Small Chassis - Calrec M3 Operator's Manual

M3
............................................................................................................................... . ...................................................
SMALL CHASSIS OUTPUT GUIDE
Connector
Type
PIN No.
1 . 18
34 . 2
35 . 19
3 . 36
20 . 4
37 . 21
5 . 22
38 . 6
39 . 23
7 . 24
40 . 8
41 . 25
9 . 26
42 . 10
43 . 27
11 . 28
44 . 12
45 . 29
13 . 46
30 . 14
47 . 31
15 . 48
32 . 16
49 . 33
17 . 50
*
INS / DIR 1-4 also applies to circuits in connectors INS/DIR 5-8 respectively (INS/DIR 5-8 may also
contain group circuits in slots 7-8)
nc = not connected, if for example the mono PQ5122 or mono XL5125 is fitted
All Enable & Logic 7lines are active low and are pulled down to 0L when activated or to activate.
All cable screens should be connected to chassis.
CR (Centre Rail) is a clean audio earth reference & is provided for earth reference for unbalanced circuits only
and should not be used as a general cable screen.
All VCA lines should be terminated to CR when not used.
0L (0 Volts logic earth for DC switching)
L .R are the Left & Right signals of a stereo output.
M is the mono output.
38
INS / DIR 1-4 * INS / DIR 9-10 MN INS 1&2
50F D-TYPE 50F D-TYPE
(Free Male Plug) (Free Male Plug)
CIRCUIT CIRCUIT
Ch 1 Insert Go L Ch 9 or Gp 3 Insert Go
or M L or M
Ch 1 Insert Go R Ch 9 or Gp 3 Insert Go
or nc R or nc
Ch 1 Insert Return Ch 9 or Gp 3 Insert Return
L or M L or M
Ch 1 Insert Return Ch 9 or Gp 3 Insert Return
R or nc R or nc
Ch 1 Direct Output Ch 9 or Gp 3 Direct Output
L or M L or M
Ch 1 Direct Output Ch 9 or Gp 3 Direct Output
R or nc R or nc
Ch 2 Insert Go Ch 10 or Gp 4 Insert Go
L or M L or M
Ch 2 Insert Go Ch 10 or Gp 4 Insert Go
R or nc R or nc
Ch 2 Insert Return Ch 10 or Gp 4 Insert Return
L or M L or M
Ch 2 Insert Return Ch 10 or Gp 4 Insert Return
R or nc R or nc
Ch 2 Direct Output Ch 10 or Gp 4 Direct Output
L or M L or M
Ch 2 Direct Output Ch 10 or Gp 4 Direct Output
R or nc R or nc
Ch 3 Insert Go L
or M Main 1 Insert Go L
Ch 3 Insert Go
R or nc Main 1 Insert Go R
Ch 3 Insert Return
L or M Main 1 Insert Ret L
Ch 3 Insert Return
R or nc Main 1 Insert Ret R
Ch 3 Direct Output
L or M
Ch 3 Direct Output
R or nc
Ch 4 Insert Go
L or M Main 2 Insert Go L
Ch 4 Insert Go
R or nc Main 2 Insert Go R
Ch 4 Insert Return
L or M Main 2 Insert Ret L
Ch 4 Insert Return
R or nc Main 2 Insert Ret R
Ch 4 Direct Output
L or M Studio LS EXT CUT / 0L
Ch 4 Direct Output
R or nc Monitor LS EXT CUT / 0L
Chassis Chassis
ANCILLARY 1 PRINCIPLE O/P'S
50F D-TYPE 50F D-TYPE
(Free Male Plug) (Free Male Plug)
CIRCUIT CIRCUIT
Main 1 DESK Output L
Ch 1/2 Remote Cut 7
Main 1 DESK Output
R
Ch 3/4 Remote Cut 7
Main 1 LINE Output L Talkback O/P
Ch 5/6 Remote Cut 7
Ch 7/8 or Gp 1/2
Main 1 LINE Output R
Remote Cut 7
Ch 9/10 or Gp 3/4
Remote Cut 7 Main 1 LINE Output M
CR / CR Main 2 DESK Output L
Main 2 DESK Output
Ch 1/2 VCA Control 7 R
Ch 3/4 VCA Control 7 Main 2 LINE Output L
Ch 5/6 VCA Control 7 Main 2 LINE Output R
Ch 7/8 or Gp 1/2 VCA
Main 2 LINE Output M RTB I/P
Control 7
Ch 9/10 or Gp 3/4 VCA
Control 7
CR / CR
Monitor LS Output L
Ch 1/2 Fader Start 7
Monitor LS Output R
Ch 3/4 Fader Start 7
Headphone Output L
Ch 5/6 Fader Start 7
Ch 7/8 or Gp 1/2 Fader
Start 7 Headphone Output R
Ch 9/10 or Gp 3/4
Fader Start 7 PFL LS Output
CR / CR Aux 1 Output M
ON-AIR relay com/no Aux 2 Output M
Tx 'E' / 0L Aux 3 Output M
Tone 7 / TB 7 Aux 4 Output L
AFL / PFL Aux 4 Output R
Studio LS Output L
SLS Bus 7 / -
External Tone Output Studio LS Output R
Chassis Chassis
MONITOR
50F D-TYPE
(Free Male Plug)
CIRCUIT
Monitor Bargraph
O/P L
Monitor Bargraph
O/P R
SLS External I/P
1L
SLS External I/P
1R
SLS External I/P
2L
SLS External I/P
2R
Monitor LS SEL
O/P L
Monitor LS SEL
O/P R
RTB Enable 7 / 0L
Mix Minus External
I/P
Mix Minus External
O/P
CR / CR
External Talkback
O/P 1
External Talkback
O/P 2
Monitor LS I/P A1L
Monitor LS I/P A1R
Monitor LS I/P A2L
Monitor LS I/P A2R
Monitor LS I/P A3L
Monitor LS I/P A3R
Monitor LS I/P A4L
Monitor LS I/P A4R
Chassis