AES global Styluscom Video Manual

StylusCOM Video
* ALWAYS FULLY TEST THE UNIT ON SITE BEFORE INSTALLATION TO AVOID RESTOCKING FEES *
STYLUSCOM - WIRING DIAGRAM
PLEASE USE ADDITIONAL POWER
SUPPLY (NOT PROVIDED) FOR
DISTANCES GREATER THAN 130m.
CHECK FURTHER INFORMATION FOR
MAX MONITOR DISTANCES AND
POWER REQUIREMENTS, OR IF YOU
Pairing
NEED TO CHAIN MULTIPLE MONITORS
LEDs TOGETHER.
CONNECTIONS WILL GO TO GATE
CONTROLLER/DOOR LOCK ETC.
PLEASE SEE ADDITIONAL DIAGRAMS
FOR RELAY CONNECTIONS FOR THE
REQUIRED TYTPE.
(300m MAX DISTANCE)
PLEASE USE THE 24v POWERSUPPLY
PROVIDED WITH THE STYLUSCOM KIT.
Optional Programmable Keypad
THE AES KEYPAD IS AN OPTIONAL EXTRA.
IF KEYPAD PRESENT, PLEASE SEE THE
RELAY 1
KPX1200 GUIDE
' ' ON OUR WEBSITE
FOR FULL INSTRUCTIONS ON PROGRAMMING
AND EXTENSIVE FEATURES.
RELAY CONNECTIONS
N/ O Normally Open
C Common
N/ C Normally Closed
+ -
N.C. COM N.O. N.C. / N.O.
Power for keypad will come
RELAY 1 R2
24v IN
already pre-wired.
- Hardwired System
STATION 2
VID1+
VID1-
AUD1
MODEL: Stylus V2
GND
CMD1
SLAVE OUT
DATA
VIDEO
AUDIO
GND
300m MAX
DISTANCE
(SHIELDED CAT5)
RELAY 1
N/O
COM
N/C
GROUND
DA TA EG
I/O IN
EGRESS
TIP:
STATION 1
You must test to ensure that the system is capable of operating on the desired site.
VID1+
MODEL: Stylus V2 Power the system on and place the monitors in their expected locations around
VID1-
the property and then test that everything is working
AUD1 to the walls.
GND
OPTIMAL RANGE
CMD1
SLAVE IN
TIP:
DATA
separate power supply as close as possible to the video monitor. If chaining
multiple monitors together use the SLAVE inputs and outputs - see supplement
VIDEO
wiring diagram which will provide more information on the specific requirements
AUDIO
and max distances
GND
POWER CABLE
TIP:
24v to power the unit.
0v
Please use the following cable:
Up to 2 metres ( 6 feet )
Up to 4 metres ( 12 feet ) – Use minimum 0.75mm
Up to 8 metres ( 24 feet ) – Use minimum 1.0mm
N/ O
CALL STATION
NEED MORE ASSISTANCE?
PLEASE SCAN THIS QR CODE TO BE
BROUGHT TO OUR RESOURCES PAGE
WHERE YOU CAN FIND ALL OF OUR
GUIDES AND AVAILABLE RESOURCES.
Find all of our support options such as Web Chat,
Full Manuals, Customer Helpline and more on
SITE SURVEY RESTOCKING FEES MAY APPLY IF RETURNED AFTER INSTALL DUE TO SITE
ISSUES. PLEASE SEE FULL T&C'S ON OUR WEBSITE
It is recommended that the system be fully tested on site
To get the most range out of the system we would recommend keeping the
.
Most technical calls received are due to installers using CAT5 or alarm cable
NEITHER are rated to carry enough power! ( 1.2amp peak )
– Use minimum 0.5mm
MAGNETIC LOCK EXAMPLE
Follow this method when using a magnetic lock. If the relay in either the
| C | N/ C
Call Station or optional AES Keypad is triggered it will temporarily lose
power and allow the door/gate to release.
For installs without the optional AES Keypad; connect the
Magnetic Lock PSU to N/C terminal on Call Station Relay.
+
MAX 24 VOLTS!
-
POWER ADAPTER
EXIT
* MAGNETIC LOCK PSU SOLD SEPARATELY *
+
MAGNETIC LOCK
-
STILL HAVING TROUBLE?
our website:
WWW.AESGLOBALONLINE.COM
BEFORE installation.
BEFORE mounting any items
SHIELDED CABLE IS ALWAYS RECOMMENDED
KEEP POWER SUPPLY AS CLOSE AS POSSIBLE.
2 ( 18 gauge )
2
( 16 gauge )
2
( 14 / 16 gauge )
N/ C | C | N/ O
AES KEYPAD
POSITIVE of the
MAINS
POWER