All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by WS 0763 BG CD Customer Service...
EN 2 EJ3.0U PA Technical Specifications, Connections, and Chassis Overview 1. Technical Specifications, Connections, and Chassis Overview Index of this chapter: 1.1.2 Sound 1.1 Technical Specifications 1.2 Connection Overview Sound systems : AV Stereo 1.3 Chassis Overview : BTSC : Dolby Digital (AC3) Notes: Maximum power (W : 2 x 15...
Page 3
Technical Specifications, Connections, and Chassis Overview EJ3.0U PA EN 3 1.2.1 Side Connections USB1.1 HDMI 1 & HDMI 2: Digital Video, Digital Audio - In E_06532_017.eps 250505 E_06532_022.eps 300904 Figure 1-3 HDMI (type A) connector Figure 1-2 USB (type A) - D2+ Data channel - Shield...
Page 4
EN 4 EJ3.0U PA Technical Specifications, Connections, and Chassis Overview Chassis Overview AMBILIGHT INTER- CONNECTION PANEL CONTROL PANEL IR / LED PANEL SMALL SIGNAL BOARD SIDE I/O PANEL H_17000_017.eps 270207 Figure 1-4 PWB/CBA locations...
• Be careful during measurements in the high voltage • Use only lead-free soldering tin Philips SAC305 with order section. code 0622 149 00106. If lead-free solder paste is required, • Never replace modules or other components while the unit please contact the manufacturer of your soldering is switched "on".
Mix of lead-free soldering tin/parts with leaded soldering If a PDP has defective or "dead" pixels, do the following: tin/parts is possible but PHILIPS recommends strongly to 1. Locate the defective pixels. avoid mixed regimes. If this cannot be avoided, carefully 2.
Mechanical Instructions EJ3.0U PA EN 7 4. Mechanical Instructions Index of this chapter: Notes: 4.1 Cable Dressing • Several models in this chassis range have a different 4.2 Service Positions mechanical construction, the instructions given in this 4.3 Assy/Panel Removal chapter are therefore very model specific.
Page 8
EN 8 EJ3.0U PA Mechanical Instructions Service Positions Assy/Panel Removal For easy servicing of this set, there are a few possibilities 4.3.1 Rear Cover created: • The buffers from the packaging. Warning: Disconnect the mains power cord before you remove •...
Page 9
Mechanical Instructions EJ3.0U PA EN 9 4.3.3 Keyboard Control Panel [E] 1. Refer to next fig. “Keyboard control panel“. 2. Remove the T10 Parker screws [1] from the shielding. 3. Remove the shielding. 4. Remove the T10 Parker screws [2] from the bracket. 5.
Page 10
EN 10 EJ3.0U PA Mechanical Instructions 4.3.7 Power Supply Board 4. You now view the PDP boards, as shown in fig. “PDP panel [2/3]“ below. 5. Remove fixation screws [3] and lift the complete PDP (incl. The PSU belongs to the PDP panel. Please refer to the PDP the boards and wiring) by means of the mounting brackets repair manual for more info.
Page 11
Mechanical Instructions EJ3.0U PA EN 11 4.3.11 Glass Plate 1. Refer to figures “Glass plate“ below. 2. Remove T10 Parker screws [1] along the side of the glass plate, and remove the metal fixation brackets. 3. Lift the glass plate form the set. H_17000_016.eps 280207 Figure 4-15 Glass plate...
EN 12 EJ3.0U PA Service Modes, Error Codes, and Fault Finding 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: • Tuning frequency 61.25 MHz for NTSC: The TV shall tune 5.1 Test Points to physical channel 3 only if channel 3 is an analog channel 5.2 Service Modes or if there is no channel 3 installed in the channel map.
Page 13
Code version number (a higher number is always compatible with a lower number). The last two 39mm digits are used for development reasons only, so PHILIPS they will always be zero in official releases. MODEL: 32PF9968/10 • NNNNN= last five digits of 12nc code of the PROD.SERIAL NO:...
