Simrad CE33 ChartSounder Manual
  1. Manuals
  2. Brands
  3. Simrad Manuals
  4. Marine GPS System
  5. CE33 ChartSounder
  6. Manual
Simrad CE33 ChartSounder Manual

Simrad CE33 ChartSounder Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

M A N U A L
Simrad CE33
ChartSounder
183-2100-702
02181.11
Note!
Insert or remove C-MAP cartridges ONLY through CHART menu or when
unit is off. All electronic navigation equipment is subject to external factors
beyond the control of the manufacturer. Therefore such equipment must be
regarded as an aid to navigation. The prudent navigator will, for that reason,
never rely on a single source for position fixing and navigation.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CE33 ChartSounder and is the answer not in the manual?

Questions and answers

Related Manuals for Simrad CE33 ChartSounder

Summary of Contents for Simrad CE33 ChartSounder

  • Page 1 M A N U A L Simrad CE33 ChartSounder 183-2100-702 02181.11 Note! Insert or remove C-MAP cartridges ONLY through CHART menu or when unit is off. All electronic navigation equipment is subject to external factors beyond the control of the manufacturer. Therefore such equipment must be regarded as an aid to navigation.
  • Page 2 MOB ‘MAN OVERBOARD’ function In case someone falls overboard, press the [MOB] key and hold for 2 seconds (or activate an external MOB switch - hold for 5 seconds). Press [CLR] to confirm and reset the alarm if activated by mistake. Press [ENT] to make all relevant data available for an efficient rescue operation: MOB Page 1: The Chart 1 display will provide a graphical impres-...

  • Page 3: Table Of Contents

    CE33 ChartSounder Table of contents MOB ‘MAN OVERBOARD’ function ......back of front cover Chapter 1 Introduction and safety summary Introduction and system familiarization ........1-1 Safety summary ................1-2 How to get started ................ 1-3 1.3.1 Dedicated function keys ............... 1-3 1.3.2...
  • Page 4 Table of contents CE33 ChartSounder Speed, course & depth ..............4-6 Speed diagram................4-7 Satellite status................4-9 DGPS information...............4-11 SDGPS information..............4-13 4.7.1 Satellites in SDGPS system............4-15 Chapter 5 Waypoint / route menu Waypoint / route menu ..............5-1 Waypoints stored in the memory ..........5-1 5.1.1...
  • Page 5 Factory settings ................9-13 Chapter 10 Installation and service Installation and service .............. 10-1 10.1 Installation notes ................ 10-1 10.2 Installation of CE33 ChartSounder ..........10-3 10.3 Location for display unit ............10-4 10.4 Installation of DS33 Dual Station..........10-5 10.4.1 Operation of DS33 Dual Station..........
  • Page 6 Determining the position for the transducer ......10-13 10.9 Preventive maintenance.............10-15 10.10 Repair and service ..............10-15 10.11 Troubleshooting.................10-15 10.12 Specifications ................10-16 Appendix A Glossary of terms ..............A-1 Appendix B List of datum ................B-1 Appendix C C-MAP attributes..............C-1 Index Declarations of conformity International warranty List of Simrad distributors...

  • Page 7: Introduction And System Familiarization

    CE33 Introduction and safety summary Chapter 1-1 1.1 Introduction and system familiarization Congratulations on your purchase of SIMRAD CE33 ChartSounder - a combination of the latest GPS and SDGPS receiver technology and optional built-in differential receiver for accurate positioning, plus: detailed cartogra- phy and high performance echosounder;...

  • Page 8: Safety Summary

    Chapter 1-2 CE33 Introduction and safety summary give you a quick introduction to some of the features you have access to in your new chart sounder. The display examples shown in this manual are not always an exact copy of what you will see on the screen, as the presentation depends on your system configuration and choices of setup.

  • Page 9: How To Get Started

    CE33 Introduction and safety summary Chapter 1-3 1.3 How to get started Press and hold the [PWR] key until you have a picture on the screen Press the [ENT] key to accept warning when the system is ready Your present position will automatically be updated within a few minutes. When ready, the ship symbol on the chart will flash and the *** will be replaced by actual course and speed figures.

  • Page 10: Chart And Chart Functions

    Chapter 1-4 CE33 Introduction and safety summary 1.3.2 Chart and chart functions Press the [CHART] key to call Chart 1 and toggle data field or CHART echosounder split screen on/off - see chart examples in section 1.3.1. C-MAP cartridges (standby) Press [MENU], [1], [3] whenever inserting or removing a C-MAP card.
  • Page 11 CE33 Introduction and safety summary Chapter 1-5 How to plot or insert waypoints and marks • With cursor OFF (press [CLR]) Press [PLOT] and choose from: [PLOT] Plot ship’s position as an eventmark. You can insert new lat/lon figures and change the symbol’s size, type and color.
  • Page 12 Chapter 1-6 CE33 Introduction and safety summary How to edit a route - rubberbanding • To move a point: 1. Place cursor on the point you wish to move. 2. Press [ENT], [1], [2]. 3. Move cursor to new location. 4.

  • Page 13: Echosounder / Fishfinder

    CE33 Introduction and safety summary Chapter 1-7 Advance or stop navigation • Press [GOTO], [1] to advance to next point in the route. • Press [GOTO], [3] to stop navigation. Start and stop track 1. Press [MENU], [3], [5]. 2. Before tracking is started, you can give the track a new name, make changes to track interval, track line type and color.
  • Page 14 Chapter 1-8 CE33 Introduction and safety summary...

  • Page 15: Fundamentals Of The Display And

    CE33 Fundamentals & initial start-up Chapter 2-1 2.1 Fundamentals of the display and page system The CE33 ChartSounder has a multi-function screen and data pres- entation system with full screen or a split screen with chart and data. Full screen.
  • Page 16 Chapter 2-2 CE33 Fundamentals & initial start-up Toggle between the four pre-set pages manually: Press the [PAGE] key - again and again - to toggle between the 4 PAGE pre-set pages, which as default are: Chart 1 with info field, Position, Highway, Echo 200kHz displays.

  • Page 17: Key Functions

    CE33 Fundamentals & initial start-up Chapter 2-3 2.2 Key functions Some of the key functions are general and can be applied at any time, other key functions are related to a certain menu(s) and can only be applied when in the appropriate menu. Hotkey to Chart 1 display.

  • Page 18: Menu Bar

    Chapter 2-4 CE33 Fundamentals & initial start-up The alpha-numeric keys inserts and selects data in data displays. Keys 1-9 are also Quick-range keys, which each represent a fixed chart range or echosounder range. Key 0 will center the cursor/ship on the chart or activate auto range in sounder mode. Turns cursor off (and centers ship) on chart display.

