All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by WS 0764 BG CD Customer Service...
EN 2 LC7.2E PA Technical Specifications, Connections, and Chassis Overview 1. Technical Specifications, Connections, and Chassis Overview Index of this chapter: 1.1.3 Miscellaneous 1.1 Technical Specifications 1.2 Connection Overview Power supply: 1.3 Chassis Overview - Mains voltage (V : 220 - 240...
Page 3
Technical Specifications, Connections, and Chassis Overview LC7.2E PA EN 3 Connection Overview H_16960_006.eps 030407 Figure 1-1 Side and rear I/O connections Note: The following connector colour abbreviations are used - Function Select 0 - 2 V: INT (acc. to DIN/IEC 757): Bk= Black, Bu= Blue, Gn= Green, Gy= 4.5 - 7 V: EXT 16:9...
Page 4
EN 4 LC7.2E PA Technical Specifications, Connections, and Chassis Overview Common Interface - D2- Data channel 68p - See diagram B03C - D1+ Data channel - Shield - D1- Data channel Service Connector (UART) - D0+ Data channel - UART_TX...
Be careful during measurements in the high voltage by the workshop during a repair: section. • Use only lead-free soldering tin Philips SAC305 with order • Never replace modules or other components while the unit code 0622 149 00106. If lead-free solder paste is required, is switched "on".
EN 6 LC7.2E PA Directions for Use avoid mixed regimes. If this cannot be avoided, carefully 2.3.6 Exchanging a Defective PDP clear the solder-joint from old tin and re-solder with new tin. If a PDP has defective or "dead" pixels, do the following: 2.3.5...
Mechanical Instructions LC7.2E PA EN 7 4. Mechanical Instructions Index of this chapter: Notes: 4.1 Cable Dressing • Several models in this chassis range have a different 4.2 Service Positions mechanical construction, the instructions given in this 4.3 Assy/Panel Removal chapter are therefore very model specific.
Page 8
EN 8 LC7.2E PA Mechanical Instructions Service Positions Assy/Panel Removal For easy servicing of this set, there are a few possibilities 4.3.1 Rear Cover created: • The buffers from the packaging. Warning: Disconnect the mains power cord before you remove •...
Page 9
Mechanical Instructions LC7.2E PA EN 9 4.3.3 Keyboard Control Panel [E] 4.3.4 Side I/O Panel [D] 1. Refer to next fig. “Keyboard control panel“. 1. Remove the bottom “speaker cover”, as described earlier. 2. Remove the T10 Parker screws [1] from the shielding.
Page 10
EN 10 LC7.2E PA Mechanical Instructions 4.3.7 Power Supply Board The PSU belongs to the PDP panel. Please refer to the PDP repair manual for more info (info on front page). 4.3.8 Small Signal Board [B] 1. Unplug all connectors. Carefully unplug the LVDS connector as it is very fragile.
Page 11
Mechanical Instructions LC7.2E PA EN 11 4.3.10 Glass Plate 1. Refer to figures “Glass plate“ below. 2. Remove T10 Parker screws [1] along the side of the glass plate, and remove the metal fixation brackets. 3. Lift the glass plate form the set.
“Panel Code (Dec)” in table “Option codes OP1 ...OP7 • Display information (“SDM” or “SAM” indication in upper (for all LC7.2E models)” in chapter 8 “Alignments”, or see right corner of screen, error buffer, software version, sticker on the side/bottom of the cabinet. When the value is operating hours, options and option codes, sub menus).
Page 13
Service Modes, Error Codes, and Fault Finding LC7.2E PA EN 13 In case a call centre or consumer reads “See Type Plate” in CSM mode, he needs to look to the side/bottom sticker to identify the set, for further actions.
Page 14
EN 14 LC7.2E PA Service Modes, Error Codes, and Fault Finding The error buffer will only be cleared when the “clear” command 5.2.3 Service Alignment Mode (SAM) is used in the SAM menu. Purpose Note: • To change option settings.
Page 15
Service Modes, Error Codes, and Fault Finding LC7.2E PA EN 15 uploading via ComPair. Read paragraph “Service Tools” - > “ComPair”. Caution: When this mode is selected without Upon entering the Customer Service Mode, the following ComPair connected, the TV will be blocked. Remove the screen will appear: AC power to reset the TV.
Page 16
EN 16 LC7.2E PA Service Modes, Error Codes, and Fault Finding 5.2.5 Digital Customer Service Mode (DCSM) Purpose The Digital Customer Service Mode shows error codes and information on the IBO Zapper module (DVB reception part) operation settings. The call centre can instruct the customer to activate DCSM by telephone and read off the information displayed.
Page 17
Introduction whether the Small Signal Board (SSB) or the display of a Flat ComPair (Computer Aided Repair) is a Service tool for Philips TV is defective. Thus to determine if LVDS, RGB, and sync Consumer Electronics products. and offers the following: signals are okay.
