Huck BTT35LS Instruction Manual

Bobtail hydraulic tool

Advertisement

Quick Links

I
M
NSTRUCTION
ANUAL
B
I
S
OBTAIL
NSTALLATION
YSTEM
BTT35LS
BTT35LS
04-06-2010
HK1107

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BTT35LS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Huck BTT35LS

  • Page 1 NSTRUCTION ANUAL OBTAIL NSTALLATION YSTEM BTT35LS BTT35LS 04-06-2010 HK1107...
  • Page 2 BTT35LS BOBTAIL Installation Tool Alcoa Fastening Systems...
  • Page 3: Table Of Contents

    BTT35LS BOBTAIL Installation Tool Alcoa Fastening Systems ONTENTS ONTENTS ...........4 AFETY .
  • Page 4: Afety

    19. Unsuitable postures may not allow counteracting of Huck equipment. normal expected movement of tool. 3. Huck equipment must be maintained in a safe 20. Do not abuse tool by dropping or using it as a ham- working condition at all times. Tools and hoses mer.
  • Page 5: Principle Of Operation

    PULL and RETURN, and are not equipped with relief valves are The tool is intended for use with Huck standard indus- specifically not recommended, and may be trial POWERIG® Hydraulic Units (models 913H, 918, dangerous.
  • Page 6: Pecifications

    PECIFICATIONS PECIFICATIONS Power Source: Huck POWERIG Hydraulic Unit Tool PULL Capacity: 35,000 lbs Hose Kits: Use only genuine HUCK Hose Kits rated PULL Pressure: 8000 psi MAX @ 10,000 psi working pressure. RETURN Pressure: 6500 psi MAX Hydraulic Fluid: ATF meeting DEXRON III, DEXRON IV, MERCON, Allison C-4 or equivalent specifications.
  • Page 7: Use

    Observe action of tool. Check for fluid leaks. 2. Use only a HUCK Powerig that is recommended or equivalent that has been prepared for opera- 5. Attach the proper Nose Assembly to the tool.
  • Page 8: Perating

    BTT35LS BOBTAIL Installation Tool Alcoa Fastening Systems PERATING NSTRUCTIONS PERATING NSTRUCTIONS 1. Push the tool’s nose over the end of the fastener until it WARNING: To avoid pinch point, never place hand bottoms out. between nose assembly and work piece.
  • Page 9: Maintenance

    (Slic-Tite * is Clean nose assembly often. Dip in mineral spirits or available in stick form as Huck P/N 503237.) similar solvent to clean puller and wash away metal • Smear LUBRIPLATE ® 13OAA*, or equivalent lubri- chips and debris.
  • Page 10: Arts Ist

    BTT35LS BOBTAIL Installation Tool Alcoa Fastening Systems SSEMBLY ARTS SSEMBLY ARTS (Figures 5 and 6) ITEM DESCRIPTION BTT35LS QTY. Piston Assembly 128955 Piston Rod Pipe Plug 503703 O-Ring 506089 Back-up Ring 501151 Forward Gland Assembly 121890 Forward Gland Wiper 506065...
  • Page 11: Rawing

    BTT35LS BOBTAIL Installation Tool Alcoa Fastening Systems Figure 5...
  • Page 12: Quipment

    BTT35LS BOBTAIL Installation Tool Alcoa Fastening Systems ROUBLESHOOTING ROUBLESHOOTING Always check the simplest possible cause of a mal- 6. Tool operates erratically and fails to install fastener function first. For example, a loose or disconnected properly. trigger line. Then proceed logically and eliminate each a.
  • Page 13 Huck shall not be liable for any loss or damage result- THERE ARE NO WARRANTIES WHICH EXTEND ing from delays or nonfulfillment of orders owing to...
  • Page 14 Huck’s written quotations, acknowledge- International. Huck provides technical assistance ments, and/or purchase orders. It is recommend- regarding the use and application of Huck fasten- ed that the user secure specific, up-to-date data ers and tooling. and information regarding each application and/or use of such products.

Table of Contents