Page 3
Technical Specifications, Connections and Chassis Overview L01.1A GB 3 Audio / Video In 3 - Audio R (0.5 Vrms / 1 k9) CVBS (1 Vpp / 75 9) 1 - Video 2 - Audio L (0.2 Vrms / 10 k9)
Page 4
GB 4 L01.1A Safety & Maintenance Instructions, Warnings, and Notes 2. Safety & Maintenance Instructions, Warnings, and Notes Safety Instructions For Repairs Warnings Safety regulations require that during a repair: • In order to prevent damage to ICs and transistors, avoid •...
Page 5
Directions for Use L01.1A GB 5 3. Directions for Use...
Page 19
Mechanical Instructions L01.1A GB 19 4. Mechanical Instructions Index: Main panel with bracket. 1. Rear Cover Removal 1. Disconnect the strain relief of the AC power cord. 2. Service Position Main Panel 2. Disconnect the degaussing coil by removing the cable 3.
Page 20
GB 20 L01.1A Mechanical Instructions Side I/O Panel Removal 1. Remove the complete Side I/O assembly after unscrewing the two fixation screws [1]. 2. Release the 2 fixation clamps [2] and lift the board out of the bracket. CL 06532012_004.eps...
Page 21
Service Modes, Error Codes and Fault Finding L01.1A GB 21 5. Service Modes, Error Codes and Fault Finding Index: 5.2.1 Service Default Mode (SDM) 1. Test points. 2. Service Modes. Purpose 3. Problems and Solving Tips (related to CSM). •...
Page 22
GB 22 L01.1A Service Modes, Error Codes and Fault Finding 5.2.2 Service Alignment Mode (SAM) After entering SDM, the following screen is visible, with SDM at the upper right side for recognition. Purpose • To perform alignments. • To change option settings.
Page 23
Service Modes, Error Codes and Fault Finding L01.1A GB 23 • In SAM, select menu items with the CURSOR UP/DOWN 6. Indicates if the sleep timer is enabled. key on the remote control transmitter. The selected item 7. Indicates if the V-chip feature is enabled.
Page 24
C2568. Click on the ‘Schematic’ hyperlink to automatically show the position of the highlighted 5.4.1 Introduction capacitor. ComPair (Computer Aided Repair) is a service tool for Philips 5.4.3 How to Connect Consumer Electronics products. ComPair is a further development on the European DST (service remote control), 1.
Page 25
Service Modes, Error Codes and Fault Finding L01.1A GB 25 5.5.1 How to Read the Error Buffer Use one of the following methods: • On screen via the SAM (only if you have a picture). Examples: – ERROR: 0 0 0 0 0 : No errors detected –...
Page 26
GB 26 L01.1A Service Modes, Error Codes and Fault Finding Protections If a fault situation is detected an error code will be generated and if necessary, the set will be put in the protection mode. Blinking of the red LED at a frequency of 3 Hz indicates the protection mode.
Page 27
Alignments L01.1A GB 67 8. Alignments Index: 3. Set the values of NORMAL RED, GREEN and BLUE to 1. General Alignment Conditions 2. Hardware Alignments 4. Go, via the MENU key, to the normal user menu and set 3. Software Alignments and Settings –...
Page 28
GB 68 L01.1A Alignments 5. AUDIO Typenumber OB1 OB2 OB3 OB4 OB5 OB6 OB7 21PT2251/67R 8.3.1 Options 21PT2251/71R 21PT2251/74R 21PT2251/97R 21PT2252/56A 21PT2252/57R 21PT2252/65R S A M 21PT2252/68R 21PT2252/69R 21PT2252/73R 21PT2252/79R O P 1 X X X 21PT2301/67R O P 2...
Page 30
GB 70 L01.1A Alignments Note: Name FM channel can be enabled only when Default setting : 0. FM_RADIO = 1. OP43: STEREO_NICAM_2CS OP26: SMART_PICTURE 0 : For EU and AP_PAL, chip MSP 3415 is not present, 0 : Smart Picture is disabled or not applicable,...
