWNER'S MANUAL (For models manufactured since 10/19) COPYRIGHT © MARCH, 2016 BY GRIZZLY INDUSTRIAL, INC. REVISED NOVEMBER, 2019 (MN) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
  • Page 2 This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.

  • Page 3: Table Of Contents

    Cleaning & Protecting ........44 Identification ........... 3 Lubrication ........... 45 Controls & Components ......... 4 G0813 Machine Data Sheet ......6 SECTION 7: SERVICE ........46 G0814 Machine Data Sheet ......8 Troubleshooting ........... 46 G0814X Machine Data Sheet ...... 10 Setting/Replacing Knives (G0813/G0814) ..

  • Page 4: Introduction

    Machine Differences and it helps us determine if updated documenta- tion is available for your machine. Models G0813, G0814, and G0814X are 1 HP, 6" jointers with the following differences: Model G0813 has a 3-knife cutterhead and a •...

  • Page 5: Identification

    Always use hold-down or push blocks when jointing material narrower than 3" or surface planing material thinner than 3". e) Never perform jointing, planing, or rabbeting cuts on pieces shorter than 8" in length. Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 6: Controls & Components

    G. Outfeed Table: Supports workpiece after key to disable switch. it passes over cutterhead. For safety and best results, outfeed table must be properly adjusted relative to cutterhead knives/inserts before ANY operations (refer to Page 51 for more details). Model G0813/G0814/G0814X (Mfd. Since 10/19)
  • Page 7 O. 45° Fence Stop: Stops fence at 45° outward (135°). Note: Even when fence is resting against stops, tilt lock must be tightened before start- ing machine. P. Fence Tilt Lock: Secures fence tilt setting at desired angle. Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 8: G0813 Machine Data Sheet

    MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0813 6" X 48" JOINTER WITH ECONOMY STAND Product Dimensions: Weight................................247 lbs. Width (side-to-side) x Depth (front-to-back) x Height..............47-1/2 x 20 x 42 in.
  • Page 9 The information contained herein is deemed accurate as of 11/26/2019 and represents our most recent product specifications. Model G0813 PAGE 2 OF 3 Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 10: G0814 Machine Data Sheet

    The information contained herein is deemed accurate as of 11/26/2019 and represents our most recent product specifications. Model G0814 PAGE 1 OF 3 Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. Model G0813/G0814/G0814X (Mfd. Since 10/19)
  • Page 11 The information contained herein is deemed accurate as of 11/26/2019 and represents our most recent product specifications. Model G0814 PAGE 2 OF 3 Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 12: G0814X Machine Data Sheet

    The information contained herein is deemed accurate as of 10/22/2019 and represents our most recent product specifications. Model G0814X PAGE 1 OF 3 Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. -10- Model G0813/G0814/G0814X (Mfd. Since 10/19)
  • Page 13 The information contained herein is deemed accurate as of 11/11/2019 and represents our most recent product specifications. Model G0814X PAGE 2 OF 3 Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. -11- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 14: Section 1: Safety

    Never operate under the influence of drugs or injury or blindness from flying particles. Everyday alcohol, when tired, or when distracted. eyeglasses are NOT approved safety glasses. -12- Model G0813/G0814/G0814X (Mfd. Since 10/19)
  • Page 15 Make sure they are properly installed, you experience difficulties performing the intend- undamaged, and working correctly BEFORE ed operation, stop using the machine! Contact our operating machine. Technical Support at (570) 546-9663. -13- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 16: Additional Safety For Jointers

    Straight knives should never project MAXIMUM CUTTING DEPTH. To reduce risk of more than ⁄ " (0.125") from cutterhead body. kickback, never cut deeper than ⁄ " per pass. -14- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 17: Section 2: Power Supply

    Nominal Voltage ..208V, 220V, 230V, 240V meets the specified circuit requirements. Cycle ............60 Hz Phase ........... Single-Phase Power Supply Circuit ......15 Amps Plug/Receptacle ......NEMA 6-15 -15- Model G0813/G0814/G0814X (Mfd. Since 10/19)
  • Page 18 The plug must only be inserted into a matching receptacle (see following figure) that is properly installed and grounded in accordance with all local codes and ordinances. -16- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 19: Voltage Conversion To 220V

    Wire Cutters/Stripper ........1 instructions are not available, NEMA stan- dard 6-15 plug wiring is provided on Page 60. To convert Model G0813/G0814 to 220V: DISCONNECT MACHINE FROM POWER! Cut off existing 5-15 plug. Open motor junction box, remove two wire nuts indicated in Figure 7, then disconnect wires.

