Subscribe to Our Youtube Channel
Related Manuals for Huck 2620
Summary of Contents for Huck 2620
- Page 1 Distributed by Toll Free 1 800 563 1293 NSTRUCTION ANUAL 2620 2620 A2620 A2620 2620-PT 2620-PT A2620-PT A2620-PT YDRAULIC NSTALLATION OOLS 02-27-2012 HK1012...
-
Page 3: Table Of Contents
2620 series Tooling Alcoa Fastening Systems (HK1012) ONTENTS ONTENTS EU D ......2 ECLARATION OF CONFORMITY . -
Page 4: Afety
ANSI Z87.1 - 2003 26. Tool is only to be used as stated in this manual. Any other use 6. Only genuine Huck parts shall be used for replacements or is prohibited. spares. Use of any other parts can result in tooling damage or personal injury. -
Page 5: Rinciple Of Peration
2620 series Tooling Alcoa Fastening Systems (HK1012) RINCIPLE PERATION RINCIPLE PERATION Piston Travel Piston Travel PULL PISTON PINTAIL EJECTOR DUMP VALVE TRIGGER SWITCH HYDRAULIC HOSES Pressurized Oil RETURN PRESSURE RETURN PRESSURE PULL PRESSURE PULL PRESSURE Return Oil Return Pressure (Return Cycle) Pull Pressure (Pull Cycle) Fig. -
Page 6: Specifications
POWER SOURCE: MAX OPERATING TEMP: Huck POWERIG Hydraulic Unit 125°F (51.7°C) HOSE KITS: MAX FLOW RATE: Use only genuine HUCK Hose Kits rated @ 10,000 2 gpm (7.5 l/m) psi working pressure. MAX PULL PRESSURE: HYDRAULIC FLUID: 7400 psi (510 bar) - Page 7 2620 series Tooling Alcoa Fastening Systems (HK1012) PECIFICATIONS CONTINUED PECIFICATIONS CONTINUED 6.562 166.69 5.496 139.61 3.062 2.827 77.77 ø 1.350 71.81 10° 34.30 2.160 ø 54.86 7.046 178.97 1.606 40.81 INCHES Model 2620/A2620 10.162 258.1 6.270 159.27 3.836 97.43 2.827 1.350...
- Page 8 2620 series Tooling Alcoa Fastening Systems (HK1012)
-
Page 9: Operating
Spare Parts Kit part no. 2620KIT or procedures in this manual. SSEMBLY SSEMBLY 2620-PTKIT should be kept on hand. Inspect cylinder bore, ® CAUTION: Do not use TEFLON * tape on piston and piston rod and unloading valve for scored surfaces, pipe threads. -
Page 10: Disassembly
Remove Retaining Ring (17), cover plate (16) and Ejector Gland Assembly (22) with Hex Key 122048 Locking Disk (18). 2620-PT Model: (Fig. 9 & 11) 16. Standard Models Only: (Fig. 4, 8 & 10) Remove Deflector (32), Screws (31), Barbed Retainer Remove from gland, Ejector Rod (29), Washer (23), (30) and locking disk (18). -
Page 11: Assembly
Back-up Ring (8) on End Cap (15). NOTE: Clean components with mineral spirits, or similar 2620-PT Model: (Fig.7, 9 & 11) Install Back-up Ring solvent. Inspect for wear/damage and replace as (8), O-ring (9), Wiper (33), Polyseal (34), Washer (35) necessary. - Page 12 2620 series Tooling Alcoa Fastening Systems (HK1012) 2620 & 2620-15 2620 & 2620-15 SSEMBLY RAWING SSEMBLY RAWING FIG 8 16 17 22 EJECTOR GLAND ASSEMBLY Model 2620 & 2620-15...
- Page 13 2620 series Tooling Alcoa Fastening Systems (HK1012) 2620-PT & 2620-PT-15 2620-PT & 2620-PT-15 SSEMBLY RAWING SSEMBLY RAWING FIG 9 Model 2620-PT & 2620-PT-15...
- Page 14 2620 series Tooling Alcoa Fastening Systems (HK1012) Figure 10 16 17 22 EJECTOR GLAND ASSEMBLY SSEMBLY SSEMBLY A2620 A2620 RAWING RAWING Figure 11 SSEMBLY RAWING SSEMBLY RAWING A2620-PT A2620-PT...
-
Page 15: Parts Lists
TICKER OCATIONS The 2620 series tools come labeled with Sticker part number 590424-7400, which contains safety and pressure settings information. It is necessary that this sticker remain on the tool and is easily read. If sticker becomes damaged or worn, or if it have been removed from the tool, or when replacing Cylinder, this sticker must be ordered and placed in the location shown. - Page 16 2620 series Tooling Alcoa Fastening Systems (HK1012) FIG 12...
-
Page 17: Hose Assembly Drawing - Air Trigger Models
2620 series Tooling Alcoa Fastening Systems (HK1012) FIG 13... -
Page 18: Models
2620 series Tooling Alcoa Fastening Systems (HK1012) ROUBLESHOOTING ROUBLESHOOTING Always check the simplest possible cause of a c. Not enough collar lubricant. malfunction first. For example, a loose or disconnected d. Nose assembly installed NOSE trigger line. Then proceed logically and eliminate each ASSEMBLY DATA SHEET. - Page 19 Service Parts Kits, Service Tools Kits and Nose Assemblies. Please OOLING THER TEMS NOT contact your Huck Representative or the nearest MANUFACTURED BY Huck office listed on the back cover for the ATSC in HUCK MAKES NO WARRANTY WITH RESPECT your area.
- Page 20 251 Cree Crescent, Winnipeg, MB Canada R3J 3X4 Tel : 204 837 8361 1 800 563 1293 • Fax: 204 837 3520 1 800 974 1494 • applifast.com...
Need help?
Do you have a question about the 2620 and is the answer not in the manual?
Questions and answers