Operation - oventrop 1152661 Manual

The installation location of the room thermostat must
comply with the following conditions:
• The room thermostat must not be exposed to a
direct heat source (e.g. sunlight) or cold source.
• A good air circulation must be guaranteed.
• The room thermostat must be easily accessible.
7

Operation

The display shows the current room temperature
(Room). The current time, the day of the week, the set
operating mode and the setting of the fan are also
displayed.
7.1 Switching the thermostat off/on
The thermostat and display are switched off by
pressing the key
switched on again by pressing the key
once more.
7.2 Normal operating mode
Room = Thermostat in operating mode; the display
indicates "Room" and the current room temperature.
Set = By pressing the keys
indicates "Set" and the set nominal temperature. The
set nominal temperature can be increased or reduced
with the help of the keys
modification is only active until the next programmed
temperature.
The symbol is displayed during active temperature
control and during heating or cooling.
7.3 Operating functions
The operating function can be chosen with the
key "MODE": cooling,
ventilation
The fan speed can be set with the key "FAN":
slow, medium,
Auto automatic (only for heating and cooling)
7.4 Modification of the operating mode
The operating mode can be chosen by pressing the
key (thermostat is switched on):
00 = Constant operation
01 = Programming; the display indicates the symbol
and the key
02 = Timer On/Off; the display indicates the symbol
, as soon as the switching points On/Off have been
set
7.5 Setting of the time and the day of the week
Press the time display. Now set the hours with the
help of the keys and
again to set the minutes. Now press the time display
to set the day of the week. These settings can be
carried out in any operating mode.
7.6 Setting of the timer
Having chosen the operating mode "TIMER ON/OFF",
the timer and
appears.
Press the time display as often as necessary until
and the hour display "--:" flash on the display.
The hours can be set by pressing the keys
When pressing the time display again, the minute
display ":--" flashes. The minutes can now be set with
the help of the keys and
Press the time display again.
display flash on the display. The hours can be set with
the help of the keys and
display again, the minutes can be set with the help of
the keys and . Having defined
are completed.
There are two ways to switch off the operating mode:
. The thermostat is
or once, the display
and . This temperature
heating,
fast
. Press the time display
can be set and the symbol
and .
.
and the hour
. By pressing the time
, settings
- Chose the mode "Constant operation" or "Programming"
- Set to "--:--" in the switching mode
7.7 Setting of the weekly programme
If the operating mode "Programming" has been chosen, and the
symbol and the key
be set. Setting of the nominal temperature for the days of the week
(Mo-Fr) and the weekend (Sa-Su) are autonomous. 4 periods per day
can be set.
Press the key . The display now indicates "Set", the figure "1" and
„Mon Tue Wed Thu Fri". The first period for the days of the week can
now be set. Use the keys
and confirm by pressing the time display. Set the required temperature
using the keys and
Repeat this procedure for the periods 2 – 4 of the days of the week.
Now the settings for the weekend (the display shows "Sat Sun") can be
carried out the same way. Programming can be interrupted at any time
by pressing the key .
Chose the mode "Constant operation" or "TIMER ON/OFF" to switch off
the operating mode.
Example: Room temperature for the days of the week shall be set as
follows:
Temperature sequence:
05:30 – 08:00 h 22°C
08:00 – 14:00 h 18°C
14:00 – 23:00 h 23°C
23:00 – 05:30 h 19°C
7.8 Energy saving mode
The energy saving mode is activated by pressing the key
flashes). During cooling mode, the temperature is automatically set to
26°C and the fan to speed slow (
temperature is automatically reduced to 18°C and the fan to speed
slow ( ). The energy saving mode is switched off by pressing the key
.
7.9 Cleaning mode
All key functions are switched off for 10 seconds by pressing the key
. The display can now be cleaned.
7.10 Basic settings
Attentions!
Basic settings must only be carried out by specialists.
Switch off thermostat by pressing the key
for more than 10 seconds to reach the basic settings. Switch between
the individual parameters with the help of the key
are set with the help of the keys
Parameter
1) 12-/24 hour display
2) Locking of the
1)
keyboard
3) Temperature during
energy saving mode
during heating function
4) Temperature during
energy saving mode
during cooling function
2)
5) Frost protection mode
1)
When the locking of the keyboard has been activated, the keys (key
, too) are automatically locked after 30 seconds. The symbol
displayed. The locking of the keyboard is inactivated by pressing the key
6 seconds.
2)
If the room thermostat is switched off and the room temperature drops below
5°C during frost protection mode, the thermostat is switched on automatically (fan
speed: fast) and "Auto" is displayed. The room temperature is now increased to
7°C. Having reached this value, the thermostat is switched off again
automatically.
Further basic settings
Switch off thermostat by pressing the key
key "FAN" for more than 10 seconds to reach further basic
settings. Switch between the individual parameters with the help
of the key . The parameters are set with the help of the keys
and .
and
appear, the temperature programmes can
and to set the required start-up time
and confirm by pressing the time display.
Required setting:
Number 1: 05:30; 22°C
Number 2: 08:00; 18°C
Number 3: 14:00; 23°C
Number 4: 23:00; 19°C
). During heating mode, the
. The parameters
and .
Setting Basic setting
12: 12 hour display
24
24: 24 hour display
00: inactivated
00 (inactivated)
01: activated
5 °C to 35 °C 18 °C
5 °C to 35 °C 26 °C
00: inactivated
00 (inactivated)
01: activated
(key
. Press key
is
for
. Press
7