Contents in Box Accessories (not included) Features Common Features Wireless Bluetooth® Technology Wireless DECT7 Communications Pick Your Headset (or Bluetooth Speaker) Wear or Mount Your Firecom Connect Charging LED Indications Settings & Operation Buttons Wireless Bluetooth® Pairing Wireless DECT7 Advanced Menu & Quick Launch...
Bluetooth® headset to plug or pair to Manual and Reference the Firecom Connect to communicate with their team up to 800 feet line of sight, 1 ea x Quick Start Guide hands-free. The Firecom Connect is rugged and rated at IP67, so it’s waterproof and 1 ea x Manual (online at: www.firecom.com)
Firecom Connect utilizes audible beeps for volume adjustments. Voice prompts are At a mere 3” x 3” x 1”, the Firecom Connect is discrete in size to be worn on your belt used for Advanced Menu navigation and setting selections.
Radio PTT button allows the Firecom Connect or headset to momentarily talk on any The Firecom Connect can be used in a variety of ways including being placed on a available slot. A tone will let the user know when they can talk. After talking, there dashboard or desk, worn on your belt with the included magnetic belt clip, clipped to will be a slight delay when other users cannot be heard.
The Firecom Connect uses a USB-C charging jack with the Firecom Connections shown below. Note: Prior to first use, make sure to charge your Firecom Connect to full charge. Vehicle Charging WARNING: Using unregulated wall adapters will damage the Firecom Connect Use the supplied USB-C charging cable and DC automotive charging adapter.
Beeps indicate the increase or decrease in the desired volume adjustments. Firecom Connect has up to nine volume level settings (Default level: 70% of max volume). Adjustments to the volume can also be made on the device paired or plugged into the Firecom Connect.
Out of Range Warning: using with the Firecom Connect “Forgets” these other devices. The easiest way to achieve this is to reset the headset. • If Firecom Connect has low radio signal (RSSI) to its Base Station it will report “DECT •...
Advanced Menu & Quick Launch The Advanced Menu is to set-up and configure the Firecom Connect for use. Caution Version ( "Version 1" must be taken with these adjustments, as they change the operational characteristics Indicates what firmware version your Firecom Connect is running.
• When the user presses the Radio PTT, any noise gate will be removed when in 7. If the Firecom Connect has a DECT connection and the Radio RSSI Reporting is set Radio VOX & Radio PTT modes. to ON, it will announce the signal strength every 5 seconds. If no DECT connection is present, the Firecom Connect will announce “No DECT”...
Base Station. Up to 5 channels are available through the Wireless Base Station when used in this configuration. Follow the steps below to configure your Base Now that your Base Station is set up in Channel Mode, your Firecom Connect Quick Station.
4. In File Manager Firecom Connect will appear as an extra drive (normally D :) Service Contact 5. Select ALL the files in the Firecom Connect D drive and delete all of them. 6. Drag and Drop or Copy and Paste ALL the update files you downloaded from...
Intercom and the Wireless Base Station. These 4. If DECT is not connected for 10 minutes, Firecom Connect will power down to save cables should be routed away from portable and mobile radios and antenna cabling battery.
15 seconds (this will restart the Firecom Connect). IC UPN Firecom Connect: 7895A-950140600 2. When Firecom Connect restarts, release the power button to boot normally. 3. If inadvertently enter bootloader (rapid red flashing after releasing power), press Bluetooth® Specifications Power for 2 seconds for normal restart.
Page 15
Humidity per MIL-STD 810F and 810G Temperature Shock per MIL-STD 810F and 810G Chemical Exposure per MIL-STD 810 Salt Spray per J1455, Sec. 4.3 Vibration per J1455, Sec. 4.9 Conducted Immunity per J1113-11 Electrostatic Discharge per J1113-13 Radiated Emissions per J1113-41 Conducted Transients per 7637-2 Quality Management System ISO 9001:2008 13 |...
RSS standard(s). The Firecom Connect water and dust egress IP rating does not apply when the Operation is subject to the following two conditions: battery door is open. DO NOT expose this unit to rain or moisture if unit is open.
FCC or IC RF exposure guidelines. Before placing the Firecom Connect in the charger, make sure the battery is • This product may not be co-located or operated in conjunction with any other installed and the battery cover is securely in place.