Related Manuals for Raven SmarTrax John Deere 8R 2009 Series
Summary of Contents for Raven SmarTrax John Deere 8R 2009 Series
- Page 1 SmarTrax™ Installation Manual John Deere 8R-Series - Steering Ready Model Year 2009-2010...
- Page 2 GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the accuracy, integrity, continuity, or availability of these services and cannot guarantee the ability to use Raven systems, or products used as components of systems, which rely upon the reception of these signals or availability of these services.
-
Page 3: Table Of Contents
Table of Contents Chapter 1 Important Safety Information..........1 Hydraulic Safety ........................2 Electrical Safety ........................2 Chapter 2 Introduction................3 Preparing for Installation ......................3 Recommendations ......................4 Point of Reference ....................... 4 Updates ............................. 4 Kit Contents ..........................5 Chapter 3 Cab Component Installation .......... - Page 4 Table of Contents John Deere 8R-Series - Steering Ready (Model Year 2009-2010) SmarTrax™ Installation Manual...
-
Page 5: Important Safety Information
• Follow all safety information presented within this manual. • If you require assistance with any portion of the installation or service of your Raven equipment, contact your local Raven dealer for support. • Follow all safety labels affixed to the SmarTrax system components. Be sure to keep safety labels in good condition and replace any missing or damaged labels. -
Page 6: Hydraulic Safety
CAUTION Hydraulic Safety • Raven Industries recommends that appropriate protective equipment be worn at all times when working on the hydraulic system. • Never attempt to open or work on a hydraulic system with the equipment running. Care should always be taken when opening a system that has been previously pressurized. -
Page 7: Introduction
I ntroduction CHAPTER C h a p t e r 2 Congratulations on your purchase of the SmarTrax system! This system is designed to provide cutting-edge, hands-free steering of the machine via Global Positioning System (GPS) coordinates. This manual applies to the following machines: MAKE: John Deere MODEL: 8225R, 8245R, 8270R, 8295R, 8320R and 8345R - Steering Ready YEAR: 2009-2010... -
Page 8: Recommendations
Software and manual updates are available on the Raven Applied Technology website: http://www.ravenhelp.com At Raven Industries, we strive to make your experience with our products as rewarding as possible. One way to improve this experience is to provide us with feedback on this manual. -
Page 9: Kit Contents
This section contains a list of the components that are included in the SmarTrax kit. Before beginning the SmarTrax installation, compare the items in the kit with the components on this list. If you have questions about the kit, contact your Raven dealer. SmarTrax Installation Kit (P/N 117-5034-013) TABLE 1. - Page 10 Chapter 2 SmarTrax Installation Kit (P/N 117-5034-013) TABLE 1. Picture Item Description Part Number Qty. Terminator - John Deere 8R-Series Wheel 063-4001-006 Angle Sensor (WAS) Tape - 3.5” Double-Sided 332-0000-019 Nut - 3/8”-16 Nylon Insert Lock 312-4001-109 John Deere 8R-Series - Steering Ready (Model Year 2009-2010) SmarTrax™ Installation Manual...
