Table of Contents
Advertisement
MENU
Pump Menu: Settings
SETTINGS
Pump Address
The default pump address is #1.
Note: Sparus
Pumps with Constant Flow Technology
™
Temperature Unit
cannot be connected in series with other pumps.
1. Be sure the green power LED is on and the pump
Screen Contrast
is stopped.
2. Press Menu.
3. Press Select for "Settings". Press Select again to
select "Pump Address".
4. To change the pump address, press Select.
5. Press Up or Down arrows to change the address
number from 1-16.
6. Press Enter to save. To cancel any changes, press
Escape to exit without saving.
7. Press Escape to exit.
Set Time
The time controls all scheduled times, functions, and
programmed cycles and stores the correct time for up
to 96 hours after power is turned off. Reset if the power
is off longer than 96 hours.
1. Check that the green power LED is on.
2. Press Menu.
3. Press Select to select "Settings".
4. Use the Up or Down arrows to scroll to "Set Time"
and press Select.
5. Press Select again and use Up or Down arrows to
set the time.
Note: To change AM/PM, increase or decrease
numbers until the desired time is displayed.
6. Press Enter to save. To cancel any changes, press
Escape to exit without saving.
7. Press Escape to exit.
Set Date
1. Press Menu.
2. Press Select to select "Settings".
3. Use the Up or Down arrows to scroll to "Set Date"
and press Select.
4. Use arrow buttons to set date.
5. Press Enter to save. To cancel any changes, press
Escape to exit without saving.
6. Press Escape to exit.
(1-16) Default: ADDRESS 1
Pump Address
Set Time
(hr:mm) Default: 12:00 AM
AM/PM
Set AM/PM
24 hr.
Fahrenheit - Default: F°
C° Celsius
(1-5) Default 3
English - Default: English
Language
Set Min Speed
(450 RPM - 1700 RPM) - Default: 450 RPM
(1900 RPM - 3450 RPM) - Default: 3450 RPM
Set Max Speed
PASSWORD
Disabled/Enabled - Default: Disabled
Password Time Out (1 min. - 6 hours) Default:10 minutes
Enter Password (xxxx) Default: 1234
Set AM/PM or 24 Clock
Change the time from 12 hour (AM/PM) to 24 hour clock:
1. Press Menu.
2. Press Select to select "Settings".
3. Use the Up or Down arrows to scroll to "AM/PM."
4. Press Select to change the setting.
5. Press Up or Down arrows to choose between 24 hr.
and AM/PM.
6. Press Enter to save. To cancel any changes, press
Escape to exit without saving.
7. Press Escape to exit.
Set Temperature Unit
The default setting is Fahrenheit (°F). The pump can be
set to either Celsius (°C) or Fahrenheit (°F).
1. Press Menu.
2. Press Select to select "Settings".
3. Use the Up or Down arrows to scroll to "Temperature
Units" menu item. Press Select.
4. Use Up or Down arrows to choose Celsius (°C) or
Fahrenheit (°F).
5. Press Enter to save. To cancel any changes, press
Escape to exit without saving.
6. Press Escape to exit.
Set Flow Unit
To change the flow unit to either Gallons per Minute
(GPM) or Litres per Minute (LPM).
1. Press Menu.
2. Press Select to select "Settings".
3. Use the Up or Down arrows to scroll to "Set Flow
Unit". Press Select.
4. Use Up or Down arrows to choose GPM or LPM.
5. Press Enter to save. To cancel any changes, press
Escape to exit without saving.
Set Screen Contrast
Screen contrast levels can be adjusted from 1 to 5
units for low or high lighting conditions.
1. Press Menu.
2. Press Select to select "Settings".
3. Use the Up or Down arrow to scroll to "Contrast
Level".
4. Press Select. Screen will show current contrast
setting number.
5. Press Select to change the setting and use Up or
Down to change number.
6. Press Enter to save. To cancel any changes, press
Escape to exit without saving.
7. Press the Escape button to exit.
SPARUS
Pump with Constant Flow Technology Installation and User's Guide
™
9
Advertisement
Table of Contents