  • Page 19: Menu Layout

    CE33 Fundamentals & initial start-up Chapter 2-5 list when empty, will have a different color (normally preset red) from the rest of the functions. The menu bar will disappear from the screen at the selection of a function, or by pressing the [MENU] key. Besides, if not used, it automatically turns off after 30 seconds.
  • Page 20 Chapter 2-6 CE33 Fundamentals & initial start-up PILOT When this PILOT menu appears, then Highway one of the Navigation modes is active. Turn NAV off WP advance Restart to approaching point ETA & AVN Trim & highway Set & drift SETUP When selecting a sub-menu in the SETUP menu, the display will always...

  • Page 21: Choice Of Symbols

    CE33 Fundamentals & initial start-up Chapter 2-7 2.5 Choice of symbols Waypoints and other points appearing on the screen can be marked by one of 18 symbols + 8 event marks in small or large symbols: 2.6 Naming of routes, points etc. First select the key with the desired letter, then you can either repeat the keystrokes, which will toggle between e.g.

  • Page 22: Turn Power Off

    Chapter 2-8 CE33 Fundamentals & initial start-up correct position without further data entries. The start-up phase is completed when a position appears in the position display - see sec- tion 4.1. The echosounder function has a demo program, which can be acti- vated in the Echosounder setup display, refer to section 7.8.

  • Page 23: Chart Menu

    CE33 Chart menu and INFO windows Chapter 3-1 3. Chart menu CHART - see section 3.1 Chart 1 1:26400000 - see section 3.1 Chart 2 1:6600000 - see section 3.2 C-MAP cartridge For safety reasons, navigation with electronic charts should always be combined with authorized paper charts.

  • Page 24: Data Field In Chart

    Chapter 3-2 CE33 Chart menu and INFO windows Chart range indicator (5.1nm) can be set ON/OFF in “Chart setup”. 3.1.1 Data field in chart The data field in the chart display (with cursor off) will give you the ship’s current speed, course and *position in lat/long together with water speed and depth indication.

  • Page 25: Cursor Function

    CE33 Chart menu and INFO windows Chapter 3-3 3.1.3 Cursor function With chart display active: Press the cursor key to activate the chart cursor (cross hairs) Press [CLR] to turn the chart cursor off The chart cursor will automatically switch off if not used in the last five minutes.
  • Page 26 Chapter 3-4 CE33 Chart menu and INFO windows level range is switched off and the chart changes to a new level of details. The extended level range can be toggled OFF/ON in chart setup (default = ON). See section 3.4 Chart setup. Chart details may not be available in all scales in all areas.

  • Page 27: C-Map Cartridge

    CE33 Chart menu and INFO windows Chapter 3-5 3.2 C-MAP cartridge On the unit’s front below the keypad is a watertight drawer wherein you place the C-MAP cartridge/C-card you wish to load. Do not attempt to insert or remove a cartridge unless the unit is turned off, or chart reading is in stand-by - see below.
  • Page 28 Chapter 3-6 CE33 Chart menu and INFO windows In addition to the larger boundaries of the world chart there will be separate boundary lines for the individual charts stored on the same cartridge. However, the boundary lines for the C-MAP chart areas can be turned off, so they will not be visible on the chart - refer to section 3.4 Chart setup.

  • Page 29: Info Windows

    CE33 Chart menu and INFO windows Chapter 3-7 3.3 INFO windows A number of pop-up INFO windows are available mainly from active chart display. Only a few of the functions in the INFO win- dows can be accessed from data displays and other displays. Refer to sections 3.3.x.

  • Page 30: Cursor Active But Not Placed On Any Object Or Data

    Chapter 3-8 CE33 Chart menu and INFO windows 3.3.2 Cursor active but not placed on any object or data With chart in active page, and cursor active but not placed on any object or user data, press [ENT] to call up an info window with the following to choose from - text in red are inactive functions: Scale: 1:6600000 Actual chart scale...

  • Page 31: Cursor Placed On Waypoint

    CE33 Chart menu and INFO windows Chapter 3-9 3.3.3 Cursor placed on waypoint With chart in active page, and cursor placed on a waypoint, press [ENT] to call up an info window with the following to choose from - text in red are inactive functions: WP found Name: WP 1 LAT 57°15.504N...

  • Page 32: Cursor Placed On Route Leg Or Line Section

    Chapter 3-10 CE33 Chart menu and INFO windows 3.3.4 Cursor placed on route leg or line section With chart in active page, and cursor placed on a route leg or line section, press [ENT] to call up an info window with the following to choose from: Route leg found: Name: RTE 1...

  • Page 33: Cursor Placed On Routepoint Or Linepoint

    CE33 Chart menu and INFO windows Chapter 3-11 3.3.5 Cursor placed on routepoint or linepoint With chart in active page, and cursor placed on a routepoint or line- point, press [ENT] to call up an info window with the following to choose from: Routepoint found Name: RTE 1...

  • Page 34: Cursor Placed On Trackpoint

    Chapter 3-12 CE33 Chart menu and INFO windows 3.3.6 Cursor placed on trackpoint Trackpoints are not as easily recognized as Routepoints, you may have to move the cursor along on the track to locate a trackpoint. With chart in active page, and cursor placed on a trackpoint, press [ENT] to call up an info window with the following to choose from: Trackpoint found Name: TRACK 1...

  • Page 35: Cursor Placed On Target

    CE33 Chart menu and INFO windows Chapter 3-13 3.3.7 Cursor placed on target With chart in active page, and cursor placed on a target symbol, press [ENT] to call up an info window with the following to choose from - text in red are inactive functions: Target found Name: TARGET 1 LAT 57°02.825N...

  • Page 36: Goto Function

    Chapter 3-14 CE33 Chart menu and INFO windows 3.3.8 GOTO function Shortcut to navigation modes: GOTO Select NAV mode To select “Cursor” navigation will require that Chart 1 or Chart 2 is selected and the Cursor cursor is active. Waypoint “Waypoint”, “Route”...

  • Page 37: Plot Function

    CE33 Chart menu and INFO windows Chapter 3-15 3.3.9 PLOT function The CE33 is designed to make navigation easy and safe. Waypoints can be inserted as numbers via the keypad. However, making routes, drawing lines and plotting waypoints etc. are all done directly on the chart.
  • Page 38 Chapter 3-16 CE33 Chart menu and INFO windows figures, change the symbol (cf.section 2.5). From active chart display with cursor on: Plot and save cursor’s position as a waypoint; insert a location name (cf.section 2.6), adjust the position by keying in new figures, change the symbol (cf.section 2.5).