Page 14
SC BL 1080p 1920 under development LC420WU5-SLA1 reserved Sharp 1080p 1920 under development LK370D3LZXX 768p 1366 reserved 768p 1366 under development WX5 SLB1 1080p 1920 under development E_06532_030a.eps 080207 Figure 5-3 Display option code overview [1/2] (for all Philips FTV chassis)
Page 15
LC420WX5-SLD1 9322 249 09682 E_06532_030b.eps 080207 Figure 5-4 Display option code overview [2/2] (for all Philips FTV chassis) • Store. All options and alignments are stored when Note: As long as SAM is activated, it is not possible to change pressing “cursor right”...
Page 16
EN 16 EJ3.0U PA Service Modes, Error Codes, and Fault Finding 5.2.3 Customer Service Mode (CSM) – 3.2. Dolby: Indicates whether the received transmitter transmits Dolby sound (“ON”) or not (“OFF”). Attention: The presence of Dolby can only be tested by the Purpose software on the Dolby Signaling bit.
Page 17
Service Modes, Error Codes, and Fault Finding EJ3.0U PA EN 17 • CSM 7: – 8.1. 12NC one zip SW: Displays the 12NC number of – 7.2. TV System: Gives information about the video the one-zip file as it is used for programming software system of the selected transmitter.
Page 18
EN 18 EJ3.0U PA Service Modes, Error Codes, and Fault Finding Stand by or Protection Mains is applied action holder: MIPS Standby Supply starts running. +5V2, 1V2Stb, 3V3Stb and +2V5D become present. In case of PDP 3V3 Vpr to CPU PDP becomes present. action holder: St-by autonomous action st-by µP resets...
Page 19
Service Modes, Error Codes, and Fault Finding EJ3.0U PA EN 19 From part A From part A From part A From part A action holder: MIPS activate +8V6 supply action holder: St-by +8V6 error Start polling the detect-1V2 every 40ms detection algorithm autonomous action return...
Page 20
EN 20 EJ3.0U PA Service Modes, Error Codes, and Fault Finding From part A From part B From part B From part B action holder: MIPS action holder: St-by Flash to Ram image transfer succeeded autonomous action within 30s? Code = 5 Viper SW initialization Switch Viper in reset Code = 53...
Page 21
Service Modes, Error Codes, and Fault Finding EJ3.0U PA EN 21 PDP SDI [42"/50" V5, W1 & W2, or 63" V4] action holder: MIPS action holder: St-by autonomous action Semi Standby Assert RGB video blanking and audio mute Initialize audio and video processing IC's and functions according needed use case.
Page 22
EN 22 EJ3.0U PA Service Modes, Error Codes, and Fault Finding PDP SDI [42"/50" V5, W1 & W2, or 63" V4] action holder: MIPS Active action holder: St-by autonomous action Mute all sound outputs. Switch reset-audio and sound-enable lines “high” Blank PDP display Mute all video outputs Wait 600ms to prevent image...
Page 23
Service Modes, Error Codes, and Fault Finding EJ3.0U PA EN 23 Semi Stand by action holder: MIPS action holder: St-by Delay transition until ramping down of ambient light is finished. *) autonomous action *) If this is not performed and the set is Switch ambient light to passive mode with RGB switched to standby when the ramping of values on zero.
Page 24
EN 24 EJ3.0U PA Service Modes, Error Codes, and Fault Finding Log the appropriate error and action holder: MIPS set stand-by flag in NVM action holder: St-by Redefine wake up reasons for protection autonomous action state and transfer to stand-by µP. Switch off LCD lamp supply If needed to speed up this transition, Wait 250ms (min.
Page 25
Introduction whether the Small Signal Board (SSB) or the display of a Flat ComPair (Computer Aided Repair) is a Service tool for Philips TV is defective. Thus to determine if LVDS, RGB, and sync Consumer Electronics products. and offers the following: signals are okay.
Page 26
EN 26 EJ3.0U PA Service Modes, Error Codes, and Fault Finding Error Codes 5.5.2 How to Read the Error Buffer Use one of the following methods: 5.5.1 Introduction • On screen via the SAM (only if you have a picture). E.g.: –...
