SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating.
PECO elects, without charge if the defect appears within 90 days from the date of installation of such part or before the expiration of the original warranty period, whichever is later.
Replace these parts with the engine pulley assembly P#(A0745), 7/16” lock washer P#(K0140), and 7/16”-20 We are pleased to have you as a PECO customer. Your x 4” HHCS P#(K0359) for the 23HP & 25HP, or engine collection system has been designed to give you a low pulley assembly P#(A0419), 7/16”...
Rotating The Donaldson Air Cleaner Figure 2-1e. LESCO CADET Note: If equipped with a Donaldson air cleaner, unit must be rotated to make clearance for top main frame assembly. To rotate Donaldson air cleaner, loosen bolt on air cleaner bracket, rotate air cleaner forward as needed for clearance as shown in Figure 2-1c.
2-3 Main Frame Assembly Installation 2-5 Belt Installation Loosen the (4) bolts P#(K1191), (2) on each side, that Lift the main frame assembly P#(A0845) into position on secure the gear box assembly to the PTO assembly top of the lower mount plate and PTO mount plate P#(A0623) (Figure 2-5a.
2-6 PTO Handle Assembly Installation 2-8 Exhaust Deflector Installation Mount the PTO handle assembly P#(A0603) to the Fasten the exhaust deflector P#(C0058) to the universal PTO P#(A0623) using (3) 1/4”-20 x 3/4” HHCS underside of the PTO mount plate assembly P#(A0846) P#(K1222) and (3) 1/4”-20 nyloc nuts P#(K1128).
2-10 Aluminum Grass Container 2-11 Dump Mechanism Adjustment Installation The linkage may be adjusted in two places, at the NOTE: It is recommended that (3) people assist in adjusting screw P#(K1435) and the latch assembly mounting the container. items. See page 10 for visual clarification. To change the door closure tightness, screw the adjusting screw With three people available, two can lower the container (Figure 2-11a.) in or out.
2-13 Impeller Blade 2-12 Blower Cone Installation Removal/Replacement Thread (1) 5/16”-18 jam nut P#(K0120) onto each end of To Remove: First remove the center bolt (#1), washer (2) 5/16”-18 x 2-1/2” HHCS P#(K0125). Now partially (#2) and spacer (#3) from the taper-lock bushing (#5). thread the bolts into each of the two tabs located on the See Figure 2-13.
2-14 Boot To Mower Deck Installation 2-15 Length Of Hose Adjustment Remove the grass deflector (Figure 2-14a.) from the The hoses in steps 2-16. and 2-17. must be cut to fit mower deck by lifting the deflector and removing the your machine.
CUB CADET Figure 2-19a. 3/8”-16 U-Bolt Weight 2-18 Lower Hose To Boot Installation Take the unattached end of the lower hose and slide it over the circular end of the boot. Use the lower hose clamp to secure the hose to the boot (Figure 2-16). Tip: Before securing clamp rotate hose counter-clockwise (away from yourself) approximately 1”...
SECTION III 3-3 Disengagement Of The Blower OPERATING INSTRUCTIONS A. To disengage the blower, rotate the engagement 3-1 General Safety handle towards the mower. Only qualified people familiar with this operator’s manual WARNING: The blower will continue to spin. DO NOT and the mower’s operator’s manual should operate this TOUCH the blower, pulleys, or the belt until the tractor is machine.
5-1 Parts And Service Information 1. Clean all debris from machine especially from the container, underneath the belt shields, and safety PECO collection system owners should record the name decals. Replace any missing or illegible decals. and telephone number of their Service Center. Your Service Center will be happy to supply replacement 2.
SAFETY DECALS To promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. Part #: R4027 Part #: R1053...