Page 31
Alignments L01.1A GB 71 0 : Smart Text Mode and Favourite Page are disabled or not applicable, OP73: COLOR_SYSTEM_AP 1 : Smart Text Mode and Favourite Page are enabled, This option bit is allocated for AP-PAL colour system Default setting : 1.
Page 32
GB 72 L01.1A Alignments YD (Y-delay) Always set to 8. VERT. SLOPE CL (cathode drive level) Always set to 7. VERT. SHIFT Read only bit, for monitoring purpose only. VERT. AMPLITUDE Read only bit, for monitoring purpose only. 8.3.3 White Tone V.S-CORRECTION...
Page 33
Alignments L01.1A GB 73 • Lower Corner Parabola (LCP) Align straight vertical lines in the lower corners of the screen. In the table below, you will find the GEOMETRY default • East West Trapezium (EWT) Align straight vertical lines values for the different sets.
Page 34
GB 74 L01.1A Circuit Description 9. Circuit Description Index: 1. Introduction The L01 is divided into 2 basic systems, i.e. mono and stereo 2. Audio Signal Processing sound. While the audio processing for the mono sound is 3. Video Signal Processing done in the audio block of the UOC, an external audio 4.
Page 35
Circuit Description L01.1A GB 75 9.2.2 Mono 9.3.3 Video Source Selection In mono sets, the signal goes via the SAW filter (position The Composite Video Blanking Signal (CVBS) from buffer 1004 in case of QSS demodulation and 1003 in case of...
Page 36
GB 76 L01.1A Circuit Description (but less than 3 V), the RGB signals at pins 51, 52 and 53 are this purpose is the DC voltage on pin 54 (BLCIN) of the inserted into the picture by using the internal switches.
Page 37
Circuit Description L01.1A GB 77 Deflection driver device (IC7200) delivers output currents, R3474 and R3475 convert them to voltage. The differential input voltage is compared with the voltage across measuring resistor 9.5.1 Horizontal Drive R3471 that provides internal feedback information. The...
GB 78 L01.1A Circuit Description format, 16:9, 14:9, 16:9 zoom, subtitle zoom and the Super- Wide picture format SUPPLY START-UP V CC DRAIN MANAGEMENT CURRENT SOURCE A line, written at the upper- or lower side of the screen, will clamp...
Page 39
Circuit Description L01.1A GB 79 Degaussing Control Circuit B1/B2 n⋅V Main Supply Focus Mains AC Input Main Power Panel VideoSupply Supply Main Aux Filament Tilt& Rotation GATE Degaussing Circuit VlotAux +13V 3V3 Reg. Correction Horizontal GATE Vaux Deflection +3.9V +3.3V...
Page 40
GB 80 L01.1A Circuit Description The moment that the voltage on pin 1 drops below the ‘under voltage lock out‘ level (UVLO = ± 9 V), the IC will stop switching and will enter a safe restart from the rectified mains voltage.
Page 41
Circuit Description L01.1A GB 81 • When the set is in protection mode. In Standby, the power supply works in ‘burst mode’. Active/ Burst mode can be used to reduce the power consumption inactive below 1 W at stand-by. During this mode, the controller is...
Page 42
GB 82 L01.1A Circuit Description Over Power Protection 9.7.1 Introduction During the primary stroke, the rectified AC input voltage is measured by sensing the current drawn from pin 4 (DEM). The microprocessor part of the UOC, has the complete This current is dependent on the voltage on pin 9 of control and teletext on board.
Page 43
Circuit Description L01.1A GB 83 presence of an external Y/C source makes this line ‘high’ transistor TS7606 (in A7 diagram) will conduct and while a CVBS source makes the line ‘low’. UOC is triggered to shut down the power supply.
Page 44
GB 84 L01.1A Circuit Description External (source), entering the set time, creating a double vertical via SCART or Cinch resolution. Fast Blanking: DC signal Picture Tube Panel (or CRT-panel) accompanying RGB signals Random Access Memory FILAMENT Filament of CRT Remote Control handset...