  • Page 20: Section 3: Setup

    IMPORTANT: Save all packaging materials until you are completely satisfied with the machine and No list of safety guidelines can be com- have resolved any issues between Grizzly or the plete. Every shop environment is different. shipping agent. You MUST have the original pack- Always consider safety first, as it applies aging to file a freight claim.

  • Page 21: G0813 Inventory

    "-18 x 2 ⁄ " (Belt Guard) ... 1 • Flat Washer ⁄ " (Belt Guard) ..... 1 • Flange Screws #10-24 x ⁄ " (Dust Port) ..4 Figure 10. Additional component inventory. -19- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 22: G0814/G0814X Inventory

    ⁄ "-18 x 2 ⁄ " (Belt Guard) ... 1 • Flat Washer ⁄ " (Belt Guard) ..... 1 • Flange Screws #10-24 x ⁄ " (Dust Port) ..4 Figure 11. Component inventory. -20- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 23: Hardware Recognition Chart

    Hardware Recognition Chart USE THIS CHART TO MATCH UP HARDWARE DURING THE INVENTORY AND ASSEMBLY PROCESS. Flat Head Screw -21- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 24: Cleanup

    Figure 13. T23692 Orange Power Degreaser. Repeat Steps 2–3 as necessary until clean, then coat all unpainted surfaces with a quality metal protectant to prevent rust. -22- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 25: Site Considerations

    Only install in an Shadows, glare, or strobe effects that may distract access restricted location. or impede the operator must be eliminated. Wall Min. 30" for Maintenance " 20" = Electrical Connection Figure 14. Minimum working clearances. -23- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 26: Assembly

    The Model G0813 jointer stand must be assem- Plate bled. The Model G0814/G0814X stand requires no assembly. Therefore, if assembling the Model G0813, start at Step 1. If assembling the Model Chute G0814/G0814X, start at Step 18 on Page 27. Support...
  • Page 27 #10-24 x ⁄ " flange screws (see Switch Figure 21). Front Panel Motor Cord Figure 19. Front and rear panels attached to corner supports. Switch Box Figure 21. Switch box attached to front panel. -25- Model G0813/G0814/G0814X (Mfd. Since 10/19)
  • Page 28 When strain relief is properly tightened, cord will not move inside junction box. Figure 26. Mobile base chassis attached to stand. 13. Re-install junction box cover. -26- Model G0813/G0814/G0814X (Mfd. Since 10/19)
  • Page 29 Figure 29. Checking belt alignment. 21. Remove rear panel to access mounting holes in stand during next step. Cutterhead Pulley Alignment Motor Pulley Figure 30. Pulley alignment. -27- Model G0813/G0814/G0814X (Mfd. Since 10/19)
  • Page 30 (see Figure 33). Fence Carriage Belt Base Bottom View Fence Lock Figure 35. Fence assembly installed onto Figure 33. Belt installed onto cutterhead and carriage base and secured with fence lock. motor pulleys. -28- Model G0813/G0814/G0814X (Mfd. Since 10/19)
  • Page 31 (TDC) (refer to Setting Outfeed Table Height on Figure 37. Set screw threaded into end of Page 51) and all knives/inserts are securely cutterhead guard shaft. tightened in cutterhead. -29- Model G0813/G0814/G0814X (Mfd. Since 10/19)
  • Page 32 36. G0813/G0814 Only: Assemble knife-setting gauge, as shown in Figure 39. Cutterhead guard must always return to closed position whenever it is moved. If it does not do this, it must be re-adjusted or re-installed. 34. Test operation of guard by pulling it back.

