Subscribe to Our Youtube Channel
Related Manuals for Huck Arconic 507
Summary of Contents for Huck Arconic 507
- Page 1 NSTRUCTION ANUAL YDRAULIC NSTALLATION 12-27-2013 HK480...
-
Page 2: Ec Declaration Of Conformity
(HK480) Arconic 507 HYDRAULIC INSTALLATION TOOL Test data to support the above information is on file at Huck International, Inc., Kingston, NY, USA. Vibration Measurements are frequency weighted in accordance with ISO 8041 (1990). -
Page 3: Table Of Contents
(HK480) Arconic 507 HYDRAULIC INSTALLATION TOOL EC Declaration of Conformity ..... Safety ......... Description . -
Page 4: Safety
Do not use other types or sizes of accessories or consumables. mended before using Huck equipment. 2. Huck equipment must be maintained in a safe working condition at all times. Tools VI. WORKPLACE HAZARDS: and hoses should be inspected at the beginning of each shift/day for damage or 1. -
Page 5: Description
‐32 (1” diameter) or ‐36 (1‐1/8 diameter) fasteners. proper function of the Tool and Nose Assemblies, and for the safety of the operator. HUCK Gage T‐124833CE is avail‐ Each tool has a cylinder and piston assembly. An relief able for checking these pressures. Instructions are furnished valve, designed to relieve the hydraulic pressure at both with the gage and Powerig®... -
Page 6: Principle Of Operation
Huck Powerig Hydraulic Units be used PULL stroke, it uncovers flats on the rear end of the Relief as a power source for Huck installation Valve. These flats were designed to provide a passage for equipment. Hydraulic power units that... -
Page 7: Preparation For Use
103392, into tool port ‘‘R.’’ Connect Tool’s hydraulic hoses to Powerig Hydraulic Unit before connecting Tool’s 2. Use a Huck Powerig or equivalent that has been switch control cord to unit. If not connect- prepared for operation per applicable instruction ed in this order, severe personal Injury manual. -
Page 8: Operating Instructions
(HK480) Arconic 507 HYDRAULIC INSTALLATION TOOL For safe operation. Please read completely WARNINGS: TO INSTALL A HUCKBOLT FASTENER: To avoid severe personal injury: Wear approved eye and ear protection. Be sure 1. Check work and remove excessive gap. (Gap is the of adequate clearance for Operator’s space between sheets. -
Page 9: Kits And Accessories
(HK480) Arconic 507 HYDRAULIC INSTALLATION TOOL DESCRIPTION USED FOR PART NO. Service Kit Includes Seals, etc for tool service. 507KIT Hex Key, 5/16 across flats Socket Head Screws in Handle 502446 Hex Key 3/32 across flats Set Screw in Trigger Switch 501623 Locking Ring Wrench Locking Ring... -
Page 10: Maintenance
Pipe threads may cause tape to 1. Inspect tool and nose for external damage. shred resulting in tool malfunction. (Slic- Tite is available in stick form as Huck part number 503237.) 2. Verify that hydraulic hose fittings and couplings and electrical connections are secure. -
Page 11: Disassembly And Assembly
Huck as part number 502723). sure. A special Spanner Wrench, Part No. 110362, is avail- able from Huck to aid in the disassembly and assem- (c) Apply a continuous strong pressure, rather than bly of Locking Ring, reference No. 11. Piston Rod sharp blows, to disassemble or assemble a compo- Guide Part No. - Page 12 Pipe threads may cause tape to (d) Replace O-Rings and back-up rings. Be sure that shred resulting in tool malfunction. (Slic- Tite is available in stick form as Huck part relative positions of the O-Rings and back-up rings number 503237.) are as shown in Figures.
-
Page 13: Assembly Drawing With Part Numbers
(HK480) Arconic 507 HYDRAULIC INSTALLATION TOOL... -
Page 14: Troubleshooting
(HK480) Arconic 507 HYDRAULIC INSTALLATION TOOL Always check the simplest possible cause of a malfunction first. For example, a loose or disconnected trigger line. Then proceed logically, eliminating each possible cause until the defective part is located. Where possible, substitute known good parts for suspected defective parts. Use Trouble Shooting Chart as an aid for locating and correcting trouble. - Page 15 Huck shall not be liable for any loss or damage resulting from delays or non-fulfillment of orders owing to strikes, Two Year Limited Warranty on Installation Tools: fires, accidents, transportation companies or for any Huck International, Inc.
- Page 16 For the Long Haul ™...
Need help?
Do you have a question about the Arconic 507 and is the answer not in the manual?
Questions and answers