Page 18
EN 18 LC7.2E PA Service Modes, Error Codes, and Fault Finding Error Codes Table 5-3 Error code overview Error 5.4.1 Introduction code Description Item nr. Remarks No error. Error codes are required to indicate failures in the TV set. In DC Protection of speakers.
Page 19
PC Card Adapters (Sandisk or Kingston) • 12 short blinks followed by a pause of 1.5 seconds, with memory sizes of up to 256MB. Philips does not • 9 short blinks followed by a pause of 1.5 seconds, guarantee that other types of portable memory cards and •...
Page 20
EN 20 LC7.2E PA Service Modes, Error Codes, and Fault Finding Software Upgrade Procedure 1. Power ON your TV with the power switch at the side of the TV. Put your TV ON by using the remote controller if the TV is in Stand-by.
Page 21
Service Modes, Error Codes, and Fault Finding LC7.2E PA EN 21 Fault Finding and Repair Tips Alternative method (1): 1. Go to SAM. 2. Select NVM Editor. Notes: 3. Select ADR (address) to 1 (dec). • It is assumed that the components are mounted correctly 4.
Page 22
EN 22 LC7.2E PA Service Modes, Error Codes, and Fault Finding AC ON Start Up (1) +5VSTBY to be measured +5VSTBY & +3V3STBY Available (1) at PDTC114ET (item 7322) RENEAS POR by +3VSTBY (2) (2) to be measured at pin 4...
Page 23
Service Modes, Error Codes, and Fault Finding LC7.2E PA EN 23 Start SEMISTANDBY/ STANDBY Mute Audio BL_ADJ stop dimming (PWM duty cycle 100%) BL_ON_OFF = LOW Wait 300ms 300ms Switch OFF LVDS 20ms Wait 20ms LCD_PWR_ON = LOW Software Shutdown:...
Page 24
EN 24 LC7.2E PA Service Modes, Error Codes, and Fault Finding Power Down INT: AC OFF or Transient INT Start Avoid false trigger Poll the Power Down INT for 5 times Mute Audio & VIdeo Notes: 1. Power Down INT will be based on fall edge triggering 2.
Block Diagrams, Test Point Overview, and Waveforms LC7.2E PA Block Diagram Video VIDEO B03A TUNER IF & DEMODULATOR +5VS 7113 TDA9886T/V4 1101 TD1316AF/IHP-2 DEMODULATOR 1102 SUPPLY VIF1 VIF1 IF_ATV CVBS MAIN SOUND TRAPS IF_OUT1 VIF-PLL TUNER VIF2 4.5 to 6.5 Mhz...
Block Diagrams, Test Point Overview, and Waveforms LC7.2E PA Block Diagram Control & Clock Signals CONTROL & CLOCK SIGNALS B03B DVB-DEMODULATOR B03C DVB-COMMON INTERFACE B03A TUNER IF & DEMODULATOR B03D DVB-MOJO B04B VIDEO PROCESSOR 1101 7202 7204 TD1316AF/IHP-2 SVP CX32-LF...
Circuit Diagrams and PWB Layouts LC7.2E PA SSB: DVB - Mojo Analog Back End 1001 D7 IJ66 C1 1002 D7 IJ67 D8 DVB-MOJO ANALOG BACK END B03F B03F 1J14 D6 IJ68 D8 2J01 B7 2J02 B7 2J04 B8 2J05 C8...
Alignments LC7.2E PA EN 65 8. Alignments Index of this chapter: 8.3.1 Tuner Adjustment (RF AGC Take Over Point) 8.1 General Alignment Conditions 8.2 Hardware Alignments Purpose: To keep the tuner output signal constant as the input 8.3 Software Alignments signal amplitude varies.
Page 66
LG : 50 HD X4 LC07_EU_DTV_PDP_Pan Europe (/12) SDI : 42 HD W2 867000026881 42PFP5532D/12 LG : 42 HD X4 SDI : 50 HD W2 867000026885 50PFP5532D/12 LG : 50 HD X4 H_16960_015.eps 060407 Figure 8-1 Option codes OP1...OP7 (for all LC7.2E models)
Page 67
Alignments LC7.2E PA EN 67 Option Bit Overview Below find an overview of the Option Codes on bit level. Table 8-5 Option codes at bit level (OP1-OP4) Option Byte & Bit Dec. Value Option Name Description Byte OP1 Bit 7 (MSB)
Page 68
EN 68 LC7.2E PA Alignments Table 8-6 Option codes at bit level (OP5-OP7) Option Byte & Bit Dec. Value Option Name Description Byte OP5 Bit 7 (MSB) NVM_CHECK ON = NVM (range) checking is available OFF = NVM (range) checking is not available...
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC7.2E PA EN 69 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets Introduction Index of this chapter: 9.1 Introduction 9.2 PDP Power Supply The LC7.x (development name “LC07”) is a new global chassis 9.3 DC/DC converters...
Page 70
EN 70 LC7.2E PA Circuit Descriptions, Abbreviation List, and IC Data Sheets Description of the functional blocks (bottom side): • The “Flash Mem” chip contains the software of the TV. • The “Micronas” is the audio demodulator/processor. • The two SDRAM’s are used for the video processing.
