Related Manuals for Elan Video Over IP
Summary of Contents for Elan Video Over IP
- Page 1 PoE PWR Link EL-4KPM-VIP-TX VIDEO OVER IP CH Select RX TX HDMI IN 24 56V 0 . 5A LINE IN RS-232 VIDEO OVER IP User Manual...
-
Page 2: Table Of Contents
Type 2 Guest Mode - Telnet/IP Conversion To RS-232 parallel proximity to mains power cables. Do not substitute or use any other power supply Manual Configuration (without PC) other than the enclosed unit, or an ELAN approved replacement. EDID Settings Do not disassemble either the Transmitter or Receiver units for any reason. - Page 3 EL-4KPM-VIP-CTRL Enabling TFTP & Telnet EL-4KPM-VIP-CTRL Firmware Update Accessing The Video Over IP Web-GUI Interface Video Over IP Web-GUI - EL-4KPM-VIP-TX 42-45 Video Over IP Web-GUI - EL-4KPM-VIP-RX - Receiver 46-47 Changing Your Computer IP address 48-50 Application Diagrams - Matrix Configuration...
-
Page 4: Introduction
HDMI, IR and RS-232 over standard network architecture. The EL-4KPM-VIP-CTRL Control Module allows simple third party control of the Video over IP system using TCP/IP, RS-232 or IR. The ELAN Video Over IP products can be powered via PoE from a Network switch or locally should the switch not support PoE. -
Page 5: Panel Description - El-4Kpm-Vip-Tx Transmitter
IR RX (IR input) – 3.5mm stereo jack. Transmits IR to any EL-4KPM-VIP-RX receiver currently viewing the EL-4KPM-VIP-TX. Please use supplied ELAN IRR 5V IR Receiver. When using the ELAN IRCAB cable (optional) ensure cable direction is correct IR TX - (IR output) - 3.5mm mono jack – Routed IR from any EL-4KPM-VIP-RX (zone output) allowing source control. Use supplied... -
Page 6: Panel Description - El-4Kpm-Vip-Rx Receiver
IR RX (IR input) – 3.5mm stereo jack. Transmits IR to currently selected EL-4KPM-VIP-TX transmitter allowing routed IR control of sources. Please use supplied ELAN IRR 5V IR Receiver. When using the ELAN IRCAB cable (optional) ensure cable direction is correct. Assignable bi-directional RS-232 port – Connect to third party control device to extend RS-232 commands to any/multiple EL-4KPM-VIP Video Over IP product RS-232 port. -
Page 7: Panel Description - El-4Kpm-Vip-Ctrl Control Module
Control LAN port - Connect to existing network that your third party control system resides on. The Control LAN port is used for Telnet/IP control of the Video Over IP system Video Over IP Video LAN port - Connect to the layer 3 network switch that the ELAN Video Over IP components are connected to Power LED indicator Power port –... -
Page 8: Hdmi Over Ip Network Configuration
IGMP conversation between hosts and routers (Transmitters and Receivers). By listening to this flow of traffic the switch maintains a map of which links need which IP Video Over IP streams. Video Over IPs may be filtered from the links which do not need them and thus controls which ports receive specific Video Over IP traffic. -
Page 9: Understanding Product Status Lights
Power status light - Off = No power, Flashing = Product booting, On = Power on Link status light - Off = No connection to network, Flashing = not connected to any device (another Video Over IP product or network switch), On = Connected to Video Over IP device or network switch... -
Page 10: Infrared Control
Infrared Control The ELAN Video Over IP system can be controlled using local IR hardware connected directly to the EL-4KPM-VIP-RX Receiver. This prevents the need for a third party control solution. Only the source selection feature is available using local IR control through the Receiver. -
Page 11: Infrared Distribution
The ELAN range of Video Over IP products include multiple options for control and routing of IR. Each ELAN Video Over IP Transmitter and Receiver is supplied with both an IR Receiver and Emitter, details below: IR Control Cable - EL-4KACC-IR-CAB Infrared 3.5mm Pin-Out... -
Page 12: Infrared Pass-Through (Source Control)
EL-4KPM-VIP-CTRL/TX/RX USER MANUAL Infrared Pass-Through (Source Control) The Video Over IP products feature Infrared pass-through, allowing users to use original source remote controls in the field and control those sources located in another area. PoE PWR The IR signal is routed to only the current source that is selected, meaning that individual source control can be achieved with... -
Page 13: Serial) Bi-Directional Pass-Through
Type-1 Redirection Mode:- 1-to-1 routed RS-232 A link is programmed that creates an open connection between ANY Video Over IP product in the system (Transmitters or Receivers). Once established the RS-232 commands can be sent in either direction between products. -
Page 14: Type-1 Redirection Mode - 1-To-1 Routed
Type-1 Redirection Mode - 1-to-1 Routed RS-232 The Video Over IP products feature bi-directional RS-232 pass-through for control of products using serial commands from a fixed RX/TX to another. This is also known as Type 1, 1 to 1 routed RS-232 mode. To utilise this you must first enable Type 1 RS-232 mode as follows. - Page 15 You will need to use this MAC Address to create the route RS-232 connection. Next you must send the following messages from the Video Over IP unit you wish to open a connection from. You must enter this command into the 'Console API Command' window (shown on the previous page): 0x0E (0E in hex format) This will put the unit into command mode and you should see a command prompt ">".
- Page 16 Guest Mode - Telnet/IP Conversion To RS-232 The Video Over IP products feature bi-directional RS-232 pass-through for control of products using serial commands from the EL- 4KPM-VIP-CTRL. This is also known as RS-232 Guest Mode. To use this you must first enable Guest Mode as follows.
