Tools And Auxiliaries, Check List; Chassis Mounting And Placing The Decorative Labels - Reely ROAD LEOPARD PRO 36 RTR Operating Instructions Manual

4 P
REPARATION
The Stadium Buggy Chassis „LEOPARD PRO 36" is pre-assembled ready to drive (Ready To Run).
Before the first start, some basic adjustments must be carried out or checked and the necessary accessories and auxiliaries must be prepared.
Go through the various points of the check list one after the other, and your model is then ready to run.
Tuning measures on the chassis and/or the installation of another RC system necessitate various tools. The latter are listed below.
4.2
T
OOLS AND AUXILIARIES
T
OOLS
- Socket wrench 17 mm for the wheel nuts
- Flat spanner 5 mm
to set alignment and inclination
Flat spanner 5.5 mm
-
to change the shock absorbers (to counter-hold)
- Allen key 2.5 mm to change the shock absorbers
- Allen wrench 1.5 mm for the
headless screws at the adjusting rings of the
throttle / brake and steering linkage and the
transverse stabilizer
- Allen key 1.5 mm for the grub screws on the
adjusting rings of the throttle/brake and steering
linkages and the transverse stabilizers (optional)
Crosstip screwdriver (Ph No 1)
-
for all other screws on the chassis,
the casings of the differentials and the RC mounting plate
- Screwdriver for the throttle stop screw and the main
nozzle needle
The instructions specific to position front / back / right / left always refer to the
longitudinal axis of the vehicle in drive direction "forward"!
4.3
C
HASSIS MOUNTING AND PLACING THE DECORATIVE LABELS
The fastening elements for the car body are already pre-assembled in the contents of the delivery of the
„LEOPARD PRO 36". Before installing the car body, the boreholes for the car body supports and antenna passage must be mounted.
Use a special car body drill.
Installing the car body
- Apply colored chalk or slow drying paint on the edges of the car body support and
- Place the car body as exactly as possible on the chassis.
- Remove the car body again and
- Drill holes into the car body at the places marked with paint (chalk) for the mounting parts of the car body.
- Place the car body and fasten the latter with the car body splints
- Determine the position of the antenna tube on the car body and
- Drill here also a hole for the antenna passage.
- Make openings for the starter cord, the tank shutter and the cooling head.
The car body of LEOPARD PRO 36 is already cut and painted!
The decorative patterns are glued on the outside of the car body.
-
- Moisten the car body and the decorative patterns with a light washing-up liquid before placing them.
This gives you some time to reposition the decorative patterns and to flatten air bubbles.
- Fine details such as window frames, door sections or borders can be drawn with conventional decorative strips
or waterproof markers.
Select between two tail spoilers.
The flat tail wing is screwed directly onto the car body.
For the broad tail spoiler, you have to screw a tail spoiler support onto the shock absorber bridge. This spoiler support
protrudes beyond the car body.
- Make a cutout with the same width as the tail spoiler support in the center of the car body.
Adjust the depth of the cutout in such a way that the tail spoiler support fits in straight and that the car body can
be attached effortlessly.
- Fix the car body in place with the splints
- Attach the broad spoiler to the spoiler support and secure it with the splint.
44
,
CHECK LIST FOR PUTTING INTO OPERATION
A
UXILIARIES
-
-
-
residues in the engine, after operation („After Run")
C
What must be done:
-
-
-
-
-
-
NOTE!
Operating Instructions 4WD Stadium Buggy Chassis LEOPARD PRO 36 Item No. 23 49 70
Cable fastener
Air filter oil
Low viscosity machine oil for lubrication and
to protect the combustion chamber against corrosive
HECK LIST FOR PUTTING INTO OPERATION
Check alignment and tooth backlash of drive
Function control of servos
Check the range of the remote control transmitter
Check basic carburettor setting
Fill in fuel
Let engine run
Stadium Buggy
Chassis