Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Huck Alcoa 2600 Series
Summary of Contents for Huck Alcoa 2600 Series
- Page 1 2600 Series 2600 2600-12 2600-16 2600-16-3 2600-16-12 2600-16-2T 2600-16-30T 2600-16-50T ydraulIc nstallatIon ools Makers of Huck , Marson , Recoil ® ® ® Brand Fasteners, Tools & Accessories January 5, 2016 HK914...
-
Page 2: Ec D Eclaration Of C Onformity
2600 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK914... -
Page 3: Table Of Contents
2600 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK914 ontents Ec d . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 EclaratIon of onforMIty . -
Page 4: S Afety I Nstructions
Huck representative. movement. 11. Only genuine Huck parts shall be used for replacements or If the assembly power tool is fixed to a suspension device, spares. Use of any other parts can result in tooling damage make sure that fixation is secure. - Page 5 2600 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK914 afety nstruCtIons (continued) IV. REPETITIVE MOTION HAZARDS: Wear warm clothing when working in cold conditions and 1. When using assembly power tool, the operator can keep hands warm and dry. experience discomfort in the hands, arms, shoulders, neck If numbness, tingling, pain or whitening of the skin in the or other parts of the body.
-
Page 6: S Pecifications
DEXRON is a registered trademark of General Motors Corp. MERCON is a registered trademark of Ford Motor Corp. HOSE KITS: Use only genuine HUCK Hose Kits rated Quintolubric is a registered trademark of Quaker Chemical Corp. @ 10,000 psi (689.5 bar) working pressure . -
Page 7: P Rinciple Of O Peration
2600 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK914 rInCIple of peratIon PULL PRESSURE Piston Travel Piston PULL Cycle When the Trigger Switch is pressed, pressurized hydraulic fluid moves through the PULL hose to the front side of the Piston . The piston and nose assembly collet move rearward, installing the fastener . -
Page 8: Reparation For Se
2600 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK914 reparatIon for WARNINGS: WARNING: Huck recommends that a Huck - Read entire manual before using tool. POWERIG be used to power Huck tools. ® - A 30-minute training session with... -
Page 9: O Perating I Nstructions
2600 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK914 peratIng nstruCtIons TO INSTALL A HUCKBOLT® FASTENER: WARNINGS: - Wear approved eye and hearing CAUTION: Remove the excess gap from protection. between the sheets to ensure that enough - Ensure adequate clearance for of the pintail emerges from the collar operator’s hands before installing... -
Page 10: Aintenance
. prevent nicking/pinching rings on rough/tight spots . NOTE: Where a part number (P/N) is given, Huck PREVENTIVE MAINTENANCE sells that part. Huck recommends that you: SYSTEM INSPECTION - Inspect the tool and nose daily for damage and wear . -
Page 11: Ssembly Of
. Do not let Slic-tite is a registered trademark of LA-CO Industries, Inc. jaws soak; dry them immediately after cleaning . Huck Loctite is a registered trademark of Henkel Corporation, U.S.A. recommends drying other parts before re-assembling . -
Page 12: Isassembly
2600 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK914 IsasseMbly This procedure is for complete disassembly of the 10 . Use a small, dull pointed “pick” to remove all tool . Disassemble only those components necessary seals, wipers, O-rings, and Back-up rings from the to replace damaged rings and worn or damaged components . -
Page 13: Ssembly
2600 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK914 sseMbly This section details the re-assembly of the tool . For 3 . Push the front wiper housing into the front gland . component identification, see Figures 2–6 . Carefully press the Polyseal into the front gland, taking care NOT to pinch the inner ring . - Page 14 2600 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK914 sseMbly ContInued 11 . Lubricate the inside of the assembled rear gland WARNING: Connect the tool’s hydraulic assembly, and press into the cylinder . hoses to the POWERIG before connecting ®...
-
Page 15: A Ssembly D Rawing
2600 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK914 sseMbly rawIng Igure * Control Cord for specific (*see P ARTS part numbers) 118944-* Hose Assembly (*see P for specific ARTS part numbers) -
Page 16: P Arts L Ist
123337-1 120341-3 120341 127760-4 127760-1 127760 Strain Relief 505344 Setscrew 501731 Trigger Switch Assy 120361 Pintail Tube 122771 HUCK Sticker 590517 CE WARNING Sticker 590512-5 Lug Adapter 129995 Cap Screw 506033 Mounting Block 508462 Hose Sleeve (not 120770-7 120770-6 shown) (1) Piston 122759 is not sold separately. -
Page 17: Roubleshooting
2600 Series Hydraulic Installation Tools ( Alcoa Fastening Systems & Rings HK914 roubleshootIng Always check the simplest possible cause (such as a loose or disconnected trigger line) of a malfunction first. Then proceed logically, eliminating other possible causes until the cause is discovered . Where possible, substitute known good parts for suspected defective parts . -
Page 18: Its Ccessories
& CCessorIes Huck has created product-specific Spare Parts Service Kits that contain various perishable parts . The types and quantities of spare parts that should be available vary with the application and tools in use . Have the appropriate kit accessible when using this tool and when performing maintenance on it . - Page 19 . material, tooling and fixtures that are not in good Huck shall not be liable for any loss or damage condition or repair and suitable for their intended resulting from delays or non-fulfillment of orders owing purpose .
- Page 20 The Future of Tooling Technology, and Tools express, implied, or statutory; all warranties of Productivity are service marks of Huck are contained only in Huck’s written quotations, International. Huck provides technical assistance acknowledgments, and/or purchase orders.
Need help?
Do you have a question about the Alcoa 2600 Series and is the answer not in the manual?
Questions and answers