  • Page 39: Chart Setup

    CE33 Chart menu and INFO windows Chapter 3-17 3.4 Chart setup Hotkey to chart CHART With chart active, press [ENT], [9] to load the chart setup for the selected chart (1 or 2) The settings are dedicated to the chart in the active page and does not affect the second chart.
  • Page 40 Chapter 3-18 CE33 Chart menu and INFO windows Paper chart settings Display example contin- ued from previous page. Names Compass distance Chart settings Chart NORMAL Landfilling Boundary lines Mixing levels Marine presentation INTERNATIONAL Simplified draw mode Quick chart info Chart area SMALL Orientation NORTH UP...
  • Page 41 CE33 Chart menu and INFO windows Chapter 3-19 All C-MAP feature groups i.e. Land settings, Marine settings, Naval aids set- tings and Paper chart settings are described in Appendix C. To obtain a ‘cleaner’ view of the chart details, you can turn some of the set- tings OFF if they do not contribute to the clarity of the chart area you wish to explore.
  • Page 42 Chapter 3-20 CE33 Chart menu and INFO windows Chart area can be set to SMALL, MEDIUM or LARGE: SMALL - (default) will open a small chart area big enough to just fill the size of the screen. When panning and scrolling, the chart will automatically be redrawn.
  • Page 43 CE33 Chart menu and INFO windows Chapter 3-21 sailing ‘out of the chart’. Extended level range - (default=ON) will enable changing range 3-4 steps within the same chart level after having selected the range via a numeric key. The remainder of the objects from ‘Non active waypoints’ can all be set to: ON= shown on chart;...
  • Page 44 Chapter 3-22 CE33 Chart menu and INFO windows...

  • Page 45: Position Menu

    CE33 Position menu Chapter 4-1 4. Position menu Position - see section 4.1 Dual speed - see section 4.2 Speed, course & depth - see section 4.3 Speed diagram - see section 4.4 Satellites - see section 4.5 DGPS - see section 4.6 SDGPS - see section 4.7 4.1 Position display...
  • Page 46 Chapter 4-2 CE33 Position menu Status indicator for reception of satellites: a (A)= good, b (B)= acceptable, c (C)= fair, or *= no update - see also “Status indicator and accuracy” below. With built-in or connected DGPS receiver: dGPS= differential data received. DGPS= differential data received and used for corrections.
  • Page 47 CE33 Position menu Chapter 4-3 Position setup From position display, press [ENT] to load Position setup: Datum: 000: World Geodetic System 1984 Reset log: Log 1: 00000.0nm Log 2: 00000.0nm Display position as: LAT/LON Delta position: 0°00.000N 0°00.000E Start position: Lat 57°02N Lon 009°50E Speed and course filter level: Display speed as:...
  • Page 48 Chapter 4-4 CE33 Position menu Reset log - or insert alternative start figure by altering the value in the “Log 1” and/or “Log 2” line. Press [CLR] to reset the figure, and press the numeric keys 0-9 to alter the figure. Display position as - the position can be shown in latitude/ longitude, Loran C or decca coordinates (after selecting chain from the Setup menu).

  • Page 49: Dual Speed Display (Trawling Speed Display)

    CE33 Position menu Chapter 4-5 4.2 Dual speed display (trawling speed display) The analogue differential speed indicator will show how much the present speed varies from the average speed. If the difference exceeds +/- 3 knots (or km/h or miles/h), an arrow will appear which will be pointing out of the scale.

  • Page 50: Speed, Course & Depth

    Chapter 4-6 CE33 Position menu 4.3 Speed, course & depth MENU Call up the menu bar, and... load Speed, course & depth display Speed over ground 18.0kn Course Depth below keel 12.4m This display is preset to show: Speed over ground in knots. Magnetic course.

  • Page 51: Speed Diagram

    CE33 Position menu Chapter 4-7 4.4 Speed diagram MENU Call up the menu bar, and... load “Speed diagram” S= Speed over ground. V= Velocity towards waypoint. W*= Speed through water. SD (Set and drift)*= Speed and direction, true or relative. WIND*= Speed and direction.
  • Page 52 Chapter 4-8 CE33 Position menu The scale for the speed diagram can be adjusted in this display. Time interval can be set in 8 intervals from 1 minute to 3 hours and freeze. Go to the function you wish to change Key in new figure or change setting Confirm entry and return to Speed diagram...

  • Page 53: Satellite Status

    CE33 Position menu Chapter 4-9 4.5 Satellite status MENU Call up the menu bar, and... load satellite status display The display will show which satellites are currently being used for computation of data. It will show their position together with SNR - Signal to Noise Ratio.
  • Page 54 Chapter 4-10 CE33 Position menu The minus key will exclude the satellite, and... the plus key will reinstate it Confirm entry HDOP, PDOP and DOP limits: MENU Call up the menu bar, and... load satellite status display The value of HDOP (horizontal dilution of precision) expresses “the quality”...

  • Page 55: Dgps Information

    CE33 Position menu Chapter 4-11 4.6 DGPS information The DGPS - differential position corrections - can be provided from a built-in module, which is preset to full automatic operation, or from connected DGPS receiver - see “Status indicator” in position display.
  • Page 56 Chapter 4-12 CE33 Position menu Status - can either be: LOCKED = locked on a beacon and receiving differential data. NOT LOCKED = not locked on a becon and receiving no differen- tial data. NOT INSTALLED = there is no built-in DGPS module in unit. NOT IN USE = external DGPS receiver applied.

  • Page 57: Sdgps Information

    CE33 Position menu Chapter 4-13 4.7 SDGPS information The SDGPS - satellite differential GPS - is preset to full automatic operation, which means that the system will utilize the position cor- rections from either differential GPS stations (refer to section 4.6) or satellite differential GPS signals from WAAS, EGNOS or MSAS (refer to section 4.7.1).
  • Page 58 Chapter 4-14 CE33 Position menu Uses corrections from - indicates which differential corrections (DGPS or SDGPS) are currently used for position determination. CHANNEL 1: sat.no. - indicates which satellite number and name is currently tracked/searched by channel 1, and what is the tracking state.

  • Page 59: Satellites In Sdgps System

    It is, however, not expected to become fully employed till sometime in 2003. In the meantime, the system will have limited usage but will be available to all users with the latest Simrad equipment, such as the CE33 ChartSounder. Number...
  • Page 60 Chapter 4-16 CE33 Position menu...

  • Page 61: Waypoints Stored In The Memory

    CE33 Waypoint / route menu Chapter 5-1 5. Waypoint / route menu WP/RTE WP list - see section 5.1 Routes - see section 5.2 Route calculation - see section 5.3 Lines - see section 5.4 Start track - see section 5.5 Stop track - see section 5.5 Tracks...

  • Page 62: Delete Waypoints Via Menu

    Chapter 5-2 CE33 Waypoint / route menu Insert name of waypoint you wish to edit, or... Leaf through waypoints with +/- keys or up/down cursor Open for editing Place the cursor on the function you wish to change Key in new figures, or... toggle between available values PLOT Move the position to ship’s position...

