Perform Gas Leak Test; Wiring Connections - Maxitrol GV60 Installation And Operating Instructions Manual

INSTALLATION INSTRUCTIONS

PERFORM GAS LEAK TEST

1. Check carefully for gas leaks immediately after the valve
has been installed and the gas turned on. Do this be-
fore attempting to operate the appliance or other gas
burning device.
2. Use an approved QRQFRUURVLYH OHDN GHWHFWLRQ ÀXLG RU RWK-
er approved leak detection method, around the diaphragm
ÀDQJHV SLSH FRQQHFWLRQV VHDO FDS DQG DOO RWKHU MRLQWV
Bubbles indicate a leak.
3. If no leakage is detected, light the main burner.
4. With the main burner in operation, apply an approved leak test
solution to all tubing and pipe connections (including adapt-
ers) and the valve inlet and outlet. Bubbles indicate a leak.
5. If a leak is detected, tighten pipe connections (including
adapters) according to "GAS CONNECTIONS" (page 6).
Absolutely no leakage should occur, otherwise there is a
GDQJHU RI ¿UH RU H[SORVLRQ GHSHQGLQJ XSRQ FRQGLWLRQV
Never use if leakage is detected.

WIRING CONNECTIONS

6HH ¿JXUHV ± SDJHV ±
NOTICE
Wiring of valve and receiver must be completed before start-
ing ignition. Failure to do so could damage the electronics.
&RQQHFW DOO FRPSRQHQWV DFFRUGLQJ WR WKH DSSURSULDWH ZLU-
ing diagram.
:KHQ *9 FRPSRQHQWV DUH LQVWDOOHG PDNH VXUH WKH\ DUH
not exposed to dirt, oil, grease or other chemical agents.
'R NOT permit foreign particles under plastic cover.
3ODFH 212)) VZLWFK LI HTXLSSHG ZKHUH LW LV HDVLO\ DF-
cessible for the user.
Thermocouple Circuit
Total resistance of thermocouple circuit should be minimized
to ensure proper operation.
NOTICE
The use of the Mertik Maxitrol interrupter block is rec-
ommended. Keep connection of interrupter block and
thermocouple clean and dry. Avoid severe bending of the
thermocouple tubing during installation (min. 1" radius;
2.5 cm) as this may cause it to fail.
7LJKWHQ LQWHUUXSWHU EORFN LQWR YDOYH ó WXUQ EH\RQG ¿QJHU
tight (2...3 Nm).
6OLGH FDEOHV LQWR SODVWLF LQVHUW
6OLGH SODVWLF LQVHUW ZLWK FDEOHV LQWR WKH EUDVV LQWHUUXSWHU EORFN
:KLOH NHHSLQJ SUHVVXUH RQ WKH FDEOHV DQG SODVWLF LQVHUW
WLJKWHQ WKH WKHUPRFRXSOH óò WXUQ EH\RQG ¿QJHU WLJKW
(2...3 Nm).
Ignition Cable
NOTICE
Do NOT damage the ignition cable while attaching it to the
ignition electrode. When the cable is in place, avoid contact
with sharp objects or edges. With cables longer than 900 mm,
avoid contact with metal parts, as this could decrease spark.
Receiver
NOTICE
To keep the receiver free from debris, dirt, and humidity,
do NOT remove the receiver from the plastic bag until all
construction is complete.
1. Insert batteries or connect AC mains power. The mod-
ule for circulating fan and light/dimmer includes a mains
adapter. With mains adapter, batteries can be used for
backup (RF only).
 3ODFH 212)) VZLWFK LI HTXLSSHG WR ON position.
3. The receiver has to learn the handset code:
3UHVV DQG KROG WKH UHFHLYHU¶V UHVHW EXWWRQ ¿JXUH 
page 8) until you hear two (2) beeps. After the second,
longer beep, release the reset button. Within the subse-
TXHQW  VHFRQGV SUHVV WKH
KDQGVHW XQWLO \RX KHDU WZR  VKRUW EHHSV FRQ¿UPLQJ WKH
code is set.
NOTE: 7KLV LV D RQH WLPH VHWWLQJ RQO\ DQG LW LV QRW UHTXLUHG
when changing the batteries in the handset or re-
ceiver.
4. Check the reception. For better reception straighten the
antenna VHH ¿JXUH  SDJH 
that allows for better reception (see notice below).
5. When the RF-receiver is placed in the appliance, the sur-
rounding metal can reduce reception considerably. The
SRVLWLRQ RI WKH DQWHQQD RQ WKH UHFHLYHU DOVR LQÀXHQFHV
reception.
NOTICE
The antenna must not cross or come into contact with
the ignition wire. This will render the receiver inoperable.
IR Versions
Place the infrared eye in a suitable position. The infrared
VLJQDO WUDQVPLVVLRQ UHTXLUHV D OLQH RI VLJKW
V Module
$Q /(' LQGLFDWHV WKDW SRZHU LV 21
8VH 3RZHU FRUG )DQ DQG /LJKW ZLWK 0ROH[ FRQQHFWHU DF-
FRUGLQJ WR ZLULQJ GLDJUDP ¿JXUH  SDJH RU FRQQHFW
wires with core cable ends to the pluggable screw terminals.
9 0RGXOH ZLWK VFUHZ WHUPLQDOV PD[ $:*  PP
ure 11, page 9).
&RQQHFW WKH /LJKW DQG WKH )DQ ¿UVW DQG WKHQ WKH SRZHU
supply.
7DNH FDUH WKDW XQXVHG RXWOHWV DUH SURWHFWHG IURP FRQWDFW
ELECTRIC SHOCK HAZARD
5HDG WKHVH LQVWUXFWLRQV FDUHIXOO\ )DLOXUH WR IROORZ WKHP
could result in property damage, personal injury, or loss
of life.
7KLV FRQWURO PXVW EH HOHFWULFDOO\ ZLUHG DQG RSHUDWHG LQ
accordance with all codes and local regulations. Service
and installation must be performed by a trained, experi-
enced service technician.
'R NOT use the module if you suspect it may be damaged.
7 / 84
FOR OEM USE ONLY
VPDOO ÀDPH EXWWRQ RQ WKH
and move it to a position
2
¿J-