Page 27
Service Modes, Error Codes, and Fault Finding EJ3.0U PA EN 27 Extra Info • Error 44 (NVM). This error will never occur because it is • Error 1 (I C bus 1 blocked). When this error occurs, the masked by error 3 (I C bus 3).
Page 28
EN 28 EJ3.0U PA Service Modes, Error Codes, and Fault Finding Protections 5.8.4 DC/DC Converter Introduction 5.7.1 Software Protections • The best way to find a failure in the DC/DC converters is to check their starting-up sequence at power "ON" via the Most of the protections and errors use either the stand-by Mains/AC Power cord, presuming that the Stand-by microprocessor or the VIPER controller as detection device.
Page 29
Disconnect the TV from the Mains/AC Power. Table 5-4 SSB service kits (for EJ3.0U LA chassis) • Press the “OK” button on a Philips DVD RC-6 remote control (it is also possible to use the TV remote in "DVD" Model Number New SSB order code mode).
Page 30
EN 30 EJ3.0U PA Service Modes, Error Codes, and Fault Finding – MCSUM=0x0000 – 7. If you do not see the above info, restart the above procedure, and check your HyperTerminal settings and the connections between PC and TV. 8. Via “Transfer” -> “Send text file ...”, you can send the proper upgrade file to the TV.
Block Diagrams, Test Point Overviews, and Waveforms EJ3.0U PA Test Point Overview SSB (Overview Top Side) Personal Notes: IQ08 D3 IQ08 D3 I293 D3 IQ09 C2 I303 B3 IQ09 C3 I304 B2 IQ10 D3 I305 B2 IQ14 D2 I306 B3 IQ14 D2 I307 D3 IQ15 D1...
Page 36
Block Diagrams, Test Point Overviews, and Waveforms EJ3.0U PA Test Point Overview SSB (Part 1 Top Side) Part 1 G_16840_068a.eps 220107...
Page 37
Block Diagrams, Test Point Overviews, and Waveforms EJ3.0U PA Test Point Overview SSB (Part 2 Top Side) Part 2 G_16840_068b.eps 220107...
Page 38
Block Diagrams, Test Point Overviews, and Waveforms EJ3.0U PA Test Point Overview SSB (Overview Bottom Side) AH11 C3 F201 E3 FG02 E3 FT12 A1 I157 A3 I266 F2 I385 A4 IC09 B1 IJ27 B3 IU22 F3 AJ10 C3 F202 E3 FG03 E3 FT15 A2 I158 A2...
Page 39
Block Diagrams, Test Point Overviews, and Waveforms EJ3.0U PA Test Point Overview SSB (Part 1 Bottom Side) Part 1 G_16840_069a.eps G_16840_069a.eps 220107...
Page 40
Block Diagrams, Test Point Overviews, and Waveforms EJ3.0U PA Test Point Overview SSB (Part 2 Bottom Side) Part 2 G_16840_069b.eps G_16840_069b.eps 220107...
Block Diagrams, Test Point Overviews, and Waveforms EJ3.0U PA Test Point Overview AmbiLight Inter Connect Panel (Bottom Side) G_16840_079.eps 3139 123 6231.1 230107...
Circuit Diagrams and PWB Layouts EJ3.0U PA SSB: Audio: Connectors SSB: SRP List Explanation Example 0M98 C6 1.1. Introduction Net Name Diagram 0M99 C6 AUDIO: CONNECTORS B08B B08B 1740 C1 +12-15V AP1 (4x) +12-15V AP4 (4x) SRP (Service Reference Protocol) is a software tool that creates a list with all references to signal lines. The list contains 1M02 A1 +12-15V AP5 (12x)
Alignments EJ3.0U PA EN 95 8. Alignments Index of this chapter: • US/AP-NTSC models: an NTSC M/N TV-signal with a 8.1 General Alignment Conditions signal strength of at least 1 mV and a frequency of 61.25 8.2 Hardware Alignments MHz (channel 3). 8.3 Software Alignments •...
