Maintenance And Repairs - Stihl TS 700 Instruction Manual

English
22.6 Abrasive wheels
The quoted maximum permissible operating
speed of the abrasive wheel must be greater
than or equal to the maximum spindle speed of
the cut-off machine used.
22.7 Abrasive wheels (TS 700)
Outside diameter:
Max. thickness:
Bore diameter/spindle diameter:
Tightening torque:
Composite resin abrasive wheels
Minimum outside diameter of thrust
1) 2)
washers:
3)
Max. depth of cut:
1)For Japan 118 mm2)For Australia
118 mm3)When using thrust washers with an out‐
side diameter of 118 mm, the maximum cutting
depth is reduced to 116 mm
Diamond abrasive wheels
Minimum outside diameter of thrust
1)
washers:
3)
Max. depth of cut:
1)For Japan 118 mm3)When using thrust wash‐
ers with an outside diameter of 118 mm, the max‐
imum cutting depth is reduced to 116 mm
22.8 Abrasive wheels (TS 800)
Outside diameter:
Max. thickness:
Bore diameter/spindle diameter:
Tightening torque:
Composite resin abrasive wheels
Minimum outside diameter of thrust
1) 2)
washers:
3)
Max. depth of cut:
1)For Japan 140 mm2)For Australia
140 mm3)When using thrust washers with an out‐
side diameter of 140 mm, the maximum cutting
depth is reduced to 130 mm
Diamond abrasive wheels
Minimum outside diameter of thrust
1)
washers:
3)
Max. depth of cut:
1)For Japan 140 mm3)When using thrust wash‐
ers with an outside diameter of 140 mm, the max‐
imum cutting depth is reduced to 130 mm
22.9 Sound and Vibration Levels
For further details on compliance with Vibration
Directive 2002/44/EC see www.stihl.com/vib
22.9.1 Sound pressure level L
19432
TS 700:
TS 800:
36
22.9.2
TS 700:
TS 800:
22.9.3
TS 700:
350 mm
TS 800:
4.5 mm
The K‑factor in accordance with Directive
20 mm
30 Nm 2006/42/EC is 2.0 dB(A) for the sound pressure
level and sound power level; the K‑factor in
accordance with Directive 2006/42/EC is
103 mm
2.0 m/s
125 mm
22.10 REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
For information on compliance with the REACH
103 mm
regulation (EC) No. 1907/2006 see
125 mm www.stihl.com/reach.
22.11 Exhaust Emissions
The CO
procedure is specified at www.stihl.com/co2.
400 mm
The measured CO
4.5 mm
representative engine in accordance with a
20 mm
standardized test procedure under laboratory
30 Nm
conditions and does not represent either an
explicit or implied guarantee of the performance
103 mm
of a specific engine.
145 mm The applicable exhaust emission requirements
are fulfilled by the intended usage and mainte‐
nance described in this instruction manual. The
type approval expires if the engine is modified in
any way.

23 Maintenance and Repairs

103 mm
Users of this machine may only carry out the
145 mm
maintenance and service work described in this
user manual. All other repairs must be carried
out by a servicing dealer.
STIHL recommends that you have servicing and
repair work carried out exclusively by an author‐
ized STIHL servicing dealer. STIHL dealers are
regularly given the opportunity to attend training
courses and are supplied with the necessary
to ISO
peq
technical information.
When repairing the machine, only use replace‐
101 dB(A)
ment parts which have been approved by STIHL
101 dB(A)
for this power tool or are technically identical.
23 Maintenance and Repairs
Sound power level L
Vibration level a
hv,eq
Handle, left:
2
6.6 m/s
2
6.5 m/s
2
for the vibration level.
value measured in the EU type approval
2
value was determined on a
2
to ISO 19432
w
113 dB(A)
114 dB(A)
to ISO 19432
Handle,
right:
2
4.5 m/s
2
3.9 m/s
0458-572-0121-E