Subscribe to Our Youtube Channel
Related Manuals for Huck ALCOA 2620
Summary of Contents for Huck ALCOA 2620
- Page 1 NSTRUCTION ANUAL 2620 A2620 2620-PT A2620-PT YDRAULIC NSTALLATION OOLS ® ® ® Makers of Huck , Marson , Recoil Brand Fasteners, Tools & Accessories December 3, 2015 HK1012...
-
Page 2: Ec Declara On Of Conformity
2620 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK1012... -
Page 3: Table Of Contents
2620 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK1012 ONTENTS EC Declara on of Conformity ..... . 2 Safety Instruc ons . -
Page 4: Safety Instruc Ons
Huck representative. movement. 11. Only genuine Huck parts shall be used for replacements or If the assembly power tool is fi xed to a suspension device, spares. Use of any other parts can result in tooling damage make sure that fi... - Page 5 2620 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK1012 AFETY NSTRUCTIONS (continued) IV. REPETITIVE MOTION HAZARDS: Wear warm clothing when working in cold conditions and 1. When using assembly power tool, the operator can keep hands warm and dry. experience discomfort in the hands, arms, shoulders, neck If numbness, tingling, pain or whitening of the skin in the or other parts of the body.
-
Page 6: Specifi Ca Ons
DEXRON is a registered trademark of General Motors Corp. MERCON is a registered trademark of Ford Motor Corp. HOSE KITS: Use only genuine HUCK Hose Kits rated Quintolubric is a registered trademark of Quaker Chemical Corp. @ 10,000 psi (689.5 bar) working pressure. - Page 7 2620 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK1012 PECIFICATIONS CONTINUED 10.1 NCHES (25.8) (cm) (15.9) (9.7) Ø 10° (7.2) (3.4) Ø (5.4) (4.1) (17.8) ODELS 2620-PT & A2620-PT...
-
Page 8: Principle Of Opera On
2620 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK1012 RINCIPLE OF PERATION IGURE IGURE Piston Travel Piston Travel PULL PISTON PINTAIL EJECTOR DUMP VALVE TRIGGER SWITCH HYDRAULIC HOSES Pressurized Oil RETURN PRESSURE RETURN PRESSURE PULL PRESSURE PULL PRESSURE Return Oil PULL PRESSURE RETURN PRESSURE... -
Page 9: Prepara On For Use
2620 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK1012 REPARATION FOR WARNING: Huck recommends that a Huck WARNINGS: POWERIG ® be used to power Huck tools. - Read entire manual before using tool. (Only use the POWERIG as indicated in - A 30-minute training session with its instruction manual.) Hydraulic power... -
Page 10: Opera Ng Instruc Ons
2620 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK1012 PERATING NSTRUCTIONS TO INSTALL A HUCKBOLT® FASTENER: WARNINGS: - Wear approved eye and hearing CAUTION: Remove the excess gap from protection. between the sheets to ensure that enough - Ensure adequate clearance for operator’s of the pintail emerges from the collar hands before installing fasteners. - Page 11 NOTE: Where a part number (P/N) is given, Huck PREVENTIVE MAINTENANCE sells that part. Huck recommends that you: - Inspect the tool and nose daily for damage and wear.
-
Page 12: Maintenance
SUPER-O-LUBE is a registered trademark of Parker Hannifi n Corp. LUBRIPLATE is a registered trademark of Fiske Brothers Refi ning jaws soak; dry them immediately after cleaning. Huck recommends drying other parts before re-assembling. Tefl on is a registered trademark of E. I. du Pont de Nemours and For additional information, see the appropriate Nose Company. -
Page 13: Disassembly
2620 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK1012 ISASSEMBLY This procedure is for complete disassembly of the 8. Standard Models: Remove the O-ring and Back-up tool. Disassemble only those components necessary ring. (Figures 8 & 10) to replace damaged rings and worn or damaged Model 2620-PT: Remove the O-ring, Back-up ring, components. -
Page 14: Assembly
2620 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK1012 SSEMBLY This section details the re-assembly of the tool. For 3. Thread the Piston Assembly Tool (P/N 123111-6) component identifi cation, see Figures 2, 4–13, and onto the piston. (Figure 5) NOTE: Do NOT install Spacer 123112-6. - Page 15 2620 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK1012 SSEMBLY CONTINUED 9. Remove the Piston Assembly Tool and the GLYD Ring Insertion Tool from the back of the cylinder. (Figure 6) 10. From the rear of the cylinder, install the dump valve with four fl...
-
Page 16: Assembly Drawings Standard Models
2620 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK1012 SSEMBLY RAWINGS TANDARD ODELS IGURE 16 17 2620 & 2620-15 22 EJECTOR GLAND ASSEMBLY IGURE 16 17 A2620 22 EJECTOR GLAND ASSEMBLY... -
Page 17: Assembly Drawings Pt Models
2620 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK1012 PT M SSEMBLY RAWINGS ODELS IGURE 2620-PT & 2620-PT-15 IGURE A2620-PT... -
Page 18: Parts List
501127 O-ring 507412 507412 507412 507412 Polyseal 507408 507408 507408 507408 Front Gland 125609 125609 125609 125609 HUCK Sticker 590517 590517 590517 590517 GLYD Ring Assembly 122769-1 122769-1 122769-1 122769-1 CE & WARNING Sticker 590512-5 590424-7400 590512-5 590424-7400 End Cap... -
Page 19: Hose Assembly Drawing - Electric Trigger Models
2620 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK1012 SSEMBLY RAWING LECTRIC RIGGER IGURE... -
Page 20: Hose Assembly Drawing - Air Trigger Models
2620 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK1012 SSEMBLY RAWING RIGGER IGURE... -
Page 21: Troubleshoo Ng
2620 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK1012 ROUBLESHOOTING Always check the simplest possible cause (such as a loose or disconnected trigger line) of a malfunction fi rst. Then proceed logically, eliminating other possible causes until the cause is discovered. Where possible, substitute known good parts for suspected defective parts. -
Page 22: Kits & Accessories
& CCESSORIES Huck has created product-specifi c Spare Parts Service Kits that contain various perishable parts. The types and quantities of spare parts that should be available vary with the application and tools in use. Have the appropriate kit accessible when using this tool and when performing maintenance on it. - Page 23 fi xtures that are not in good action is necessary. condition or repair and suitable for their intended Huck shall not be liable for any loss or damage purpose. resulting from delays or non-fulfi llment of orders owing THERE ARE NO WARRANTIES WHICH to strikes, fi...
- Page 24 The Future of Tooling Technology, and Tools express, implied, or statutory; all warran es of Produc vity are service marks of Huck are contained only in Huck’s wri en quota ons, Interna onal. Huck provides technical assistance acknowledgments, and/or purchase orders. It For the Long Haul ™...
Need help?
Do you have a question about the ALCOA 2620 and is the answer not in the manual?
Questions and answers