Page 96
EN 96 EJ3.0U PA Alignments Table 8-1 White D alignment values Color Temp. Cool Normal Warm (degr. K) (11500) (9100) (6500) 0.275 0.287 0.314 0.276 0.292 0.320 When such equipment is not available, use “method 2”. Method 2 (without color analyzer): If you do not have a color analyzer, you can use the default values.
Page 97
Inverted Class D amplifier Yes / No Feature present / not present Miscellaneous Region ATSC / DVB-T Feature present Alternative Tuner Philips Tuner brand Tuner Type TD1336S / TD 1331 Tuner type AGC amplifier Other / Sanyo Hotel mode Off / On...
Page 98
EN 98 EJ3.0U PA Alignments 8.4.4 Option Numbers Select this sub menu to set all options at once (expressed in two long strings of numbers). An option number (or "option byte") represents a number of different options. When you change these numbers directly, you can set all options very quickly.
Page 99
3 (8) Interconnect China IF 0= Off, 8= On 4 (16) Alternative Tuner 0= Philips, 16= Alps Tuner make. 5 (32) Tuner Type 0= TD1336s (B-Chassis US), 32= TD1331(J-Chassis US), Tuner type 64= UV1318 (Analogue EU), 96= TD1316 (Hybrid EU) (B-chassis US is e.g "BP2.3U").
Page 100
EN 100 EJ3.0U PA Alignments Byte Bit (dec. value) Subject Options Settings (in decimal values) Remarks 0 (1) Display Screen type See table “Display code overview” in chapter “Service Modes” for the values. Screen size, type, and resolution. 1 (2) 2 (4) 3 (8) 4 (16)
Circuit Descriptions, Abbreviation List, and IC Data Sheets EJ3.0U PA EN 101 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets Index of this chapter: Signal Processing 9.1 Introduction The AVIP together with the MPIF device is used to perform the 9.2 Abbreviation List input decoding of a single stream of analog audio and video 9.3 IC Data Sheets...
Page 102
EN 102 EJ3.0U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets G_16840_017.eps 110107 Figure 9-2 Block diagram AmbiLight interconnect board G_16840_019.eps 110107 Figure 9-3 Backlight dimming jumper settings...
Page 103
Circuit Descriptions, Abbreviation List, and IC Data Sheets EJ3.0U PA EN 103 SSB Cell Layout LVDS SIGNAL PROCESSING DC/DC & CONV. MPIF TUNER SOURCE SELECTION G_16840_015.eps 010207 Figure 9-4 SSB top view AVIP COLUMBUS STBY CONTROLLER VIPER SOURCE SELECTION HDMI RECEIVER G_16840_016.eps 010207...
EN 104 EJ3.0U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets Abbreviation List emergency information to digital terminal devices Entitlement Control Message AARA Automatic Aspect Ratio Adaptation: E-DDC Enhanced Display Data Channel algorithm that adapts aspect ratio to (VESA standard for communication remove horizontal black bars;...
Page 105
Not Connected Sync On Green Negative Temperature Coefficient, SOPS Self Oscillating Power Supply non-linear resistor S/PDIF Sony Philips Digital InterFace NTSC National Television Standard SRAM Static RAM Committee. Color system mainly used Small Signal Board in North America and Japan. Color...
EN 106 EJ3.0U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets IC Data Sheets This section shows the internal block diagrams and pin configurations of ICs that are drawn as "black boxes" in the electrical diagrams (with the exception of "memory" and "logic" ICs).
Page 107
Circuit Descriptions, Abbreviation List, and IC Data Sheets EJ3.0U PA EN 107 9.3.2 Diagram B02A, NXT2004 (IC 7T22) Block Diagram VSB/QAM MPEG IF In text text text Demodulator Transport Sense 32K x 8 text BERT text RF Gain SRAM text IF AGC RF AGC µC...
