Extron electronics System 8 User Manual page 55

-1~). ,:,
;.; ·:r:
PROJECTOR COMMl:JNICATIONS (continued)
BARCO
ELECTROHOME
ECP
ELECTROHOME
MARQUEE
GE/NEC
HUGHES/JVC
MITSUBISHI XC
.. , ·~OtJY
~-
'·ti,·
Note 1:
Note 2:
Note 3:
Note 4:
Note 5:
Note 6:
Note
7:
Note 8:
Note 9:
Note 10:
Note 11:
Note 12:
Note 13:
Note 14:
Note 15:
Note 16:
Note 17:
0
0
0
0
0
0
0
Table 6-2. System Switcher Settings Quick Reference Chart •
2OFF 1 ON
0
2
Short 1 & 2 Short 1 & 2 J2 4
1,3,4ON 2OFF
0 5
3OFF 1 ON
Short 1 &2 Short 1 & 2
J2
5,6,7
1,2,4ON 2OFF
0 5
2,3OFF 1 ON
Short 1 & 2 Short 1 & 2
J2
8, 9, 10,
1,4ON
2OFF
11, 12
0 5
1, 2, 3 OFF
AIIOFF Short2 & 3 Short 1 &2
J3
6, 13, 14
4ON
0 6
1, 3OFF
AIIOFF Short 1 & 2 Short1&2
J2
15
2,4ON
0
0
1, 2 OFF 1 ON
Short 1 & 2 Short 1 & 2 J2 NONE
3,4ON 2OFF
0 0
1, 2 OFF 1 ON
Short 1 & 2 Short 1 & 2 J2 16, 17
3,4ON 2OFF
Initial release 12/3/91 switcher PC Ver. 1.10; compatible with all Ampro software.
The comm adapter must be connected to the switcher before the hand-held remote or the IR
receiver will operate properly.
If the projector is always operated in the executive mode, set SW7 to all OFF. ·
Latest up_date was on 9/9/93 switcher PC Ver. 1.9; compatible with Barco software Ver. 4.0 or
later.'
Initial release 3/2/93 switcher PC Ver. 1.5; compatible with all ECP software Ver. 3:1 only.
The projector will only accept RGBS type signals. For composite or S-Video inputs on the
switcher, you must use a line doubler or decoder when using the VLB feature.
System switchers cannot be looped together when communicating with the ECP projector. The
maximum number of inputs is 10.
Initial release 1/11/94 switcher PC Ver. 2.0; compatible with all Marquee software Ver. 1.9 or
later.
To display composite or S-Video signals, the projector's internal decoder must be installed.
The composite and S-Video outputs of the switcher do not get wired directly to the projector.
Rather, they are wired to the Marquee comm adapter.
When using a System 10 switcher, the projector will read the switcher as two switchers looped
together. Inputs 1-9 will register as switcher 2, inputs 1-9. Input 10 will register as switcher 1,
input 3.
During projector setup, you must enter the Channel List by first pressing "Util. ", then pressing
"2" on the projector remote control. Directions for setting up the Channel List can be found in
the Marquee manual.
Initial release 1/11/94 switcher PC Ver. 2.0; compatible with all GE and NEC software versions.
During projector setup, you must configure the Signal En tty by first pressing "Adjust", then
pressing "1" on the projector remote control. Directions for setting Signal Entty can be found in
the GE
I NEC manual.
Latest release 8/10/93 switcher PC Ver. 1.71; compatible with all Hughes/ JVC software versions.
.Latest release 3/5/93 switcher PC Ver. 1.7; compatible with all Sony software versions.
If you would like the switcher to send the projector a "PAGE" command each time power is
turned on from the switcher, set switch SW4=1.
:I
System 8/10 User's Manual
o
Page 6-5