  • Page 33: Dust Collection

    The motor should run smoothly and without unusual problems or noises. Figure 41. Example of dust hose attached to dust port. Tug hose to make sure it does not come off. Note: A tight fit is necessary for proper performance. -31- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 34: Recommended Adjustments

    — If the machine does start, immediately stop Table Parallelism (Page 57). the machine. The switch disabling feature is not working correctly. This safety fea- ture must work properly before proceeding with regular operations. Call Tech Support for help. -32- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 35: Section 4: Operations

    Read books/magazines or get formal training before beginning any proj- ects. Regardless of the content in this sec- tion, Grizzly Industrial will not be held liable for accidents caused by lack of training. -33- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 36: Stock Inspection & Requirements

    1" Min. paint, or products that contain asbestos. Cutting these may lead to injury or machine damage. Figure 44. Minimum stock dimensions for jointer. Surface Planing -34- Model G0813/G0814/G0814X (Mfd. Since 10/19) 10" Min.

  • Page 37: Setting Depth Of Cut

    Figure 47. Scale Jam Nut Figure 47. Depth-of-cut scale components. Infeed Table Infeed Table Lock Lever Figure 45. Infeed table controls located on back of machine. -35- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 38: Squaring Stock

    Surface Plane on a Thickness Planer— Opposite face of workpiece is surface planed Previously flat with a thickness planer. Jointed Edge Previously Surface Planed Face -36- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 39: Surface Planing

    Tip: When squaring up stock, cut opposite side of workpiece with a planer instead of the jointer to ensure boths sides are parallel. Removed Surface Figure 48. Example photo of a surface planing operation. -37- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 40: Edge Jointing

    Tip: When squaring up stock, cut opposite Figure 49. Example photo of an edge jointing edge of workpiece with a table saw instead operation. of the jointer—otherwise, both edges of work- piece will not be parallel with each other. -38- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 41: Bevel Cutting

    4" from moving cutterhead at any time during operation! Repeat cutting process, as necessary, until Removed you are satisfied with the results. Surface Figure 50. Example photo of fence setup for a bevel cut of 45°. -39- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 42: Rabbet Cutting

    However, it is possible to make rabbet cuts with workpieces up to 1" thick without removing the cutterhead guard. This is done by performing the rabbet cut with the workpiece on end (similar to when you are edge jointing). -40- Model G0813/G0814/G0814X (Mfd. Since 10/19)
  • Page 43 Re-install cutterhead guard if removed in Start jointer. Step 3. Place workpiece firmly against fence and infeed table. CAUTION: To ensure workpiece remains stable during cut, concave sides of workpiece must face toward table and fence. -41- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 44: Section 5: Accessories

    T20503—Face Shield Window serious personal injury or machine damage. T20451—“Kirova” Clear Safety Glasses To reduce this risk, only install accessories T20452—“Kirova” Anti-Reflective S. Glasses recommended for this machine by Grizzly. T20456—DAKURA Safety Glasses, Black/Clear NOTICE T20502 T20452 Refer to our website or latest catalog for additional recommended accessories.
  • Page 45 Figure 59. G6697 Replacement Knives for Models G0813/G0814. Figure 57. Instructional reference book. www.grizzly.com 1-800-523-4777 order online at or call -43- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 46: Section 6: Maintenance

    Any other unsafe condition. Monthly Check V-belt tension, damage, or wear (Page 55). • • Clean/vacuum dust buildup from inside cabi- net and off motor. Figure 60. Recommended products for protecting unpainted cast-iron and steel. -44- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 47: Lubrication

    Lubrication Table Ways Oil Type ..Grizzly T23962 or ISO 68 Equivalent Oil Amount ...........1–2 Drops Lubrication Frequency ....... As Needed Since all bearings are sealed and permanently lubricated, simply leave them alone until they Lower infeed and outfeed tables to access ways.