Page 71
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC7.2E PA EN 71 DC/DC converters Video CVBS SAW filter IF Demodulator A switch generates the +5.2 V (+5V_SW) from the +5.2 V Audio Tuner SAW filter (+5V_STANDBY) supply voltage. For LCD sets, this switch is mounted on-board the SSB.
Page 72
EN 72 LC7.2E PA Circuit Descriptions, Abbreviation List, and IC Data Sheets Table 9-5 Pin assignment analogue tuners DVB-T Signal Processing Pin number Description DC voltage (V) The DVB-T cell on the SSB is built around the “MOJO” MPEG RF AGC voltage 3.3 - 4.5 (weak or no signal)
Page 73
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC7.2E PA EN 73 • 3.3 V (+3V3_MOJO) During analogue reception, a CVBS signal coming from the • 1.2 V (+1V2_MOJO) analogue front-end is fed to the video processor via pin •...
Page 74
EN 74 LC7.2E PA Circuit Descriptions, Abbreviation List, and IC Data Sheets Audio Processing Principle The audio decoding is done entirely via the Multistandard Sound Processor (MSP) 4450P (item 7411). This processor covers the processing of both analogue and (NICAM) digital input signals by processing the (analogue) IF signal-in to processed (analogue) AF-out (baseband audio).
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC7.2E PA EN 75 HDMI 9.10 Abbreviation List 9.9.1 Introduction 1080i 1080 visible lines, interlaced 1080p 1080 visible lines, progressive scan 2 Carrier Sound Note: Text below is an excerpt from the ”HDMI Specification”...
Page 76
SC1-OUT SCART output of the MSP audio IC LATAM LATin AMerica LC07 Philips chassis name for LCD TV 2007 SC2-OUT SCART output of the MSP audio IC project Short Circuit Liquid Crystal Display Clock signal on I2C bus...
Page 77
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC7.2E PA EN 77 Variable Level out: processed audio output toward external amplifier Video Cassette Recorder Video Graphics Array Watch Dog WYSIWYR What You See Is What You Record: record selection that follows main...
EN 78 LC7.2E PA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.11 IC Data Sheets This section shows the internal block diagrams and pin layouts of ICs that are drawn as "black boxes" in the electrical diagrams (with the exception of "memory" and "logic" ICs).
Page 79
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC7.2E PA EN 79 9.11.2 Diagram B03C, Type STV0700 (IC7K00), PCMCIA Controller Block Diagram Pin Configuration H_16861_001.eps 060307 Figure 9-14 Internal block diagram and pin configuration...
Page 80
EN 80 LC7.2E PA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.11.3 Diagram B03D, Type PNX8314HS (IC7G00), DVB-MOJO Block Diagram 16 bit@133 MHz EJTAG, DSU CPU PR1910 SDRAM interface Fast PI-Bus@120 MHz PI Bridge Central Data Unit Priority int ctrl...
Page 81
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC7.2E PA EN 81 9.11.4 Diagram B04B, Type SVP CX32 (IC7202), Trident Video processor Block Diagram 16/32 5 CVBS UMAC Noise Memory Control Reduction 2 Chroma CRTC PC RGB x 1 10bit Gama...
Page 82
EN 82 LC7.2E PA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.11.5 Diagram B04C, Type MSP4450P (IC7411), Micronas Sound Processor Block Diagram Loud- Sound IF1 Pre- speaker DAC/ modulator processing Sound Sound IF2 High- Processing Resolution Center internal /...
Page 83
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC7.2E PA EN 83 9.11.6 Diagram B06C, Type SIL9025CTU(IC7817), HDMI Receiver Block Diagram Pin Configuration G_16860_073.eps 300107 Figure 9-18 Internal block diagram and pin configuration...
Page 84
EN 84 LC7.2E PA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.11.7 Diagram B06C, Type UDA1334ATS (IC7810), Audio DAC Block Diagram V DDD V SSD PLL0 DIGITAL INTERFACE DATAI DE-EMPHASIS UDA1334ATS SYSCLK/PLL1 SFOR1 MUTE SFOR0 INTERPOLATION FILTER DEEM/CLKOUT NOISE SHAPER...
Page 85
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC7.2E PA EN 85 9.11.8 Diagram B07, Type TDA8932T (IC7A01), Audio Amplifier Block Diagram BOOT1 OSCILLATOR DDP1 IN1P DRIVER HIGH OUT1 CTRL MODULATOR DRIVER SSP1 IN1N MANAGER BOOT2 INREF DDP2 IN2P DRIVER...
EN 86 LC7.2E PA Spare Parts List 10. Spare Parts List Set Level per Model Number (CTN) 0852 IBOZ NVM SW Download from website 2215 2238 586 59812 100nF 20% 50V 0603 1004 9322 246 81682 PDP S50HW-YD05 2216 2020 552 00291 10μF 20% 6V3 0603...