  • Page 63: Routes Stored In The Memory

    CE33 Waypoint / route menu Chapter 5-3 5.2 Routes stored in the memory The route list will keep a record of all the saved routes in the system. It will provide information on number of waypoints in the route etc. Existing routes can be altered via the route list - see further on in this chapter, or directly on the chart via info windows - refer to sec- tions 3.3.4 and 3.3.5.
  • Page 64 Chapter 5-4 CE33 Waypoint / route menu This display provides information on course line, XTE line, route legs, routepoints etc. Call up the Edit route display - if you wish to make any changes. Routepoints Routepoints Setting the Course line to OFF in this display will make the route invisible on the screen.
  • Page 65 CE33 Waypoint / route menu Chapter 5-5 If the XTE distance is not the same in all legs, the value will be *.* instead of the 00.10nm. Navigation mode can be either RHUMB- LINE or GREAT CIRCLE, or... if not set to the same in all legs in a route, the mode will be: COMPOSITE.

  • Page 66: Delete Route Via Menu

    Chapter 5-6 CE33 Waypoint / route menu 5.2.1 Delete route via menu MENU Call up the menu bar, and... load route list Select the route you wish to delete Call up the route details on highlighted route Open for editing Delete route GOTO Confirm that you want to delete the selected route, if not sure: press...
  • Page 67 CE33 Waypoint / route menu Chapter 5-7 the +/- keys and then press [CLR] to remove the point from the route. Display example: Save the route with [ENT] and go to the Edit display - or leave the function with [MENU] to abandon the route. In the Edit route display you can set up the route preferences you need and also change the name of the route.

  • Page 68: Route Calculation

    Chapter 5-8 CE33 Waypoint / route menu 5.3 Route calculation To stay well informed during navigation, the Route calculation display will provide information on how long it takes to go from one point to another, total distance, arrival time etc. MENU Call up the menu bar, and...

  • Page 69: Lines Stored In The Memory

    CE33 Waypoint / route menu Chapter 5-9 5.4 Lines stored in the memory The line list will keep a record of all the saved lines in the system. It will provide information on number of line sections in line etc. ‘Lines’...

  • Page 70: Delete Lines Via Menu

    Chapter 5-10 CE33 Waypoint / route menu Turning “Line” OFF will make the line drawing invisible on the screen. Put it back on the screen by turning it ON again. Place the cursor on the function you wish to change i.e. name, line type or color Toggle between available values Confirm entry...

  • Page 71: Start / Stop Track

    CE33 Waypoint / route menu Chapter 5-11 5.5 Start / stop track The track function will provide a track trailing the movement of your ship. As default from the factory, the first track is stored as TRACK 1, the next as TRACK 2 etc. To start track function: MENU Call up the menu bar, and...

  • Page 72: Tracks Stored In The Memory

    Chapter 5-12 CE33 Waypoint / route menu Type of track line i.e. full, dotted, etc. has 9 different types to choose from in 15 different colors. To stop track: MENU Call up the menu bar, and... load Stop track pop-up window Stop the highlighted track 5.6 Tracks stored in the memory All tracks (of more than 1 trackpoint) will automatically be stored...

  • Page 73: Delete Tracks Via Menu

    CE33 Waypoint / route menu Chapter 5-13 Open for change “Display track” can be set ON/OFF, where OFF will make it invis- ible on the screen. Turn ON to put it back on the screen. Toggle between available values Confirm changes 5.6.1 Delete tracks via menu MENU Call up the menu bar, and...

  • Page 74: Targets Stored In The Memory

    Chapter 5-14 CE33 Waypoint / route menu 5.7 Targets stored in the memory The CE33 can display the bearing and distance of up to three targets at a time in relation to the vessel e.g. harbors or important naviga- tional points. A target is a fixed point on the chart which can be plot- ted by the cursor or from the ship’s position - refer to section 3.3.9, or keyed in via the keypad - refer to section 3.3.7.

  • Page 75: Delete Target Via Menu

    CE33 Waypoint / route menu Chapter 5-15 Toggle between available values Confirm entry 5.7.1 Delete target via menu MENU Call up the menu bar, and... load target display Select the target you wish to delete Open for editing GOTO Delete target Confirm that you want to delete the selected target, if not sure: press [MENU] to exit the display without having made any changes.
  • Page 76 Chapter 5-16 CE33 Waypoint / route menu...

  • Page 77: Pilot Menu - With Nav Inactive

    CE33 Pilot menu & navigation examples Chapter 6-1 6. Pilot menu - with NAV inactive PILOT Highway - see section 6.1 Waypoint navigation - see section 6.5.2 Route navigation - see section 6.5.3 Track navigation - see section 6.5.4 Anchor guard - see section 6.3 Trim &...
  • Page 78 Chapter 6-2 CE33 Pilot menu & navigation examples Navigation setup: Anchor alarm distance: 00.50nm WP circle alarm: 00.10nm WP and cursor navigation: XTE alarm: 00.10nm Navigation mode: RHUMBLINE Route navigation: XTE alarm: Auto waypoint shift: WP-circle Track navigation: XTE alarm: 00.10nm Auto trackpoint shift: WP-circle...

  • Page 79: Pilot Menu - With Nav Active

    CE33 Pilot menu & navigation examples Chapter 6-3 Navigation mode - RHUMBLINE navigation is used for shorter distances, and GREAT CIRCLE for long trips, especially when crossing at high latitudes. COMPOSITE navigation is used when all the legs in a route are not set to the same navigation mode. Auto waypoint shift - can be set to WP-circle, WP-line or OFF.

  • Page 80: Highway Display

    Chapter 6-4 CE33 Pilot menu & navigation examples 6.2.1 Highway display MENU Call up the menu bar, and... load Highway display With navigation mode active, the highway display will provide a graphical steering display: Intended track between two waypoints. XTE alarm lines - refer to sec.6.1 for alarm setup.

  • Page 81: Navigation Setup

    CE33 Pilot menu & navigation examples Chapter 6-5 6.2.2 Navigation setup If you wish to make any changes in the navigation setup, you can quickly enter the navigation setup display by pressing [ENT] from the highway display (graphical steering display). Quick access to navigation setup from active highway display, or...
  • Page 82 Chapter 6-6 CE33 Pilot menu & navigation examples ETA - Estimated Time of Arrival - refers to the inserted local time, and can be calculated to any point used for navigation. AVN - Approximate Velocity Necessary - is automatically calculated in knots after you key in the planned arrival time and date.

  • Page 83: Pilot Mode - Trim & Highway

    CE33 Pilot menu & navigation examples Chapter 6-7 6.2.7 Pilot mode - Trim & highway display Some of the readings rely on data from external log and compass. The Trim & highway display will provide information on actual and mean speed, velocity and water speed - see also section 6.2..8 Set & drift display.

  • Page 84: Pilot Mode - Set & Drift

    Chapter 6-8 CE33 Pilot menu & navigation examples 6.2.8 Pilot mode - Set & drift The readings rely on data from external log and compass. MENU Call up the menu bar, and... load the Set & drift display Relative direction. True direction.

  • Page 85: Anchor Guard

    CE33 Pilot menu & navigation examples Chapter 6-9 6.3 Anchor guard MENU Call up the menu bar, and... activate the anchor guard function -the chart display will provide an impression of the vessel’s position in relation to the alarm circle. To check/change the preset alarm distance: MENU Call up the menu bar, and...