  • Page 48: Section 7: Service

    (Pages 48 & 50). 7. Cutterhead bearings at fault. 7. Replace bearing(s)/realign cutterhead. 8. Centrifugal switch at fault. 8. Replace. 9. Motor bearings at fault. 9. Test by rotating shaft; rotational grinding/loose shaft requires bearing replacement. -46- Model G0813/G0814/G0814X (Mfd. Since 10/19)
  • Page 49 2. Workpiece too uneven at start of operation. 2. Take partial cuts to remove extreme high spots before doing a full pass. 3. Check/Adjust table parallelism (Page 57). 3. Outfeed table not parallel with infeed table. -47- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 50: Setting/Replacing Knives (G0813/G0814)

    Precision Straightedge or Knife-Setting Jig ..1 need to be adjusted (refer to Setting/ Hex Wrench 3mm ..........1 Replacing Knives on Page 49). Open-End Wrench 8mm........1 -48- Model G0813/G0814/G0814X (Mfd. Since 10/19)
  • Page 51 Using a hex wrench, rotate jack screws -49- Model G0813/G0814/G0814X (Mfd. Since 10/19) to raise or lower knife. When knife is set cor- — If jig does not sit as described, then that rectly, it will barely touch middle pad of knife knife must be reset.

  • Page 52: Rotating/Replacing Helical Cutterhead Inserts (G0814X)

    11. Replace cutterhead guard and cabinet rear access panel. Remove cover to get access to cutterhead pulley. Taking care not to pinch your hand between belt and pulley, rotate pulley as needed to make inserts accessible for removal. -50- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 53: Setting Outfeed Table Height

    IMPORTANT: This step is critical for achiev- ing a smooth finish with cutting operations. G0813/G0814 Only: Make sure knife heights Dirt or dust trapped under insert during instal- are set correctly (refer to Setting/Replacing lation will slightly raise insert in cutterhead, Knives on Page 48).

  • Page 54: Calibrating Depth Scale

    Outfeed Infeed Tighten outfeed table lock so outfeed table will not move during operation. Figure 77. Infeed table adjusted even with Re-install cutterhead guard, fence, and outfeed table. cabinet rear access panel. -52- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 55: Adjusting Gibs

    Note: Tighter gibs reduce play but make it harder to adjust tables. Repeat Steps 1-3 with outfeed table. Set outfeed table height as described in Setting Outfeed Table Height on Page 51. -53- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 56: Setting Fence Stops

    Loosen jam nut on 90˚ fence stop bolt (see Figure 81). Retighten jam nut loosened in Step 3. Adjust the 90˚ fence stop bolt until it makes contact with 90˚ swing stop. Retighten jam nut loosened in Step 3. -54- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 57: Tensioning/Replacing V-Belt

    Follow Steps 4–5 in Tensioning Belt proce- Press down on motor to keep tension on belt. dure to set correct belt tension. Tighten motor mount fasteners (see Figure 84), and replace cabinet rear access panel and belt guard. -55- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 58: Aligning Pulleys

    (see Figure 87). edge available that will fit; however, the most accurate results will come from using a straightedge. Pulley Figure 87. Motor pulley set screw locations. Replace cabinet rear access panel and belt guard. -56- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 59: Checking/Adjusting Table Parallelism

    Figure 90. Typical locations to place shims when Straightedge adjusting table parallelism. Outfeed Infeed Re-check outfeed table height (refer to Setting Outfeed Table Height), and re-ad- just if necessary. Figure 88. Checking table parallelism. -57- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 60: Section 8: Wiring

    Technical Support at (570) 546-9663. The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com. -58- Model G0813/G0814/G0814X (Mfd. Since 10/19)

  • Page 61: Wiring Diagram

    (Viewed from Behind) KEDU HY-18 20/12A 125/250V Figure 92. ON/OFF switch wiring (viewed from behind). Ground Motor Junction Box MOTOR Start Capacitor 300MFD 125VAC Figure 91. Motor junction box. READ ELECTRICAL SAFETY -59- Model G0813/G0814/G0814X (Mfd. Since 10/19) ON PAGE 58!

