Related Manuals for Huck 7352
Summary of Contents for Huck 7352
- Page 1 Instruction Manual 7352 Hydraulic Regional Jet Clearance Tool (shown with nose assembly attached) December 7, 2018 HK1042...
- Page 2 7352 Hydraulic Regional Jet Clearance Tool (HK1042)
-
Page 3: Table Of Contents
7352 Hydraulic Regional Jet Clearance Tool (HK1042) Contents Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5 Specifications . -
Page 4: Safety Instructions
3. Be aware that failure of the workpiece, accessories, equipment. or the inserted tool itself can generate high velocity 2. Huck equipment must be maintained in a safe working projectiles. condition at all times . Tools and hoses should be 4. -
Page 5: Safety Instructions
7352 Hydraulic Regional Jet Clearance Tool (HK1042) Safety Instructions (continued) IV. rePeTITIVe MOTION HAzArDS: VIII. VIbrATION HAzArDS: 1. When using assembly power tool, the operator can 1. Exposure to vibration can cause disabling damage to experience discomfort in the hands, arms, shoulders, the nerves and blood supply to the hands and arms. -
Page 6: Specifications
7352 Hydraulic Regional Jet Clearance Tool (HK1042) Specifications POWer SOUrCe: Huck POWERIG Hydraulic Unit HOSe KITS: Use only genuine HUCK Hose Kits rated @ 10,000 psi (689.5 bar) working pressure. MAX OPerATING TeMP: 125° F (51.7° C) HyDrAULIC FLUID: Hydraulic fluid shall meet MAX FLOW rATe: 2 gpm (7.5 l/m) -
Page 7: Principle Of Operation
7352 Hydraulic Regional Jet Clearance Tool (HK1042) Principle of Operation PULL STrOKe When the trigger is pressed, hydraulic pressure is Figure 1 directed to the PULL side of the piston, and the piston and nose assembly collet move rearward, installing the fastener . -
Page 8: Preparation For Use
7352 Hydraulic Regional Jet Clearance Tool (HK1042) Preparation for Use press the trigger a few times to cycle the tool and to WArNING: Correct PULL and reTUrN circulate the hydraulic fluid. Observe the action of the pressures are required for operator’s safety tool and check for leaks. -
Page 9: Maintenance
. See Kits & Accessories . before performing maintenance, disconnect - Follow the disassembly and assembly procedures in the tool’s electric control trigger from this manual. If Huck recommended procedures are not the POWerIG Hydraulic Unit before ®... -
Page 10: Hydraulic Couplings
7352 Hydraulic Regional Jet Clearance Tool (HK1042) Maintenance (continued) PreVeNTIVe MAINTeNANCe POWerIG MAINTeNANCe Maintenance instructions and repair procedures are in System Inspection the appropriate POWERIG Instruction Manual. Operating efficiency of the tool is directly related to the performance of the complete system, including the tool... -
Page 11: Disassembly
7352 Hydraulic Regional Jet Clearance Tool (HK1042) Disassembly This procedure is for complete disassembly of the sliding back the plastic shrouds. tool . Disassemble only those components necessary NOTe: Use the following steps only if the switch, to replace damaged rings and worn or damaged wire, or connector is in need of repair. -
Page 12: Assembly Drawing
7352 Hydraulic Regional Jet Clearance Tool (HK1042) Assembly Drawing Figure 3... -
Page 13: Parts List
7352 Hydraulic Regional Jet Clearance Tool (HK1042) Parts List ITeM PArT NO. DeSCrIPTION QTy. 126939 Head Assembly contains: (not sold separately) Machined Head 500812 (Item 13) O-ring 501106 (Item 12) Back-up Ring 590424-5700 Sticker (pressure warning & CE) 126932 Drawbar... -
Page 14: Troubleshooting
Accessories & Huck has created product-specific Spare Parts Service Kits that contain various perishable parts for each tool. The types and quantities of spare parts that should be available vary with the application and tools in use. Have the appropriate kit accessible when using this tool and when performing maintenance on it . - Page 15 Determination is Outside USA and Canada made on a case-by case basis upon return of parts to Huck Contact your nearest Huck International location (see International, Inc. for evaluation.
- Page 16 Huck provides technical assistance regarding the use and application of © 2018 Huck International, Inc. Huck fasteners and tooling. NOTICE: The ISO 9001-2015 information contained in this publication Arconic Fastening Systems is only for general guidance with regard CERTIFIED to properties of the products shown and/...
Need help?
Do you have a question about the 7352 and is the answer not in the manual?
Questions and answers