  • Page 86: Navigation Examples

    Chapter 6-10 CE33 Pilot menu & navigation examples 6.5 Navigation examples 6.5.1 Chart/cursor navigation. 6.5.2 Waypoint navigation. 6.5.3 Route navigation. 6.5.4 Track navigation. Relevant for all navigation modes are: - the highway display with graphical steering - section 6.2.1. - the ETA & AVN display with Estimated Time of Arrival and Approximate Velocity Necessary to reach a given point at a specific time - section 6.2.6.

  • Page 87: Waypoint Navigation

    CE33 Pilot menu & navigation examples Chapter 6-11 A course line will now be drawn from actual position (ship’s posi- tion) to destination point (cursor’s position). Next destination: While on the way, you can easily move the cursor to the next destination, and when ready to change navigation leg... GOTO Press [GOTO] and [2] to...
  • Page 88 Chapter 6-12 CE33 Pilot menu & navigation examples From the menu: MENU Call up the menu bar, and... select Waypoint navigation This will activate the pop-up window “Navigate to WP” from where you can choose which waypoint you wish to sail to: Use the cursor to scroll up/down in the waypoint list, or place cursor on the WP number, and...

  • Page 89: Route Navigation

    CE33 Pilot menu & navigation examples Chapter 6-13 6.5.3 Route navigation To start Route navigation will require that at least one route is stored in the memory. Refer to section 3.3.9 PLOT function. When navigating in a route, you will have a graphical steering dis- play to navigate by, see section 6.2.1.
  • Page 90 Chapter 6-14 CE33 Pilot menu & navigation examples Start navigation A course line will now be drawn from ship’s position to the first routepoint. Pressing [GOTO] from chart display during navigation will activate GOTO an INFO window with the following functions to choose from: 1.

  • Page 91: Track Navigation

    CE33 Pilot menu & navigation examples Chapter 6-15 6.5.4 Track navigation A track is created by a series of trackpoints connected by track lines. Using a track for navigation is somewhat like navigating in a route with many waypoints. To start Track navigation will require that at least one track is stored in the memory.
  • Page 92 Chapter 6-16 CE33 Pilot menu & navigation examples Use the cursor to move around in the window if anything needs to be changed - such as Direction in track, etc. Key in the number of the first trackpoint you wish to sail to Start navigation A course line will now be drawn from ship’s position to the first point of destination.

  • Page 93: Echosounder Operation

    CE33 Echosounder operation Chapter 7-1 7. Echosounder operation The echosounder function of the CE33 determines the distance between its transducer and underwater objects such as fish, lake bottom or sea bed. It does this by utilizing the fact that an ultrasonic wave transmitted through water travels at a nearly constant speed of 4800 feet (1500 meters) per second.

  • Page 94: Echosounder Menu

    Chapter 7-2 CE33 Echosounder operation 7.1 Echosounder menu ECHO Echo 50kHz - see section 7.2 Echo 200kHz - see section 7.2 Turn bottom expansion ON - see section 7.3 Turn VRM expansion ON - see section 7.4 Turn A-scope ON - see section 7.5 Depth &...
  • Page 95 CE33 Echosounder operation Chapter 7-3 This is the basic presentation mode (standard display) for observing fish schools and sea bed. Some surface noise may appear just below the transmission line. Transmission line Depth range is adjustable with +/- keys or the Quick- range keys 1-9.

  • Page 96: Bottom Expansion

    Chapter 7-4 CE33 Echosounder operation 7.3 Bottom expansion The advanced bottom lock and expansion feature ensures a reli- able depth readout and provides a compressed standard display in the upper half of the display. The bottom area can be magnified for better separation of echoes.

  • Page 97: Vrm Expansion

    CE33 Echosounder operation Chapter 7-5 7.4 VRM expansion This feature will provide an expanded view of the area near the Variable Range Marker which will give a better separation of echoes. The actual size of the expansion window can be adjusted in the Setup display for 50kHz/200kHz.

  • Page 98: A-Scope

    Chapter 7-6 CE33 Echosounder operation 7.5 A-scope The amplitude scope, which appears in the right side of the echo display, can be turned on and off. The readout indicates the precise amplitude or strength of the last received ping (sounding), which often can be used for determining individual species of fish or hardness or the bottom.

  • Page 99: Variable Range Marker

    CE33 Echosounder operation Chapter 7-7 7.6 Variable range marker From active echo display: Activate the Variable Range Marker function, and... Move the VRM up/down Adjust the range by means of the +/- keys Turn VRM off again 7.7 Depth & temperature diagram MENU Call up the menu bar, and...
  • Page 100 Chapter 7-8 CE33 Echosounder operation Setup for Depth: Scale for depth: 0 -> Color for depth: Scale for temperature: 0 -> 20 °C Color for temperature: Interval of screen: TIME Time interval: 5 MIN. Go to the function you wish to change Key in new figures, or...

  • Page 101: Echosounder Setup

    CE33 Echosounder operation Chapter 7-9 7.8 Echosounder setup The Echosounder setup display mainly consist of general settings, but also applies to a specific frequency where stated. The CE33 fea- tures semi dual transceiver transmitting at 50 and 200 kHz. MENU Call up the menu bar, and...
  • Page 102 Chapter 7-10 CE33 Echosounder operation transfer of data to connected navigator, plotter, etc. Alarm for fish - set the strength from min. 00 (weak echo) to max. 99dB (strong echo), and you can set it ON or OFF. Depth DS fish - define a specific area below the water surface of minimum and maximum depth for the fish alarm.

  • Page 103: Presentation Setup

    CE33 Echosounder operation Chapter 7-11 7.9 Presentation setup The most common settings for adjusting the presentation of the high or low frequency echo picture are accessed by a single keystroke. Press [ENT] from active echo display Setup 200kHz: Range start: 000 m Range: AUTO...

  • Page 104: How The Echosounder Works

    Chapter 7-12 CE33 Echosounder operation 7.10 How the echosounder works When the CE33 is turned on, the processor begins to send electrical pulses to the transducer. The ceramic resonators in the transducer has a special property which enables it to change dimensions slightly when a varying voltage is applied.

  • Page 105: Transducer Beamwidth

    CE33 Echosounder operation Chapter 7-13 7.11 Transducer beamwidth The transducer mounted to the hull of your vessel serves as both a ‘speaker’ when transmitting, and as a ‘microphone’ when the echosounder is receiving. Similar to the way a flashlight focuses light, most of the sound from your transducer is focused downwards with a smaller amount going out to the sides.

  • Page 106: Effects Of The Vessel's Speed

    Chapter 7-14 CE33 Echosounder operation 7.12 Effects of the vessel’s speed The presentation of fish on the CE33 depends directly on the vessel’s speed, as well as on the depth of the fish. When the vessel is at rest, the echo traces will appear stretched and flattened. As the vessel’s speed becomes greater, the echo traces will become shorter and more arched.

