Daikin RXSQ24TAVJU Service Manual page 105

SiUS331708EA
Mode First
No. Code
(∗2) No.
0 Setting of airflow rate
Airflow direction setting
1
(Set when a blocking pad kit has been installed.)
2 (∗9) Swing pattern settings
3 (∗13) Operation of downward flow flap
13(23)
4 Setting of airflow direction adjustment range
5 (∗10) CFM table setting
5 (∗12) Setting of static pressure selection
6 External static pressure settings
Optional kit setting (UV lamp + humidifier +
4 (∗11)
economizer)
5 (∗11) Residential dry
14
(24)
9 (∗13) Mold proof operation setting
11 (∗10) Gas furnace test mode
0 Drain pump operation settings
1 Humidification when heating thermostat is OFF
Setting of direct duct connection
(when the indoor unit and energy recovery
2
15(25) ventilator unit are connected by duct directly.)
(∗5)
Interlocked operation between humidifier and
3
drain pump
5 Individual setting of ventilation
1b 3 Display of contact center
4 Display of error codes on the remote controller
12 Key-lock pattern settings
14 Setting "restricted / permitted" of airflow block
1c 0 Room temperature display
Notes :
1. Settings are made simultaneously for the entire group, however, if you select the mode No. inside
parentheses, you can also set by each individual unit. Setting changes however cannot be checked except in
the individual mode for those in parentheses.
∗2. The mode numbers inside parentheses cannot be used by wireless remote controllers, so they cannot be set
individually. Setting changes also cannot be checked.
3. Do not make settings other than those described above. Nothing is displayed for functions the indoor unit is
not equipped with.
4. 88 or Checking the connection. Please stand by. may be displayed to indicate the remote controller is
resetting when returning to the normal mode.
∗5. If the setting mode to "Equipped", energy recovery ventilator fan conducts the fan residual operation by
linking to indoor unit.
∗6. Only for FXTQ-TA models
∗7. Only for FXDQ-M, FXTQ-TA, CXTQ-TA models
∗8. If the airflow setting when thermostat is OFF is set to OFF (12(22)-3-03, 12(22)-6-03), the air in the indoor
unit will be stagnant and suction air thermistor may not detect room temperature correctly, resulting in
problems that thermostat will not be ON easily.
Use optional remote sensor in such conditions, or set the field setting 10(20)-2 to 03 (only remote controller
thermistor).
∗9. Only for FXFQ-T and FXUQ-P sensing models
∗10.Only for CXTQ-TA models
∗11.Only for FXTQ-TA and CXTQ-TA models
∗12.Only for FXDQ-M models
∗13.Only for FXEQ-P models
∗14.Only for FXZQ-TA and FXSQ-TA models
Field Settings and Test Operation
Setting Contents
Second Code No.
01
Refer to page 103 for details.
F (4 directions) T (3 directions)
All direction
synchronized swing
Equipped Not equipped
Draft prevention Standard
Standard
Standard High static pressure
Refer to page 105 for details.
Refer to page 106 for details.
Set temperature:
Set temperature:
same as cooling set
room temperature
temperature
For high humidity
Standard
areas
OFF Low heat
—
Not equipped Equipped
Not equipped Equipped
Not interlocked Interlocked
Not individual Individual
Displayed Not displayed
— Two-digit display
No operation No operation
allowed (Cancel allowed (Cancel
procedure is procedure is not
displayed.) displayed.)
Refer to page 108 for details.
Room temperature Room temperature
is not displayed is displayed
Field Settings from Remote Controller
02 03
W
(2 directions)
— Facing swing
—
Ceiling soiling
prevention
Low —
—
—
—
High heat
ON OFF
—
—
—
—
—
—
No menu
operation is
allowed
(Cancel
procedure is
displayed.)
—
04
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Four-digit
display
No menu
operation is
allowed any
time.
—
92