Table of Contents
Advertisement
I
, O
NSTALLATION
Versymmetric®
Surface Mounted Lift
2311 South Park Rd Louisville, Kentucky 40219
Email:
sales@challengerlifts.com
Office 800-648-5438 / 502-625-0700 Fax 502-587-1933
IMPORTANT:
& M
PERATION
M
VLE10
ODEL
10,000
. C
LBS
APACITY
2500
.
LBS
PER
Web site:
READ THIS MANUAL COMPLETELY BEFORE
INSTALLING or OPERATING LIFT
AINTENANCE
Two Post
A
RM
www.challengerlifts.com
M
ANUAL
Rev. 03/28/2020
Advertisement
Table of Contents
Related Manuals for Challenger Lifts Versymmetric VLE10
Summary of Contents for Challenger Lifts Versymmetric VLE10
- Page 1 & M NSTALLATION PERATION AINTENANCE ANUAL Versymmetric® Two Post Surface Mounted Lift VLE10 ODEL 10,000 APACITY 2500 2311 South Park Rd Louisville, Kentucky 40219 Email: Web site: sales@challengerlifts.com www.challengerlifts.com Office 800-648-5438 / 502-625-0700 Fax 502-587-1933 IMPORTANT: READ THIS MANUAL COMPLETELY BEFORE INSTALLING or OPERATING LIFT Rev.
-
Page 2: General Specifications
Model VLE10 Installation, Operation and Maintenance ENERAL PECIFICATIONS See Figure 1 VLE10 VLE10 w/ 2 Ft. Ext. Kit Rise Height (Screw Pads Highest Position) 74 3/4" (1899 mm) Overall Height 143 7/8" 167 7/8" (3655 mm) (4264 mm) Overall Width 131 5/8"... -
Page 3: Vertical Clearance
Model VLE10 Installation, Operation and Maintenance EAD ENTIRE MANUAL BEFORE ASSEMBLING ERTICAL LEARANCE INSTALLING OPERATING OR SERVICING THIS Check the height of the area where the lift is to be EQUIPMENT installed. Clearance should be calculated based on ROPER MAINTENANCE AND INSPECTION IS the full raised height of the lift. -
Page 4: Installation
Tape measure, 16ft shorted or damaged goods. Do this for your own b. Chalk line protection. c. 4ft level Challenger Lifts NOTIFY AT ONCE if any hidden d. 10” adjustable wrench loss or damage is discovered after receipt. e. Metric open end wrenches 10mm, 13mm, 14mm,... - Page 5 Model VLE10 Installation, Operation and Maintenance NCHORING 4) The anchor bolts must be installed at least 8” from any crack, edge, or expansion joint. 5) Use a concrete hammer drill with a 3/4-inch carbide bit. Tip diameter should conform to ANSI Standard B94.12-1977 (.775 to .787).
- Page 6 Model VLE10 Installation, Operation and Maintenance 23) Beginning on the idler side, attach the idler hose to the cylinder elbow fitting. Route the idler hose (long) up the backside of the column and thru the plastic guide at the top of the extension.
-
Page 7: Arm Installation
Model VLE10 Installation, Operation and Maintenance ELEASE 28) Install Lock Release Rod, Clevis, and Knob to the Power Column Lock using one M10 Nut. 29) Attach Mechanical Lock Release Cable Assembly to each lock pawl. See Fig 9. Fig. 11 – Arm Install 32) Ensure that the arm restraint gears engage and disengage... - Page 8 Model VLE10 Installation, Operation and Maintenance 49) Energize power unit again for 10 seconds. With OLUMN ECAL LACEMENT a clean rag, wipe down both cylinder rods. (The 43) Clean the surface of the columns before placing cylinders are shipped with a small amount of the decals.
- Page 9 Model VLE10 Installation, Operation and Maintenance Wiring Diagram FOR SINGLE PHASE ORIGINALLY CONNECTED TO A2 (Normally Open) FIELD CONNECTIONS FIELD CONNECTIONS FOR THREE PHASE FACTORY WIRED FOR 208−240V RECONNECTIONS FOR 440−480V Fig. 13 – Electrical Wiring Diagram Page 9 Rev. 03/28/2020 VLE10-IOM-A.
-
Page 10: Operation Procedure
Model VLE10 Installation, Operation and Maintenance Requirements Operation, Inspection PERATION ROCEDURE Maintenance; and in the case of frame engaging lift, ALI/LP-GUIDE, Vehicle Lifting Points/Quick AFETY OTICES AND ECALS Reference Guide for Frame Engaging Lifts; in a This product is furnished with graphic safety conspicuous location in the lift area convenient to warning labels, which are reproduced on page 3 the operator. - Page 11 Model VLE10 Installation, Operation and Maintenance IFTING A EHICLE OWERING EHICLE 1) Ensure that the lifting arms are parked, out to full 1) Ensure that the area under the vehicle is clear of drive thru position. personnel and tools. 2) Center the vehicle between the columns in the 2) Raise the vehicle until both latches are free.
-
Page 12: Maintenance
Check for loose or broken parts. Check hydraulic system for fluid leaks. Check adapters for damage or excessive wear. Replace as required with genuine Challenger Lifts parts. Check lock release activation. When properly adjusted, the idler column lock should rest firmly... - Page 13 Model VLE10 Installation, Operation and Maintenance Parts Breakdown Page 13 Rev. 03/28/2020 VLE10-IOM-A.
- Page 14 Model VLE10 Installation, Operation and Maintenance Page 14 Rev. 03/28/2020 VLE10-IOM-A.
- Page 15 Extension Hose (2Ft.Ext. Height) IMPORTANT Replace all worn, damaged, or broken parts with parts approved by Challenger Lifts, Inc. or with parts meeting Challenger Lifts Inc. specifications. Contact your local Challenger Lifts parts distributor for pricing and availability. Call Challenger Lifts at (502) 625-0700 for the distributor in your area.