Philips EM6E Service Manual page 19

Side connections
Camera or Camcorder
&
Connect your camera or camcorder as shown.
é
Connect to
VIDEO
equipment. For stereo equipment also connect
S-VHS quality with an S-VHS camcorder is obtained by
connecting the S-VHS cables with the S-video input
audio inputs 3.
Do not connect cable 1 and 2 at the same time. This may cause
1 2 3
picture distortion !
Headphone
Insert the plug into the headphone socket L as shown.
&
Press ¬ on the remote control to switch off the internal
é
loudspeakers of the TV.
The headphone impedance must be between 8 and 4000 Ohm. The
headphone socket has a 3.5 mm jack.
In the Sound menu select
headphone volume.
Note:
When Dual screen/PIP is activated (see p. 16):
- if the main screen displays a TV channel picture, you hear the sound
from the Dual screen/PIP picture through your headphone.
Wired rear loudspeakers
When no wireless RF surround sound is possible or when there
SURROUND
is too much interference you can still enjoy Dolby Pro Logic II
and Dolby Digital surround sound by connecting the wireless
receiver box to the TV with a stereo cinch to stereo 3.5 mm
13 V DC in 13 V DC in V DC in
jack cable.
AUDIO in AUDIO in AUDIO in &
Connect the (not supplied) cable to the
(TV) (TV) (TV)
4 /15W 4 /15W 4 /15W
connector 4 at the wireless receiver box and the
2.8V RMS 2. 2.8V RMS 8V RMS
R R L L
4 4
1 1 4 4 surround outputs at the back of the TV.
2 2 3 3
é
Select Off in the Wireless surround menu item of the Setup,
1 2 2
3 3 Speakers menu, p. 9.
Connect extra subwoofer
To enhance the sound reproduction of your TV you can connect
an externally powered subwoofer (between 20 and 250 Hz).
SUBW.
&
Connect the audio cable of the external subwoofer to the
SUBW. socket at the back of your TV.
é
Select
External
For details, please refer to the subwoofer's manual.
28
2 and 3 for mono
AUDIO L
3.
AUDIO R
1
and
to adjust the
Headphone volume
AUDIO IN (TV)
R and L
in the Setup, Speakers menu, Subwoofer, p. 9.
Connect audio receiver
Although your TV is already equipped with a Digital MultiChannel decoder you might want to connect
your own MultiChannel surround receiver.
MultiChannel surround receiver with or without digital input connectors
&
Connect a MultiChannel surround receiver to the
R and L connectors at the back of your TV.
AUDIO AUDIO
é
OUT OUT If you want the loudspeakers of your TV to act as centre
speaker, also connect an audiocable to the MultiChannel
surround receiver
CENTRE IN CENTRE IN CENTRE IN
connector at the back of your TV.
CENTRE IN
"
DIGITAL Select Centre input On
AUDIO
OUT loudspeakers of the TV will now only produce centre sound.
'
If necessary, adjust the volume level of the centre sound in the
Centre in volume
volume has to be controlled via the MultiChannel surround
receiver.
(
In case of a Digital MultiChannel surround receiver, also connect
the receiver to the
In this case the loudspeakers of your TV can not act as centre
speaker. Select
see the instructions manual of your Digital MultiChannel surround
receiver.
To select connected equipment
Press the v key on the remote control repeatedly to select
according to where you connected your equipment at the back or the right side of your TV.
Remark : Most equipment (decoder, recorder) carries out the switching itself, when it is switched on.
Cinema Link Surround receiver
See the separate supplied Cinema Link instruction manual
Attention: the sound info on screen will not correspond with the actual sound reproduction.
Recorder or DVD with EasyLink
&
The recorder (VCR or DVD+ RW) or DVD can be
operated with the remote control via the Recorder
é
or DVD menu on screen.
Recorder
"
Ò p ‡ π † ® Ï
Rwd Play Stop Play Ffw Rec Eject
DVD
Ò p ‡ π † Ï
Prev. Play Stop Play Next Eject
AUDIO OUT
connector and to the
CENTRE OUT
in the Source menu; See p. 11.The
menu item of the Source menu.The overall
DIGITAL AUDIO OUT connector.
in the Source menu, see p. 11. Also
Centre input Off
, , , or
EXT1 EXT2 EXT3 EXT4 SIDE
Press the MENU key on the remote control.
Select the Recorder or DVD menu with the
cursor up/down.
Press the cursor left/right, up/down to select
one of the recorder or DVD functions.
The key ® for recording can be operated in the TV
mode.
If your EasyLink recorder has the system standby
function, when you press the B key for 3 seconds,
both TV and the recorder are switched to standby.
29