1. Manuals
  2. Brands
  3. Raven Manuals
  4. Controller
  5. RCM ARAG Bravo
  6. Installation manual

Raven RCM ARAG Bravo Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
RCM ARAG Installation
Manual
016-7100-001 Rev. A
11/2020
E36341
Copyright 2020

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RCM ARAG Bravo and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Raven RCM ARAG Bravo

Summary of Contents for Raven RCM ARAG Bravo

  • Page 1 RCM ARAG Installation Manual 016-7100-001 Rev. A 11/2020 E36341 Copyright 2020...
  • Page 2 Raven systems, or products used as components of systems, which rely upon the reception of these signals or availability of these services. Raven Industries accepts no responsibility for the use of any of these signals or services for other than the stated purpose.

  • Page 3: Table Of Contents

    Table of Contents Chapter 1 Important Information..................1 Safety ....................................1 Displays and Control Consoles ............................1 Electrical safety ..................................2 Touch Screen .................................... 2 Recommendations and Best Practices ........................ 2 Harness Routing ..................................2 Chapter 2 Introduction......................5 Installation Best Practices ............................5 Recommendations .................................
  • Page 4 Table of Contents RCM ARAG Installation Manual...

  • Page 5: Chapter 1 Important Information

    • Do not operate this Raven system or any agricultural equipment while under the influence of alcohol or an illegal substance. • Be alert and aware of surroundings and remain in the operator seat at all times when operating this Raven system.

  • Page 6: Electrical Safety

    • Do not connect the power leads to the battery until all system components are mounted and all electrical connections are completed. • Always start the machine before initializing this Raven system to prevent power surges or peak voltage. • To avoid tripping and entanglement hazards, route cables and harnesses away from walkways, steps, grab bars, and other areas used by the operator or service personnel when operating or servicing the equipment.
  • Page 7 IMPORTANT INFORMATION • Avoid abrasive surfaces and sharp edges such as sheared or flame cut corners, fastener threads or cap screw heads, hose clamp ends, etc. • Do not connect, affix, or allow harnessing to come into contact with components with high vibration forces, hot surfaces, or components carrying hot fluids beyond the temperature rating of harness components.
  • Page 8 CHAPTER 1 RCM ARAG Installation Manual...

  • Page 9: Introduction

    C H A P T E R 2 The Raven Rate Control Module (RCM) is a multi-product application control system built on an ISOBUS platform. The Raven Rate Controller Module is designed to provide a machine operator the ability to simultaneously monitor and control five product applications such as liquid, granular, NH3, and direct injection via ISOBUS Universal Terminal (UT) and task control for as-applied documentation, prescription rate, and section control.

  • Page 10: Kit Components

    If you have questions about the kit, contact your Raven dealer. FIGURE 1. RCM ARAG Bravo 180S 3 Sections, 2-Wire Valves Kit Components (P/N 117-7100-039 Rev. A) PART #...

  • Page 11: Updates

    Applied Technology Division web site: https://portal.ravenprecision.com Sign up for e-mail alerts to receive notifications when updates for your Raven products are available on the Raven web site. At Raven Industries, we strive to make your experience with our products as rewarding as possible.
  • Page 12 CHAPTER 2 RCM ARAG Installation Manual...

  • Page 13: Installation

    I NSTALLATION CHAPTER C H A P T E R 3 NOTE: To install the steering kit with an SC1 system, please refer to the CRx/Viper 4+ SC1/TC1 Installation Manual (P/N 016-8000-014) To install the steering kit with an RS1 system, please refer to the CRx/Viper 4+ RS1 Installation Manual (P/N 016-8000-028) POWER HARNESS BEST MOUNTING PRACTICES...

  • Page 14: Mount The Power Harness

    CHAPTER 3 MOUNT THE POWER HARNESS When installing an auto-steer system, the power cables should always be connected to the battery. Two options are possible, a basic harness (P/N 115-8000-141) or an implement ready harness (Front Mount: P/N 115-8000-060 and Mid-Mount: P/N 115-8000-315). FIGURE 1.

  • Page 15: Install The Rcm

    INSTALLATION INSTALL THE RCM BEST MOUNTING PRACTICES Ensure the installer follows all of the following guidelines for best mounting practices: • Use the standard RCM mounting bracket (P/N 107-0172-484). • By default, the orientation of the RCM is set to horizontal position with connectors pointing downwards, ensuring that water or moisture will not enter the connectors.
  • Page 16 CHAPTER 3 3. Connect the 23 and 35-pin black connectors from the RCM to ARAG cable (P/N 115-0172-(624, 625, 626)) to the black connectors on the RCM. FIGURE 5. RCM to ARAG Cable Connected 4. Connect the 9-pin ISO connector of RCM Cab ISOBUS Power cable (P/N 115-0172-616) to the 9-pin ISO connector on the in-cab harness.
  • Page 17 8. Connect the RCM in-cab ISOBUS power cable (P/N 115-0172-616) to the COBO power socket. NOTE: For setting the sprayer profile in the RCM module, please refer to the Raven Rate Control Module (RCM) Operation Manual (P/N 016-0171-637). Installation: Install the RCM...

  • Page 18: System Drawings

    CHAPTER 3 SYSTEM DRAWINGS FIGURE 9. RCM ARAG Bravo, 3 Sections, 2-Wire Valve System Drawing (P/N 054-7100-039 Rev. A) FIGURE 10. RCM ARAG Bravo, 5 Sections, 2-Wire Valve System Drawing (P/N 054-7100-040 Rev. A) RCM ARAG Installation Manual...
  • Page 19 INSTALLATION FIGURE 11. RCM ARAG Bravo, 7 Sections, 2-Wire Valve System Drawing (P/N 054-7100-041 Rev. A) FIGURE 12. RCM ARAG Bravo, 6/7 Sections, 3-Wire Valve System Drawing (P/N 054-7100-042 Rev. A) Installation: System Drawings...
  • Page 20 CHAPTER 3 FIGURE 13. RCM ARAG, 3 Sections, 2-Wire Valve w/ CR7 ISO Cable System Drawing (P/N 054-7100-043 Rev. A) FIGURE 14. RCM ARAG, 5 Sections, 2-Wire Valve w/ CR7 ISO Cable System Drawing (P/N 054-7100-044 Rev. A) RCM ARAG Installation Manual...
  • Page 21 INSTALLATION FIGURE 15. RCM ARAG, 7 Sections, 2-Wire Valve w/ CR7 ISO Cable System Drawing (P/N 054-7100-045 Rev. A) FIGURE 16. RCM ARAG, 6/7 Sections, 3-Wire Valve w/ CR7 ISO Cable System Drawing (P/N 054-7100-046 Rev. A) Installation: System Drawings...
  • Page 22 CHAPTER 3 RCM ARAG Installation Manual...
  • Page 23 Index Hydraulic Fittings Introduction Installation Recommendations 5 Point of Reference Updates 016-7100-001 Rev. A...
  • Page 24 Index RCM ARAG Installation Manual...
  • Page 25 Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval. The freight cost to Raven Industries will be the customer’s responsibility.
  • Page 26 Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval. The freight cost to Raven Industries will be the customer’s responsibility.

This manual is also suitable for:

Rcm arag

Table of Contents