Page 49
Block Diagram, Testpoints, I2C And Supply Voltage Overview L01.1A 6. Block Diagram, Testpoints, I C And Supply Voltage Overview Block Diagram SIDE AV SIDE AV FRONT I/O AUDIO/VIDEO BTSC-NDBX AUDIO AMPLIFIER FRONT CONTROL CONTROL +3.3V +3.3V SOURCE SWITCHING STEREO DECODER...
Page 50
Block Diagram, Testpoints, I2C And Supply Voltage Overview L01.1A Testpoint Overview Main Panel Copper Track side AUDIO OUTPUT 7901 OR 7902 2V / div DC 1V / div DC 50V / div DC TV-PROC. 20us / div 10us / div 10us / div P1 = "$"...
Page 51
Block Diagram, Testpoints, I2C And Supply Voltage Overview L01.1A I2C And Supply Voltage Diagram POWER SUPPLY LINE DEFLECTION 5445 ANODE CRT 5500 : 6500 FOCUS FOCUS 6560 MAIN SUPPLY FOCUS CRT 5560 5564 5561 3487 5451 0211 0231 5502 GBU6J...
Page 52
Schematics and PWB’s L01.1A 7. Schematics and PWB’s Large Signal Panel: Power supply 0211 C1 5521 D7 0212 A1 5560 D8 0213 B5 5561 D10 POWER SUPPLY 0231 B1 5562 C8 VlotAux+13V 0251 E11 5564 D9 2581 For AV Video...
Page 53
Schematics and PWB’s L01.1A Large Signal Panel: Line Deflection 0220 A2 3488 C9 0221 B6 3489 C3 1400 B4 3490 B9 LINE DEFLECTION 2400 F4 3491 C2 9453 EHTinfo 2401 F4 3492 C2 9451 1.9V A2-16 2402 F4 3493 C2...
Page 56
Schematics and PWB’s L01.1A Large Signal Panel: Video IF + Sound IF 0243 C6 4212 B2 (LATAM / NAFTA / AP) 0248 C2 4213 A2 VIDEO IF + SOUND IF 0249 B2 4214 D10 0266 E11 4216 F9 3221 3222...
Page 62
Schematics and PWB’s L01.1A Large Signal Panel: Front I/O + Front Control + Headphone 0214 F9 0215 C4 FRONT IO + FRONT CONTROL + HEADPHONE 0218-A C2 0218-B C2 0218-C B2 0219 D4 0232 F5 0259 F10 0270 B5 FRONT CINCH...
Page 63
Schematics and PWB’s L01.1A Large Signal Panel: Rear I/O Cinch 0223-A A10 4104 B3 0223-B F2 4121 E6 0223-C C2 4131 C9 REAR I/O CINCH 0223-D A2 7101 A6 FOR ITV - TO 0227 OF 0225-A D10 7102 D2 0225-B D9...
Page 66
Schematics and PWB’s L01.1A Layout Large Signal Panel (Top View) CL 16532053_005.eps 050601...
Page 67
Schematics and PWB’s L01.1A Layout Large Signal Panel (Mapping Top View) Layout Large Signal Panel (Overview Bottom View) Part 1 CL 16532053_06a.eps Part 2 CL 16532053_06b.eps Part 3 Part 4 CL 16532053_06c.eps CL 16532053_06d.eps CL 16532053_006.eps 100701 CL 16532053_05m.eps 100701...
Page 68
Schematics and PWB’s L01.1A Layout Large Signal Panel (Part 1 Bottom View) Part 1 CL 16532044_86a.eps 310501...
Page 69
Schematics and PWB’s L01.1A Layout Large Signal Panel (Part 2 Bottom View) Part 2 CL 16532053_06b.eps 310501...
Page 70
Schematics and PWB’s L01.1A Layout Large Signal Panel (Part 3 Bottom View) Part 3 CL 16532053_06c.eps 040601...
Page 71
Schematics and PWB’s L01.1A Layout Large Signal Panel (Part 4 Bottom View) Part 4 CL 16530153_06d.eps 050601...