Page 108
EN 108 EJ3.0U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.3.3 Diagram B03A/B/C/D, PNCX3000 (IC 7A00) Block Diagram 1 × CVBSOUTA CVBSOUTB 2NDSIFEXT (FMRAD) CVBSOUTIF SIFAGC MIXER SIFIN 2nd SIF internal & AM SND DEMOD DTV 1st IF DTVOUT SWITCH VIFIN...
Page 109
Circuit Descriptions, Abbreviation List, and IC Data Sheets EJ3.0U PA EN 109 9.3.4 Diagram B04A/B/C/D/E/F, PNX2018 (IC 7J00) Block Diagram 16-BIT 200 MHz DDR PNX2018 MEMORY CONTROLLER video NORTH TUNNEL SOUTH TUNNEL PNX8554 co-processor direct sream dual or single HD input (TDA9975) MEMORY VO-1...
Page 110
EN 110 EJ3.0U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.3.5 Diagram B05A/B/C/D, PNX8552 (IC 7V00) Block Diagram Streaming Interface Optional External 32-Bit 225 MHz DDR from Tunnel Video Improvement Processing PNX8550 Memory 30 (dig) DVD-CSS 5-Layer Controller Primary Tunnel Video Out...
Page 111
Circuit Descriptions, Abbreviation List, and IC Data Sheets EJ3.0U PA EN 111 9.3.6 Diagram B05F, LD3985M (IC 7M05 & 7M06) Block Diagram Pin Configuration TSOT23-5L/SOT23-5L Flip-Chip G_16290_084.eps 020206 Figure 9-11 Internal block diagram and pin configuration...
Page 112
EN 112 EJ3.0U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.3.7 Diagram B06, MOP XC3S400 (IC 7G00) Pin Configuration IO_L01P_7/VRN_7 IO_L01N_2/VRP_2 Bank 0 Bank 1 IO_L01N_7/VRP_7 IO_L01P_2/VRN_2 IO_L21P_7 IO_L21N_2 IO_L21N_7 IO_L21P_2 VCCO_2 VCCO_7 VCCAUX VCCINT IO_L23P_7 IO_L24N_2 IO_L23N_7 IO_L24P_2 IO_L40P_7 IO_L40N_2...
Page 113
Circuit Descriptions, Abbreviation List, and IC Data Sheets EJ3.0U PA EN 113 9.3.8 Diagram B07B, TDA9975HS (IC 7B50) Block Diagram τ ORR/V τ I²C ORB/U τ ORG/Y G/Pb B/Pb1 B/Pb2 B/Pb3 I²C 10/12 I²C I²C CLAMP BIAS I²C I²C I²C I²C I²C BIAS...
Page 114
EN 114 EJ3.0U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.3.9 Diagram B07E, AD8190ACPZ (IC 7C01) Block Diagram Pin Configuration G_16840_098.eps 090207 Figure 9-14 Internal block diagram and pin configuration...
Page 115
Circuit Descriptions, Abbreviation List, and IC Data Sheets EJ3.0U PA EN 115 9.3.10 Diagram M1, NCP5422AD (IC 7101) See figure “Diagram B01A, NCP5422A (IC 7U00)“. 9.3.11 Diagram M2, PACIFIC3-N2 T6TF4HFG (IC 7202) Block Diagram Contrast Reserve Input Proc Contr, Brightness &...
Page 116
EN 116 EJ3.0U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.3.12 Diagram M2, P87LPC760BDH (IC 7203) BLOCK DIAGRAM ACCELERATED 80C51 CPU INTERNAL BUS UART 1 KBYTE CODE EPROM 128 BYTE DATA RAM TIMER 0, 1 PORT 2 CONFIGURABLE I/OS PORT 1 CONFIGURABLE I/OS WATCHDOG TIMER...
Spare Parts List EJ3.0U PA EN 117 10. Spare Parts List Set Level per Model Number (CTN) 2A10 2238 787 15641 22nF 5% 16V 0402 2B41 4822 124 12108 100μF 20% 4V 2A11 2238 787 15641 22nF 5% 16V 0402 2B45 2222 780 15663 1μF 10% 0805 2A13...