  • Page 62: Wiring Diagram

    (Viewed from Behind) KEDU HY-18 20/12A 125/250V Indicates wiring changes for 220V conversion Ground Motor Junction Box MOTOR Start Capacitor Figure 93. ON/OFF switch wiring 300MFD (viewed from behind). 125VAC READ ELECTRICAL SAFETY -60- Model G0813/G0814/G0814X (Mfd. Since 10/19) ON PAGE 58!

  • Page 63: Section 9: Parts

    SECTION 9: PARTS We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown are available for purchase. Call (800) 523-4777 or visit www.grizzly.com/parts to check for availability. Table 28 26 BUY PARTS ONLINE AT GRIZZLY.COM! -61- Model G0813/G0814/G0814X (Mfd.
  • Page 64 CAP SCREW 5/16-18 X 1 P0813059 PIVOT SHAFT 12.5 X 180MM P0813026 DEPTH-OF-CUT SCALE P0813060 E-CLIP 12MM P0813027 POINTER P0813061 HEX NUT 1/2-12 BUY PARTS ONLINE AT GRIZZLY.COM! -62- Model G0813/G0814/G0814X (Mfd. Since 10/19) Scan QR code to visit our Parts Store.

  • Page 65: Fence

    ROLL PIN 4 X 12 P0813132 HEX NUT 1/2-20 P0813117 SHOULDER BOLT 5/16-18 X 3/8, 1/4 X 3/8 P0813133 FLAT WASHER 1/2 BUY PARTS ONLINE AT GRIZZLY.COM! -63- Model G0813/G0814/G0814X (Mfd. Since 10/19) Scan QR code to visit our Parts Store.

  • Page 66: Cutterhead

    P0813220 KNIFE-SETTING JIG SHAFT P0813209 BEARING BLOCK (LEFT) P0814X221 T-HANDLE TORX DRIVER 1/4" P0813210 BALL BEARING 6202-2RS P0814X222 T-20 TORX BIT BUY PARTS ONLINE AT GRIZZLY.COM! -64- Model G0813/G0814/G0814X (Mfd. Since 10/19) Scan QR code to visit our Parts Store.

  • Page 67: G0813 Stand

    G0813 Stand 366 365 320-3 320-2 320-1 320-4 360A 320-5 320-9 320-8 320-7 320-6 320-10 BUY PARTS ONLINE AT GRIZZLY.COM! -65- Model G0813/G0814/G0814X (Mfd. Since 10/19) Scan QR code to visit our Parts Store.
  • Page 68 MOTOR CORD 16G 3W 31" P0813330 FLANGE SCREW 10-24 X 3/8 P0813391 REAR PANEL P0813334 DUST PORT 4" P0813393 HEX BOLT 3/8-16 X 1 BUY PARTS ONLINE AT GRIZZLY.COM! -66- Model G0813/G0814/G0814X (Mfd. Since 10/19) Scan QR code to visit our Parts Store.

  • Page 69: G0814/G0814X Stand

    G0814/G0814X Stand 366 365 360A 320-3 320-2 320-1 320-4 320-5 320-9 320-8 320-7 320-6 320-10 BUY PARTS ONLINE AT GRIZZLY.COM! -67- Model G0813/G0814/G0814X (Mfd. Since 10/19) Scan QR code to visit our Parts Store.
  • Page 70 DUST PORT 4" P0814390 MOTOR CORD 16G 3W 31" P0814338 WRENCH 8 X 10MM OPEN-ENDS P0814393 TAP SCREW #5 X 3/8 BUY PARTS ONLINE AT GRIZZLY.COM! -68- Model G0813/G0814/G0814X (Mfd. Since 10/19) Scan QR code to visit our Parts Store.

  • Page 71: G0813 Labels & Cosmetics

    Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com. BUY PARTS ONLINE AT GRIZZLY.COM! -69- Model G0813/G0814/G0814X (Mfd.

  • Page 72: G0814/G0814X Labels & Cosmetics

    Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com. BUY PARTS ONLINE AT GRIZZLY.COM! -70- Model G0813/G0814/G0814X (Mfd.

  • Page 73: Warranty & Returns

    WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.

This manual is also suitable for:

G0814G0814x

Table of Contents