Monogram ZV48SSJSS Installation Instructions Manual
Professional vent hood
Hide thumbs
Also See for ZV48SSJSS:
- Installation instructions manual (17 pages) ,
- Owner's manual (36 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Monogram ZV48SSJSS
Summary of Contents for Monogram ZV48SSJSS
- Page 1 INSTALLATION INSTRUCTIONS 30”, 36” and 48” Professional Vent Hood MONOGRAM.COM...
-
Page 2: Safety Information
Completion Time — 1 to 3 Hours. covered under the warranty. damage electrical wiring and other hidden utilities. monogram.com or call 1.800.444.1845. • Ducted fans must always be vented to the outdoors. monogram.ca CAUTION or call 1.800.561.3344. -
Page 3: Consignes De Sécurité
• Lorsque vous effectuez des découpes ou que vous percez électrique ou tout autre réseau d’alimentation caché. garantie ne s’applique pas. • L’air des ventilateurs disposant de conduits d’aération doit monogram.com ou appelez le 1.800.444.1845. ATTENTION Il faut prendre soin d’installer un conduit monogram.ca ou appelez le 1.800.561.3344. -
Page 4: Información Sobre Seguridad
Tiempo de instalación — 1 a 3 horas. del instalador. Si se producen fallas en el producto debido mismas. visite monogram.com o llame al 1.800.444.1845. monogram.ca o llame al 1.800.561.3344. de reposición (reemplazo) de aire de acuerdo con los requisitos del código local de construcción. -
Page 5: Design Information
Design Information CONTENTS ......................3 ..9 ..........................4 ..............12 ......................4 Tools and Materials Required Tools and Materials Required ................5 .................. 12 Installation Clearances Installation Clearances ....................6 .................. -
Page 6: Installation Preparation
2 Knobs Heat Lamp (2 with 48" models) 2 Grease Filter Trays 2 Implement Rods, 4 Allen Screws (3 supports with 48" models.) and 4 Stand-offs Monogram Logo Allen Wrench Nameplate For Implement Rods HARDWARE PACKAGE Locate and check contents. Screws shown actual size. -
Page 7: Tools And Materials Required
Installation Preparation TOOLS AND MATERIALS REQUIRED (NOT SUPPLIED) Hammer Duct tape Electric or battery operated Key Hole Saw stripper 10" round metal suit installation. Safety glasses Spirit level blade screwdrivers Strain relief for junction cover. Step ladder Metal Snips Saber saw or Sawsall grounded branch circuit. -
Page 8: Advance Planning
Advance Planning OPTIONAL DUCT COVER INSTALLATION CLEARANCES ACCESSORIES These vent hoods are designed to be installed onto a wall or beneath a soffit or cabinet. Standard decorative duct covers are available in cooking surface. running from the top of the hood to the ceiling. NOTE: Clearances may vary due to type of cooking product and local codes. -
Page 9: Determine Installation Height, Duct Cover Accessories
Advance Planning DETERMINE INSTALLATION HEIGHT, DUCT COVER ACCESSORIES These vent hoods must be installed 30” min. to 36” *Possible Actual Hood installed over any professional style Ceiling Installation 6" Duct 12" Duct Height Height Covers Covers determined by the ceiling height. 7' 11"... -
Page 10: Power Supply
Visit Monogram.com for available • Connect the wiring to the house wiring in accordance makeup air solutions (search on the words “make-up with local codes. -
Page 11: Installation Instructions
Installation Instructions STEP 1 DETERMINE HOOD, DUCTWORK AND WIRING LOCATIONS • Use a level to draw the cooktop centerline location. Draw the line to ceiling height. • Measure desired distance from the bottom of the hood to the cooking surface, 30” min. to 36” max. NOTE: If you are installing the hood with duct covers, be sure to read “Using Duct Cover Accessories”... - Page 12 Installation Instructions STEP 2A INSTALL HOOD ONTO WALL IMPORTANT: Framing must be capable of supporting up to 150 lbs. SKIP THIS STEP IF INSTALLING BENEATH A SOFFIT OR CABINET, GO TO STEP 2B. support until they protrude 1/4” forward. This 1/4” gap will provide clearance to hang the hood.
- Page 13 Installation Instructions STEP 2B Alternate Mounting Method INSTALL HOOD TO SOFFIT OR BENEATH CABINETS IMPORTANT: Soffit framing must be capable of supporting up to 150 lbs. SKIP THIS STEP IF USING WALL MOUNTING Top View METHOD Front of Hood 2" supported by the soffit.
-
Page 14: Step 3 Connect Ductwork
Installation Instructions STEP 3 CONNECT DUCTWORK STEP 5 INSTALL DUCT COVERS NOTE: airflow as illustrated. after film is peeled off. • Secure joints in ductwork with sheetmetal screws. Remove protective film from duct covers. If more than with screws provided. seal. -
Page 15: Step 6 Install Filters
Installation Instructions STEP 7 INSTALL IMPLEMENT STEP 6 INSTALL FILTERS RODS Template for Monogram nameplate Monogram nameplate Screw Stand-offs • Insert the grease filter into the opening and drop into Into Hood the trays. Use Allen Wrench to Secure Rod to Stand-offs •... - Page 16 Notes 31-2000859 Rev. 0...
- Page 17 Notes 31-2000859 Rev. 0...
- Page 18 NOTE: safety glasses or goggles should be worn. ® monogram.com or call 1.800.444.1845 NOTE: and specifications are subject to change without notice. 31-2000859 Rev. 0 10-20 GEA Printed in Italy...
Need help?
Do you have a question about the ZV48SSJSS and is the answer not in the manual?
Questions and answers