Table Of Contents; Product Specifications Kn M-2504Rc; Symbols - KNOVA KN M-2504RC Manual

TABLE OF CONTENTS

Table of contents ............................................................... 1
Product specifications KN M-2504RC ................................ 1
Symbols .............................................................................. 1
Power tool safety ................................................................ 2
Table saw safety ................................................................. 3
Electrical requirements and safety ...................................... 4
Accessories and attachments ............................................. 5
Tools needed for assembly ................................................. 5
Carton contents .................................................................. 5
Know your table saw .......................................................... 7
Glossary of terms ..............................................................

PRODUCT SPECIFICATIONS KN M-2504RC

MOTOR
Type: Universal
Amperes: 15 Amp
Voltage: 120 V AC
Hz: 60 Hz
RPM (no load): 5 000 RPM (no load)
Overload Yes
protection:
WARNING
To avoid electrical hazards, fire hazards or damage to the tool, use proper circuit protection. This tool is wired
at the factory for 110-120 Volt operation. It must be connected to a 110-120 Volt / 15 Ampere time delay fuse or circuit
breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any way. Before using your tool,
it is critical that you read and understand these safety rules. Failure to follow these rules could result in serious injury to you or
damage to the tool.
PLEASE READ THE FOLLOWING: The manufacturer and/or distributor is providing the buyer with a parts list and assembly diagram
in this manual as a reference tool only. Neither the manufacturer nor distributor make any representation or warranty of any kind to
the buyer regarding the accuracy of the list or diagram or that buyer is qualified and able to make any repairs or replace any parts of
the product. The manufacturer and/or distributor expressly recommend: that all repairs and/or part replacements only be undertaken
by a certified and licensed technician, and not by the buyer. The buyer assumes all risk and liability, including injuries to persons and
damage to property, associated with and arising out of any attempt of the buyer at repairs or replacement of parts to the product.

SYMBOLS

WARNING ICONS
Your power tool and its Operator's Manual may contain "WARNING ICONS" (a picture symbol intended to alert you to, and/or
instruct you how to avoid, a potentially hazardous condition). Understanding and heeding these symbols will help you operate your
tool better a. safer. Shown below are some of the symbols you may see.
SAFETY ALERT: Precautions that involve your safety.
PROHIBITION
WEAR EYE PROTECTION: Always wear safety
goggles or safety glasses with side shields.
WEAR RESPIRATOR AND HEARING PROTECTION:
Always wear respiratory and hearing protection.
READ AND UNDERTAND INSTRUCTION MANUAL:
To reduce the risk of injury, user and all bystanders
must read and understand
using this product.
KEEP HANDS AWAY FROM BLADE: Failure to keep
your hands away from the blade will result in serious
personal injury.
BLADE SIZE
Diameter:
Arbor size: 5/8 in.
SAW
Rip fence: Yes
Miter gauge: Yes
Rip capacity: 8-1/2 in. left,
24 in. right
before
Operator's Manual
Assembly ...........................................................................
Adjustment ........................................................................ 14
Operation ........................................................................... 17
Maintenance ...................................................................... 22
Troubleshooting guide ........................................................ 24
Push stick construction ...................................................... 25
Parts list ............................................................................. 26
Schematic .......................................................................... 28
Parts list and schematic (motor) ........................................ 29
Parts list and schematic (stand) ........................................ 30
8
CUTTING CAPACITY
Maximum cut depth at 90º: 3 in.
10 in.
Maximum cut depth at 45º: 2-1/2 in.
Maximum diameter dado:
Maximum dado cut width:
SUPPORT AND CLAMP WORK
DANGER
DANGER: Indicates an imminently
hazardous situation which, if not avoided, will result
in death or serious injury.
WARNING
WARNING: Indicates a potentially
hazardous situation which, if not avoided, could result
in dead or serious injury.
CAUTION
CAUTION: Indicates a potentially hazardous
situation which, if not avoided, may result in minor or
moderate injury.
CAUTION
CAUTION: Used without the safety alert
symbol indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
1
8
6 in.
(stackable only)
1/2 in.