  • Page 107: Miscellaneous Menu

    CE33 Miscellaneous menu Chapter 8-1 8. Miscellaneous menu MISC Wind - see section 8.1 MOB position - see section 8.2 DSC alarm - see section 8.3 Data transfer - see section 8.4 8.1 Wind display The CE33 is ready to present wind data from connected instruments. Wind data - the ‘wind instrument’...
  • Page 108 Chapter 8-2 CE33 Miscellaneous menu Load Setup for Wind display Setup for Wind: Damping level: MEDIUM Relative wind scale: NORMAL Wind angle offset: 000° Show wind speed as: RELATIVE Wind speed unit: METERS/SECOND Go to the function you wish to change Toggle between settings, or...

  • Page 109: Mob Position

    8.3 DSC alarm (feature prepared for future DSC VHF) To receive a DSC Alarm and Message from VHF will require that the CE33 is connected to a compatible Simrad VHF radiotelephone. The message from the VHF will appear in a pop-up window together with an acoustic alarm.

  • Page 110: Data Transfer Via Datacard

    Data transfer to and from external memory can be performed via Simrad DataCard. Use the Simrad DataCard to make backup files of all the user data you have created plus the current setups in the internal memory of the unit. Do it whenever you have added important data, or when you wish to transfer routes and waypoints, etc.
  • Page 111 Press [9] to call up a new INFO window where you can see which data is stored in Databank 1 or 2 on the DataCard. Use the +/- keys to toggle between DATABANK 1 and 2 Load: DATABANK-1 Data generated by: Simrad CE33 Saved: 15-02-2002 19:43:00 Name: Data type...

  • Page 112: Data Transfer Via Pc Interface

    Chapter 8-6 CE33 Miscellaneous menu Press [MENU] to exit and *reboot (only if loading “Setup”) MENU *) When the system makes a ‘reboot’ the screen will turn black for a brief moment, then the system will re-start and automatically return to the active display which was on the screen before you made the transfer.
  • Page 113 CE33 Miscellaneous menu Chapter 8-7 Accept warning and continue NMEA connection Transmit WPs Transmit routes Receive WPs and routes MENU Exit The normal communication via the NMEA port is temporarily abrupted during the time of data transfer. Transmit WPs Press [1] to start transmission of all waypoints stored in the CE33 WP list to PC When the transmission is completed you will receive a new info window informing of how many waypoints were transferred.
  • Page 114 “Saving completed” in the info window. You are now ready to: Exit function and return to normal NMEA communication MENU NB! PC-based planning systems differ in operation and performance beyond the control of Simrad.

  • Page 115: Setup Menu

    CE33 Setup menu Chapter 9-1 9. Setup menu SETUP Speed alarm, units & language - see section 9.1 NMEA interface - see section 9.2 Alarm output - see section 9.3 Decca lanes - see section 9.4 Loran C - see section 9.5 Display color - see section 9.6 Factory settings...
  • Page 116 Chapter 9-2 CE33 Setup menu Toggle between available values Serial number: 0x00ffffff Example of the Speed Interface software version: 0x00000025 alarm, units GPS receiver type: N11999 & language PAGE rotation interval: 05 sec. display, Display text in: English GB page 2. PAGE More (2/2)
  • Page 117 CE33 Setup menu Chapter 9-3 Setup for units Depth altitude in - can be set to meters (m), feet (ft) or fathoms (fm). Distance in - can be calculated in nautical miles (nm), kilometers (km) or statue miles (mi). Speed in - can be shown in knots (kn), kilometers/hour (kh) or miles/hour (mh).

  • Page 118: Interface Setup, Nmea

    Chapter 9-4 CE33 Setup menu 9.2 Interface setup, NMEA The NMEA port can be set to: NMEA0183 EXT. DGPS (external DGPS) NMEA0180 NMEA0182 The next pages indicate the default settings for the interface setups. After the interface setups will follow a description of the input and output sentences available in the setups.

  • Page 119: Default Sentences

    CE33 Setup menu Chapter 9-5 Toggle between values, and between ON and OFF Confirm entry, and accept warning (press [ENT] again), or... exit function without making any changes MENU 9.2.1 Default sentences Interface setup - INPUT - Port NMEA0183: Sentence String Status Wind data:...

  • Page 120: Description Of Sentences

    Chapter 9-6 CE33 Setup menu Interface setup - OUTPUT - Port NMEA0183: Sentence String Status Position data: GPS fixdata: Geographic pos, Lat/Lon: WGS84 Geographic pos, Lat/Lon: Recom. min. GPS data: Track made good & SOG: Time and date: ------------------------------------------------- Navigation data: Autopilot sentence ‘B’: Bearing &...
  • Page 121 CE33 Setup menu Chapter 9-7 VTG Course over ground and ground speed. XTE Cross-Track-Error, measured. ZTG UTC & time to destination waypoint. ZDA Time and date. WPL Waypoint location. RTE Routes, ONC ON Complete route, or... ONW ON Working route. RNN Routes.

  • Page 122: Interface Setup, Alarm Output

    Chapter 9-8 CE33 Setup menu 9.3 Interface setup, alarm output MENU Call up the menu bar, and... load display for Alarm output Interface setup, alarm: Output (pin 1,2): Alarm stand-by level: MENU Exit Accept The stand-by level can either be: LOW = 0 volt or HIGH = 5 volt. Use cursor to move around in display, and...

  • Page 123: Decca Lanes

    CE33 Setup menu Chapter 9-9 9.4 Decca lanes MENU Call up the menu bar, and... load decca chain display Leaf through the available chains - see below. Confirm entry To change the position readouts to decca mode, see section 4.1 under Position setup, where ‘Display position as’...

  • Page 124: Loran C

    Chapter 9-10 CE33 Setup menu 9.5 Loran C MENU Call up the menu bar, and... load Loran C chain display Leaf through the available chains - see listing further ahead in this section. If required, go to the slaves, and... Toggle between available slaves (not all chains have more than one slave) ...and it is possible to alter the figures in the time delay...

  • Page 125: Display Color

    CE33 Setup menu Chapter 9-11 List of Loran C chains: Central Pacific 4990 Commando Lion 5970 Gulf of Alaska 7960 North West Pacific 9970 Southeast U.S. 7980 Norwegian Sea 7970 Great Lakes 8970 Mediterranean Sea 7990 Northeast U.S. 9960 Icelandic 9980 Canadian West Coast 5990...
  • Page 126 Chapter 9-12 CE33 Setup menu Page 1 of 2. Page 2 of 2.

  • Page 127: Factory Settings

    CE33 Setup menu Chapter 9-13 9.7 Factory settings DELETE MEMORY: It will be possible to erase a single category of objects entered into the unit by the user - for example, if moving to a different place in the world you may no longer need the routes etc. you have in the memory.
  • Page 128 Chapter 9-14 CE33 Setup menu instructions in the display. However, any attempt to make any type of change, will first of all generate a WARNING display to inform you that you are about to erase some or all data/settings. If you are absolutely sure, press [ENT] to complete the job If not absolutely sure, press [MENU] to exit function without having MENU made any changes...