-
Page 11: Cab Component Installation
C ab Component CHAPTER C h a p t e r 3 Installation Install the SmarTrax Node Mount the SmarTrax Node SmarTrax Node Installed FIGURE 1. Mount the SmarTrax node (P/N 063-0173-228) on the node mounting bracket (P/N 107-0172-055) using three 3/8”-16 nylon insert lock nuts (P/N 312-4001-109). -
Page 12: Node Mounting Locations
Chapter 3 Node Mounting Locations Node Mounting FIGURE 2. Direction Arrows Any two arrows must be parallel with level ground Mounting Tabs When choosing the location for the SmarTrax node, consider the following points: • Mount the SmarTrax node inside the machine’s cab on a flat, level surface for proper performance and cable connection. -
Page 13: Connect To The Steering Wheel Encoder
Cab Component Installation Connect to the Steering Wheel Encoder Steering Column Shroud Removed FIGURE 3. Remove the shroud surrounding the steering column. Encoder Connections FIGURE 4. Locate and disconnect the machine’s two encoder connections. Route the STEERING WHEEL ENCODER connector from the node harness (P/N 115-4001-087) into one of the machine’s mating encoder connectors. -
Page 14: Install The Foot Switch
Chapter 3 Encoder Terminator FIGURE 5. Install the two encoder terminators (P/N 063-4001-003) on the machine’s cables that were disconnected from the encoder. Install the Foot Switch Foot Switch Installed FIGURE 6. Select a suitable location for the foot switch (P/N 063-0172-470) to be installed. Note: The foot switch should be installed in a location where the operator has easy access to it and is able to fully press the pedal. -
Page 15: Install The Valve Harness
Cab Component Installation Install the Valve Harness Cab Floor Access Plate Removed FIGURE 7. Lift the floor mat just inside the door. Remove the cab floor access plate. Cut a notch (approximately 1” x 1”) into the cab floor access plate. From outside the cab, route the 12-pin connector of the valve harness (P/N 115-4001-156) into the cab through the access hole in the floor. - Page 16 Chapter 3 Machine’s Configuration FIGURE 9. Flow Meter Wheel Angle Sensor Connection Determine whether the machine has a wheel angle sensor (WAS) or a flow meter installed. • WAS - Trace the WAS cable from the front-left kingpin. Locate and disconnect the 8-pin WAS connection on the left side of the tractor, then connect the WHEEL ANGLE SENSOR connector on the valve harness to the machine’s WAS connector.
- Page 17 Cab Component Installation Valve Harness Wiring Diagram FIGURE 10. Manual No. 016-5034-013 Rev. B...
-
Page 18: Install The Chassis Cable - Smartrax-Only Systems (If Applicable)
The SmarTrax interface tee is sold separately. Contact your local Raven dealer for ordering information. Locate and disconnect the connection between the Raven console cable and chassis cable on the machine’s existing CAN system. Install the SmarTrax interface tee cable (P/N 115-4001-070 or 115-4001-071) between the chassis and Raven console harness. -
Page 19: System Diagrams
Cab Component Installation System Diagrams Existing Chassis System Wiring Diagram FIGURE 11. Manual No. 016-5034-013 Rev. B... - Page 20 Chapter 3 Envizio Pro II SmarTrax with Slingshot FIGURE 12. John Deere 8R-Series - Steering Ready (Model Year 2009-2010) SmarTrax™ Installation Manual...
- Page 21 Cab Component Installation Envizio Pro/Viper Pro SmarTrax with Slingshot FIGURE 13. Manual No. 016-5034-013 Rev. B...
- Page 22 Chapter 3 Cruizer II RTK SmarTrax with Slingshot FIGURE 14. John Deere 8R-Series - Steering Ready (Model Year 2009-2010) SmarTrax™ Installation Manual...
-
Page 23: Startup Procedures
S tartup Procedures CHAPTER C h a p t e r 4 WARNING When starting the machine for the first time after installing SmarTrax, be sure that all persons stand clear in case a hose has not been properly tightened. WARNING Do not use hands to check for leaks. - Page 24 Chapter 4 John Deere 8R-Series - Steering Ready (Model Year 2009-2010) SmarTrax™ Installation Manual...
- Page 25 Index Cab Component Installation Connecting SmarTrax to an Existing Chassis Cable 14 Connecting to the Steering Wheel Encoder 9 Installing the Chassis Cable - SmarTrax-Only Systems 14 Installing the Foot Switch 10 Installing the SmarTrax Node Node Mounting Locations 8 Installing the Valve Harness 11 System Diagrams 15 Important Safety Information...
- Page 26 Index John Deere 8R-Series - Steering Ready (Model Year 2009-2010) SmarTrax™ Installation Manual...
- Page 27 How Can I Get Service? Bring the defective part and proof of purchase to your Raven dealer. If your dealer agrees with the warranty claim, the dealer will send the part and proof of purchase to their distributor or to Raven Industries for final approval.
- Page 28 Sioux Falls, SD 57117-5107 Fax: 605-331-0426 www.ravenprecision.com www.ravenhelp.com Notice: This document and the information provided are the property of Raven Industries, Inc. and may only be used as authorized by Raven Industries, Inc. All rights reserved under copyright laws. ©Raven Industries, Inc. 2012...