WAGO 750 Manual
Fieldbus independent i/o modules
Hide thumbs
Also See for 750:
- User manual ,
- Manual (450 pages) ,
- User's installation and configuration (335 pages)
Subscribe to Our Youtube Channel
Related Manuals for WAGO 750
Summary of Contents for WAGO 750
- Page 1 Fieldbus Independent I/O Modules 2 AO 0-10V DC 10Bit 10mA 24V 750-560 Manual Version 1.0.3...
- Page 2 • General Copyright 2007 by WAGO Kontakttechnik GmbH & Co. KG All rights reserved. WAGO Kontakttechnik GmbH & Co. KG Hansastraße 27 D-32423 Minden Phone: +49 (0) 571/8 87 – 0 Fax: +49 (0) 571/8 87 – 1 69 E-Mail: info@wago.com...
-
Page 3: Table Of Contents
Number Notation..................5 Safety Notes ..................... 6 Scope ......................6 2 I/O Modules ....................7 Analog Output Modules ................7 2.1.1 750-560 [2 AO 0-10V DC 10Bit 10mA 24V] ........7 2.1.1.1 View....................7 2.1.1.2 Description..................7 2.1.1.3 Display Elements ................8 2.1.1.4... -
Page 4: Important Comments
WAGO Kontakttechnik GmbH & Co. KG declines all liability resulting from improper action and damage to WAGO products and third party products due to non-observance of the information contained in this manual. -
Page 5: Symbols
Routines or advice for efficient use of the device and software optimization. More information References on additional literature, manuals, data sheets and INTERNET pages 1.3 Number Notation Number Code Example Note Decimal normal notation Hexadecimal 0x64 C notation Binary '100' Within ', '0110.0100' Nibble separated with dots WAGO-I/O-SYSTEM 750 I/O Modules... -
Page 6: Safety Notes
1.5 Scope This manual describes the Analog Output Module 750-560 2 AO 0-10V DC 10Bit 10mA 24V of the modular WAGO-I/O-SYSTEM 750. Handling, assembly and start-up are described in the manual of the Fieldbus Coupler. Therefore this documentation is valid only in the connection with the appropriate manual. -
Page 7: O Modules
2.1.1.2 Description The analog output module 750-560 creates a standardized signal of 0-10 V. The module has two short circuit protected output channels and enables, for example, the direct wiring of two 3-conductor actuators to the connections AO 1, AC/DC 24 V and 0 V or AO 2, AC/DC 24 V and 0 V. The signals are transmitted via AO 1 and AO 2. -
Page 8: Display Elements
However, if such a case should occur, another supply module must be added. The analog output module 750-560 can be used with all couplers/controllers of the WAGO-I/O-SYSTEM 750 (except for the economy types 750-320, - 323, -324 and -327). -
Page 9: Schematic Diagram
750-560 [2 AO 0-10V DC 10Bit 10mA 24V] • 9 Schematic Diagram 2.1.1.4 Schematic Diagram Logic AO 1 AO 2 270 pF Error 24 V Function 24 V 10 nF 10 nF Shield Shield (screen) (screen) 750-560 Fig. 2.1.1-3: 2-Channel Analog Output Module 750-560... -
Page 10: Technical Data
Approvals (cf. Chapter 2.2 of the Coupler/Controller Manual) Conformity Marking More Information Detailed references to the approvals are listed in the document "Overview Approvals WAGO-I/O-SYSTEM 750", which You can find on the CD ROM ELECTRONICC Tools and Docs (Item-No.: 0888-0412-0001-0101) or in the Internet under: www.wago.com ->... -
Page 11: Process Image
Process Image 2.1.1.6 Process Image The analog output module 750-560 transmits 16-bit data and 8 status bits per channel. The digitalized output value is transmitted in a data word (16 bits) as output byte 0 (low) and output byte 1 (high) via the process image of the coupler / controller. - Page 12 WAGO Kontakttechnik GmbH & Co. KG Postfach 2880 • D-32385 Minden Hansastraße 27 • D-32423 Minden Phone: 05 71/8 87 – 0 Fax: 05 71/8 87 – 1 69 E-Mail: info@wago.com Internet: http://www.wago.com...
Need help?
Do you have a question about the 750 and is the answer not in the manual?
Questions and answers