  • Page 129: Installation And Service

    CE33 Installation and service Chapter 10-1 10. Installation and service 10.1 Installation notes For a number of reasons, all user-related decisions, setups, etc. should be noted in these two pages as they occur. This information may be helpful if your unit has been updated with new software, reset or in for service.
  • Page 130 Chapter 10-2 CE33 Installation and service Other important settings (continued):...

  • Page 131: Installation Of Ce33 Chartsounder

    CE33 Installation and service Chapter 10-3 10.2 Installation of CE33 ChartSounder The CE33 can be flat or bracket mounted - overhead, bulkhead or console. 37.5 (1.5”) 235 mm (9.3”) 252 mm (10”) 100.5 mm (4”) Bulkhead mounting (approx. 10° tilt, allowing space for 45 mm (1.8”)

  • Page 132: Location For Display Unit

    Chapter 10-4 CE33 Installation and service Removable corner Overhead mounting Flush mounting for flush mounting Refer to included template for instruc- tions on flush mounting. Bracket mounting Secure the bracket with two wood screws or bolts (incl.). 10.3 Location for display unit Determine which place is the most suitable and convenient for navigation and general operation after considering the following conditions: - you can see the ship’s bow when you raise or lower your eyes from the dis-...

  • Page 133: Installation Of Ds33 Dual Station

    CE33 Installation and service Chapter 10-5 10.4 Installation of DS33 Dual Station The DS33 is a remote control unit for the CE33 ChartSounder. Both units are identical in size, so the same installation guides can be applied when perform- ing the installation.

  • Page 134: Installation Of Antenna

    Chapter 10-6 CE33 Installation and service 10.5 Installation of antenna The antenna must be placed in a position where tall constructions, steel wires, masts, etc. do not obstruct the view to the satellites. Do not, however, mount the antenna in the top of a mast or tower, as this may degrade the COG and SOG readings, especially if DGPS is used.

  • Page 135: Electrical Connections

    CE33 Installation and service Chapter 10-7 10.6 Electrical connections Ship’s Ground Antenna ECHO Transducer 1: Speed Log Fuse 4.0A slow 2: Speed Log 5V+ 3: Depth + 1 & 2: Red Supply + 4: Depth Shield 10 - 32 Volts 5: Depth - 6: GND T/S Log NMEA 2000...

  • Page 136: Power Supply Connections

    Chapter 10-8 CE33 Installation and service 10.6.1 Power supply connections The internal voltage regulator will allow the CE33 to operate normally within the power supply voltage range from 10 to 32 V DC. The CE33 is connected to external power (battery) by means of the supplied power/NMEA cable. Cable length is approximately 2 meters.

  • Page 137: Optional Connections

    CE33 Installation and service Chapter 10-9 10.7 Optional connections External alarm and function switch The REMOTE connector (refer to section 10.6) includes connections for the dual station as well as the external alarm and function switch. If connection to external alarm or function switch is required, the remote cable must be cut and rejoined as illustrated below: CE33 DS33...

  • Page 138: Basic Transducer And Cable Information

    Chapter 10-10 CE33 Installation and service Overview of various optional connections: -Dual Station DS33 -Performance Instruments -Color Trackplotter -Differential Beacon Receiver -Water speed and temperature sensor -Autopilot -Radar -Yeoman digitizer -NMEA Buffer RS5345 -PC - WPs & routes up/download -Other equipment via NMEA0183, 0182, 0180 10.8 Basic transducer and cable information The installation should be carefully planned in advance, keeping in mind the...

  • Page 139: Transducers (Optional)

    CE33 Installation and service Chapter 10-11 10.8.1 Transducers (optional) Airmar P319 Thru-hull mount Frequency: 50/200 kHz Beamwidth: 45° / 15° Cable length: 10m (32’) Depth information. Reference no. 179-0401-002 (P319) Housing: Reinforced plastic Recommended for fiberglass and metal hulls. Do not use in wooden hulls! Reference no.
  • Page 140 Chapter 10-12 CE33 Installation and service Airmar SS505 - Optional fairing Ref.no. 179-0401-011 Thru-hul stem mount Accomodates hull thickness: Min. no fairing 6 mm (1/4”), Max. with fairing 83 mm (3 1/4”) Frequency: 50/200 kHz Beamwidth: 45° / 15° Cable length: 10m (32’) Depth information.

  • Page 141: Determining The Position For The Transducer

    CE33 Installation and service Chapter 10-13 Airmar B744V Thru-hull triducer Frequency: 50/200 kHz Beamwidth: 45° / 15° Cable length: 10m (32’) Speed, temperature + depth information. Ref.no. 179-0401-009 (B744V) Housing: Bronze Recommended for fiberglass and wooden hulls. 10.8.2 Determining the position for the transducer The CE33 is a sophisticated piece of electronic equipment, but how well it will perform under actual operating conditions will be largely dependent upon the location of the transducer and how it has been installed.
  • Page 142 Chapter 10-14 CE33 Installation and service this reason, it is desirable for the transducer to be mounted on a fairing block which holds the transducer away from the hull and which directs the flow of aerated water around the sides of the transducer rather than over the face of the transducer.

  • Page 143: Preventive Maintenance

    Spare parts – fuses may be bought from a chandler or a marine supply store. Use only fuses specified for this unit – see 10.12 Specifications. If you require a SIMRAD part, please contact your authorized dealer. 10.11 Troubleshooting For all fault finding, first check that the supply voltage is between 10-32 VDC...

  • Page 144: Specifications

    Chapter 10-16 CE33 Installation and service Symptom Check Remedy No GPS position update Check external position to be OFF, refer to interface display in [MENU],[7],[2] Check antenna and cable Replace antenna or cable Screen update is Check that the stored Turn off ‘Course line’...
  • Page 145 CE33 Installation and service Chapter 10-17 Interfacing: 1 port in/out NMEA 0183/0182/0180 PC up/download WPL and RTE 1 port NMEA 2000 (optional) Alarm - signal output 5 V 50 mA Fuse: 4.0A slow GPS section Receiver type: 14 channel parallel, C/A code, 8 state Kalman filter Accuracy: Position (DGPS): 2-5 m RMS...
  • Page 146 45° and 15° beam. P319: 600W plastic thru-hull transducer, 45° and 15° beam. ST650: Speed and temperature only. Options Simrad DataCards C-MAP NT+ electronic charts 6-channel NMEA Buffer RS5345 PC data cable, 1.5 m (153-6070-006) Antenna cable 15 m RG58 DS33 Dual Station, 5.7”...
  • Page 147 CE33 Glossary of terms Appendix A-1 Almanac – a satellite’s almanac data, is data which determines an approxi- mate lane for satellites in orbit. The almanac data is used by the GPS receiver to find and lock onto the satellite signal. CE33 has a built-in basic almanac. Auto trackpoint shift –...

