Pump Settings; Pump Address; Set Time & Set Am/Pm Or 24 Clock; Set Temperature Unit - Pentair Sta-rite INTELLIPRO Installation And User Manual

8
MENU
Pump Menu: Settings
SETTINGS

Pump Address

The default pump address is #1 and only needs to be
changed when there is more than one pump on an
Temperature Unit
automation system. Change the address to allow the
automation system to send a command to the correct
pump.
Screen Contrast
Use this setting if your pump is connected via the RS-485
COM port to an IntelliTouch
Control Systems or IntelliComm
For EasyTouch, SunTouch or IntelliComm systems, the
pump only communicates with address #1. The pump
address can be set from 1-16. The IntelliTouch system
can communicate only to four (1-4) pumps.
Note: IntelliPro
Variable Speed Pumps cannot be
®
connected in series with other pumps.
1. Be sure the green power LED is on and the pump
is stopped.
2. Press Menu.
3. Press Select for "Settings". Press Select again to
select "Pump Address".
4. To change the pump address, press Select.
5. Press Up or Down arrows to change the address
number from 1-16.
6. Press Enter to save. To cancel any changes, press
Escape to exit without saving.
7. Press Escape to exit.
Set Time
The time controls all scheduled times, functions, and
programmed cycles and stores the correct time for up
to 96 hours after power is turned off. Reset if the power
is off longer than 96 hours.
1. Check that the green power LED is on.
2. Press Menu.
3. Press Select to select "Settings".
4. Use the Up or Down arrows to scroll to "Set Time"
and press Select.
5. Press Select again and use Up or Down arrows to
set the time.
Note: To change AM/PM, increase or decrease
numbers until the desired time is displayed.
6. Press Enter to save. To cancel any changes, press
Escape to exit without saving.
7. Press Escape to exit.
INTELLIPRO Variable Speed Pump Installation and User's Guide
®
(1-16) Default: ADDRESS 1
Pump Address
Set Time
(hr:mm) Default: 12:00 AM
AM/PM
Set AM/PM
24 hr.
Fahrenheit - Default: F°
C° Celsius
(1-5) Default 3
English - Default: English
Language
, EasyTouch , SunTouch
® ®
Communication Center.
®
Set Min Speed
(450 RPM - 1700 RPM) - Default: 450 RPM
Set Max Speed (1900 RPM - 3450 RPM) - Default: 3450 RPM
PASSWORD Disabled/Enabled - Default: Disabled
Password Time Out (1 min. - 6 hours) Default:10 minutes
Enter Password (xxxx) Default: 1234
Set AM/PM or 24 Clock
To change the time from a 12 hour clock (AM/PM) to a
24 hour clock:
1. Press Menu.
2. Press Select to select "Settings".
3. Use the Up or Down arrows to scroll to "AM/PM."
4. Press Select to change the setting.
5. Press Up or Down arrows to choose between 24
hr. and AM/PM.
®
6. Press Enter to save. To cancel any changes, press
Escape to exit without saving.
7. Press Escape to exit.

Set Temperature Unit

The default setting is Fahrenheit (°F). The pump can be
set to either Celsius (°C) or Fahrenheit (°F). The Anti
Freeze protection feature (see page 16) can be set to
either Fahrenheit or Celsius.
1. Check that the green power LED is on.
2. Press Menu.
3. Press Select to select "Settings".
4. Use the Up or Down arrows to scroll to "Temperature
Units" menu item. Press Select.
5. Use Up or Down arrows to choose Celsius (°C) or
Fahrenheit (°F).
6. Press Enter to save. To cancel any changes, press
Escape to exit without saving.
7. Press Escape to exit.
Set Screen Contrast
The default setting for the LCD screen is 3. Screen
contrast levels can be adjusted from 1 to 5 units for low
or high lighting conditions.
1. Check that the green power LED is on.
2. Press Menu.
3. Press Select to select "Settings".
4. Use the Up or Down arrow to scroll to "Contrast
Level".
5. Press Select. Screen will show current contrast
setting number.
6. Press Select to change the setting and use Up or
Down to change number.
7. Press Enter to save. To cancel any changes, press
Escape to exit without saving.
8. Press the Escape button to exit.