Table of Contents
Advertisement
Quick Links
Models 8000 / 8100
/ 8200
T
M
o r q u e
a s T e r
r
l
esidenTial and
iGhT
s
l
Tandard
ifT
W
indload
q
s
G
uick
TarT
uide
PLEASE DO NOT RETURN THIS PRODUCT
TO THE STORE
If you need assistance, please call 1-866-
569-3799 (press Option 1) and follow the
prompts to contact a customer service
representative. They will be happy to handle
any questions that you may have.
©Copyright 2020
Wayne Dalton, a division of Overhead Door Corporation
P
®
l u s
c
oMMercial
T a b l e O f C o n t e n t s
QUICK START GUIDE IMPORTANT NOTICES!
This Quick Start Guide is only meant to be used as an aid and
/ or introduction to garage door installation, and does not replace the
complete Installation Instructions and Owner's manual available on the
web at www.Wayne-Dalton.com. Wayne Dalton highly recommends
that you read and fully understand the Installation Instructions and
Owner's Manual before you attempt this installation.
To avoid possible injury, read and fully understand the enclosed
instructions carefully before installing and operating the garage door. Pay
close attention to all warnings and notes. After installation is complete,
fasten this manual near garage door for easy reference.
The complete Installation Instructions and Owner's Manual are available at no
charge from:
- Your local Wayne Dalton Sales Center, or
- Online at www.Wayne-Dalton.com, or
- By mailing to: Wayne Dalton, a division of Overhead Door Corporation, P.O. Box
67, Mt. Hope, OH., 44660
Part Number
341896
2
2
2
4
5
7
12
12
12
12
12
13
REV14_01/15/2020
Advertisement
Table of Contents
Related Manuals for Wayne-Dalton Torquemaster Plus 8000
Summary of Contents for Wayne-Dalton Torquemaster Plus 8000
-
Page 1: Table Of Contents
If you need assistance, please call 1-866- complete Installation Instructions and Owner’s manual available on the web at www.Wayne-Dalton.com. Wayne Dalton highly recommends 569-3799 (press Option 1) and follow the that you read and fully understand the Installation Instructions and prompts to contact a customer service Owner’s Manual before you attempt this installation. -
Page 2: Pre-Installation
Existing Door & Prepar- ensure door operates freely. ing the Opening. These are available for download at www.Wayne-Dalton.com or at your 15. Test electric opener’s safety features monthly, following opener manufacturer’s instruc- local Wayne Dalton Sales Center. - Page 3 weatherstrip with equally spaced nails. Repeat for other side. This will keep the bottom sec- tion from falling out of the opening during installation. Equally space nails approximately 12” to 18” apart.
-
Page 4: Breakdown Of Parts
BREAKDOWN OF PARTS NOTE: The illustrations shown on this page are general representations of the door parts. Each specific door models may have unique variations. Top of vertical Top of vertical track track B2. (Fully Adjustable 3rd hole Feature) B1. (Quick hole set Install Feature) -
Page 5: Door Installation Instructions
the horizontal track angle towards the curved end of the track until the alignment hole in the DOOR INSTALLATION track and angle are aligned. Repeat for other side. Set tracks aside. INSTRUCTIONS Attaching (WL) Jamb Brackets To Vertical Tracks Before installing your door, be certain that you have read and followed all of the instruc- tions covered in the pre-installation section of this manual. - Page 6 At the top of the bottom section, position the graduated end hinge onto the inner end stile of stile. Secure with (2) 1/4” - 20 x 2-3/4” carriage bolts and 1/4” - 20 hex nuts. the bottom section, so that the lower (#) hinge leaf is over the pre-punched holes in the end IMPORTANT: DO NOT MOUNT THE STEP PLATE HIGHER THAN 6”...
-
Page 7: Counterbalance Installation Instructions
other sections, except top section. graduate end hinges and the bottom corner brackets on the left hand side of door, then repeat same process for the right hand side of door. NOTE: Refer to the Windload Specification Sheet to determine if additional 1/4” - 14 x 7/8” self drilling screws are required to be installed into the graduated end hinges, as shown. - Page 8 NOTE: Working with a partner as needed, lift Flag angle the TorqueMaster spring tube assembly up Cam peak ® Counterbalance lift and rest it on top of the flag angles. straight up cable 1/2 pre-wrap TorqueMaster ® Right hand cable spring tube drum assembly assembly...
- Page 9 Left hand Left hand cable drum cable drum Adjusting Counterbalance Lift Cable Bearing Flag Idler bracket angle Starting on the right side, adjust the cable drum assembly by rotating the drum until the set TorqueMaster screw faces directly away from the header. The position of the cam peak on the TorqueMas- ®...
- Page 10 ratchet wheel or the mark on the winding shaft. After 2 to 3 turns, remove the ratchet wrench Cable Left hand and adjust the counterbalance lift cable on the left side. Ensure counterbalance lift cables are drum drum wrap in the first groove of the cable drums, as shown in Step Adjusting Counterbalance Lift Cable. NOTE: Single spring applications require no spring winding on the left hand side, but lift Last cable tension needs to be adjusted.
- Page 11 NOTE: Door not shown for clarity. 90° Header Perforated angle (3) 5/16” Jamb (3) 5/16” Bolts and Jamb Bolts and nuts (3) 5/16” nuts Perforated angle bolted Nail using (2) 5/16” x 1-5/8” Nail hex head lag screws to ceiling member and parallel to door Weather Weather seal...
-
Page 12: Maintenance
Some discoloration of the finish may occur when a door has been exposed 67, Mt. Hope, OH., 44660, or at www.Wayne-Dalton.com. For additional information on to dirt-laden atmosphere for a period of time. Slight chalking may also occur as a result of garage door/operator maintenance go to www.dasma.com and reference TDS 151, 167... -
Page 13: Warranty
Quality garage doors since 1954 Wayne Dalton 2501 S. State Hwy 121 Bus., Suite 200 Lewisville, TX 75067 For service, call (800) 827-3667 www.Wayne-Dalton.com SAFETY INSTRUCTIONS 1. Operate door ONLY when it is properly __________________________________ adjusted and free of obstructions. - Page 14 Thank you for your purchase. PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE If you need assistance, please call 1-866-569-3799 (press Option 1) and follow the prompts to contact a customer service representative. They will be happy to handle any questions that you may have.