  • Page 148: Appendix A Glossary Of Terms

    Appendix A-2 CE33 Glossary of terms flow passing the transducer. The correct pulse rate is calculated by: 19000 x indicated speed (e.g. 4kn) = 15.200 pulses/nm actual speed (GPS) (e.g. 5kn) Measurement units – the user may select the displayed units to be one of the following: meters feet...
  • Page 149 CE33 Glossary of terms Appendix A-3 Rhumbline – is the straight line to a waypoint on a chart. Route name – each route can be given a name for easy identification. SDGPS - Satellite Differential Global Positioning System - will provide posi- tion corrections from received satellite signals.
  • Page 150 Appendix A-4 CE33 Glossary of terms targets on the display screen. Depths – DK = Depth below keel, DS = Depth below surface, DT = Depth below transducer. Echogram background color – is the color shown on the CE33 in the event no target is present.
  • Page 151 CE33 Glossary of terms Appendix A-5 SHORT less than 10m deep water MEDIUM between 10 and 50 m deep water LONG more than 50m deep water A long pulse will reach deeper but give less resolution. Range – refers to the distance shown from the top to the bottom of the display screen.
  • Page 152 Appendix A-6 CE33 Glossary of terms tions for most of the losses and absorption that occurs as sound energy passes through sea water. There are three settings to choose from, Normal, Special and OFF. The setting “Normal (20 log R) is for general fish finding at depths down to 50m (150’) and it will also give a uniform bottom echo presentation at shallow, mid and deep water.

  • Page 153: Appendix B List Of Datum

    CE33 List of datum Appendix B-1 Select the appropriate datum by 037 Guam 1963 inserting the number prefix: 038 GUX 1 Astro Press [MENU], [2], [1], [ENT], and 039 Hjorsey 1955 key in the desired number by means 040 Hong Kong 1963 of the numerical keys or the +/- keys, 041 Indian confirm entry by [ENT].
  • Page 154 Appendix B-2 CE33 List of datum 081 Southwest Base 082 Timbalai 1948 083 Tokyo 084 Tristan Astro 1968 085 Viti Levu 1916 086 Wake-Eniwetok 1960 087 Wake Island Astro 1952 088 Zanderij 089 Finnish Datum 090 Swedish Datum 091 World Geodetic System 1984 092 World Geodetic System 1984 093 World Geodetic System 1984 094 World Geodetic System 1984...

  • Page 155: Appendix C C-Map Attributes

    CE33 C-MAP attributes Appendix C-1 The optional detailed C-MAP NT+ cards can provide numerous of functions which are accessible via symbols presented on the electronic chart. Place the cursor on a C-MAP object e.g. a buoy or light to call up a small data window with details on the object.
  • Page 156 Appendix C-2 CE33 C-MAP attributes Even though it says “No Attributes” for an object, you may try to press [ENT] to see if there is additional information available for the object. Use the cursor to move up/down in the list of objects in the left column - details on the object will appear in the right column.
  • Page 157 CE33 C-MAP attributes Appendix C-3 Use the same procedure to locate a Hospital, Coast Guard, Fuel Sta- tion, Public Telephone, Provisions, etc. The facility information will stay on the screen for about 10 seconds. Tide information Press the cursor key to activate the chart cursor Press [ENT] from the chart display to call up the Info window Press [3] to call up the C-MAP symbols with available facilities...
  • Page 158 Appendix C-4 CE33 C-MAP attributes Use the +/- keys to select the location where you want to know the tide height Press [ENT] to go to the tide symbol on the location With the cursor placed on the tide symbol, press [ENT] to call up the INFO window Press [2] to access chart info Press [ENT] to expand the information...
  • Page 159 CE33 C-MAP attributes Appendix C-5 The last two lines in the tide display will inform of Sunrise and Sunset for the present day. Caution - the tide information system is quite accurate. However, the predic- tions are subject to variables, which, like the weather, are beyond the control of man.
  • Page 160 Appendix C-6 CE33 C-MAP attributes MARINE SETTINGS Tides, currents: Underwater objects: Nature of seabed: Tide height (predictions) Rocks Seabed area, rocky area, Current Wreck area coral reef Water turbulence Obstruction Weed / kelp Submarine cable Sand waves Depths: Submarine pipeline Spring in seabed Depth contour Cable area, submarine...
  • Page 161 CE33 C-MAP attributes Appendix C-7 Caution areas: Tracks, routes: Buoys: Fishing facility Deep water route part Cardinal Marine farm/culture Deep water route centrel. Installation Cable, submarine Fairway Isolated danger Cable area Ferry route Lateral Offshore production area Navigation line Safe water Pipeline area Precautionary area Special purpose...
  • Page 162 Appendix C-8 CE33 C-MAP attributes...

  • Page 163: Index

    CE33 ChartSounder Index Agents end of manual C-MAP - continued, Alarms, - feature groups 3-19 - anchor - find nearest port services - circle - insert/remove cartridge - depth 7-9,A-3 - objects organized in categories C-5 - DSC - tide information...
  • Page 164 Index CE33 ChartSounder Echosounder functions - continued, ETA & AVN display 6-5,A-1 - color threshold 7-11,A-3 - data field Factory settings 9-13 - demo mode - master reset 9-14 - depth 7-9,A-3 - power off - reset 9-14 - depth grid...
  • Page 165 CE33 ChartSounder Index Installation - continued, MOB function back of front cover - location for display unit 10-4 - alarm and navigation - notes 10-1 - check last activated MOB 6-9,8-3 - sources of noise 10-14 - turn MOB function off...
  • Page 166 Index CE33 ChartSounder PLOT function - continued, Speed - continued, - make route 3-15 - over ground 4-1,4-6 - plot ship’s position as WP 3-15 - setup - plot target 3-15 - through water - plot waypoint 3-15 Status indicator and accuracy...
  • Page 167 CE33 ChartSounder Index Wind - continued, - wind direction - wind relative to the vessel - wind speed, relative or true XTE - cross-track-error 5-4,5-8,6-4,A-3...

  • Page 168: Declarations Of Conformity

    Declaration of Conformity (As required by Article 6.3 of Directive 1999/5/EC-RTTE Directive) Simrad Støvring AS - declare under our sole responsibility that the following products, intended for navigation and world-wide use aboard non-SOLAS vessels, comply with the relevant essential requirements of Directive 1999/5/EC:...
  • Page 169 Garanti SIMRAD garanterer at alle produkter er fri af fejl i materiale og udførelse, som beskrevet nedenstående: KATEGORI “A”: •Autopiloter •Radar •Instrumenter •Navigatorer •Radiotelefoner •Plottere •Gyro kompasser inkl. sensitive elementer •Sonar-systemer •Ekkolod •Trawl Instrumentation. Disse produkter er fra købsdatoen under garanti i en periode på 24 måneder på dele og 12 måneder på...

Table of Contents

Save PDF