-
Page 17: Manual Configuration (Without Pc)
Configuring the EL-4KPM-VIP-TX 1) Power the Video Over IP product - To configure the Video Over IP Transmitter first connect the product to a power supply (local or PoE network) and wait for the product to boot up. The front panel LED display will rotate whilst booting and display a 2 digit number when complete. -
Page 18: Edid Settings
In the ELAN Video Over IP system each source device only communicates with a single ELAN EL-4KPM-VIP-TX Transmitter, meaning there is only a single EDID handshake. As each ELAN Video Over IP EL-4KPM-VIP-RX Receiver has its own in-built video scaler, it is advised that the source EDID is set to output the best video signal possible as this can be down-scaled if required at each EL-4KPM- VIP-RX Receiver. -
Page 19: Scaler Output Settings
USER MANUAL Scaler Output Control The ELAN Video Over IP Receiver has an in-built video scaler which can both up-scale and downscale video signals allowing the best picture quality possible at each display. Configuration of Video Over IP Scaler settings can be achieved in several ways:-... -
Page 20: Video Over Ip Pc Program
USER MANUAL Video Over IP PC Program The following pages will review the ELAN Video Over IP PC program and Web GUI interface, giving the installer the knowledge to completely configure a full ELAN HDMI over IP system. Prior to running the ELAN Video Over IP PC configuration software it is important that you have the following hardware available: •... -
Page 21: Firmware Update
3) In order to be able to communicate with the ELAN IP products your computer must also be in the same IP range as the ELAN EL- 4KPM-VIP-TX/RX default IP address. If you are unsure how to update your computer IP range follow the ‘Changing your computer IP address’... -
Page 22: Firmware Update Via Pc Program
EL-4KPM-VIP-CTRL/TX/RX USER MANUAL EL-4KPM-VIP Firmware Update via PC Program To update the firmware in either of the Transmitter or Receiver Video Over IP products using the ELAN PC program please follow the below steps: 1) Open the ELAN PC Program 2) Select the ‘ADVANCED’... -
Page 23: Pc Program Main Menu Overview
USER MANUAL PC Program Main Menu Overview When you first run the ELAN PC Wizard you will see multiple options in the side menu for configuration and control of the Video Over IP system. Transmitter - page shows a summary of all EL-4KPM-VIP-TX (Transmitters) installed, with options for EDID management, checking FW version, updating settings, adding new transmitters, replacing or rebooting products etc. -
Page 24: New Project Configuration
24-56V DC power supply In order to be able to communicate with the ELAN IP products your computer must also be in the same IP range as the ELAN EL- 4KPM-VIP-TX/RX default IP address. If you are unsure how to update your computer IP range follow the ‘Changing your computer IP address’... - Page 25 Receivers After all Transmitter products have been set up the PC wizard will automatically assign an IP address to the Video Over IP Receivers. The first EL-4KPM-VIP-RX Receiver will be given the IP address of 169.254.6.1. The next Receiver will be assigned an IP address of 169.254.6.2 and so on..
- Page 26 Each ELAN Video Over IP products is shipped with the default IP address of 169.254.100.254 Each time the PC wizard looks for a new Video Over IP component to configure it is looking for the default IP address ONLY. It is important that only 1 new ELAN Video Over IP product is connected/configured at a time. Multiple products with the same IP address will cause an IP conflict on the network until configured correctly.
- Page 27 Unable to find new product Should you press ‘CONTINUE’ prior to the Video Over IP product being connected or powered you will see the below warning window. Check the product is powered and connected and click ‘OK’ to try again.
- Page 28 IP address details. For example: Please note: It is not advised that IP address of Video Over IP products be manually confugured as the ELAN EL-4KPM-VIP- CTRL and drivers are configured to the default PC wizard IP address range. Manually assigning IP addresses will prevent the EL-4KPM-VIP-CTRL control module from working.
- Page 29 Once all Transmitter and Receiver products have been configured click ‘FINISH’ which will take you to the Transmitter summary window. It is advised that once basic configuration has been completed you review the additional settings in the Video Over IP products such •...
-
Page 30: Transmitter Summary
5. Status - shows the online / offline status of a product 6. F/W Version - this should marry up with the firmware version that you can find on the ELAN website (see page 21 for more details) 7. EDID - allows you to fix the EDID value for each Transmitter (source) 8. - Page 31 Replacing a Transmitter There may be a time in which an ELAN Video Over IP product has stopped working. Using the summary window the product will show ‘OFFLINE’ in the status window. If after reviewing the faulty product with ELAN Technical Support it is deemed necessary to replace the...
-
Page 32: Receiver Summary
5. Status - shows the online / offline status of a product 6. F/W Version - this should marry up with the firmware version that you can find on the ELAN website (see page 19 for more details) 7. - Page 33 Replacing a Receiver There may be a time in which an ELAN Video Over IP product has stopped working. Using the summary window the product will show ‘OFFLINE’ in the status window. If after reviewing the faulty product with ELAN Technical Support it is deemed necessary to replace the...
-
Page 34: Matrix Control
(Receiver). This page has been designed to allow for the installer to quickly switch the I/O configuration, not for end user control. Once the system has been configured the Matrix Control page will show all online Video Over IP Transmitter and Receiver products. -
Page 35: Video Preview
EL-4KPM-VIP-CTRL/TX/RX USER MANUAL Video Preview The video preview page allows you to view what video signal is passing through all Transmitters and Receivers in the live system. The preview windows are a tool to help diagnose faults with the video distribution system, allowing you to see if each transmitter is receiving a signal from the source, and whether each receiver is transmitting a signal to the display. -
Page 36: Video Wall
Video Wall ELAN Video Over IP receivers can be set up to be part of a video wall array. Each system can contain mulitple video wall arrays of differing sizes. Each video wall can be assigned a number of screens and different layouts that range from 1x2 up to 16x16. -
Page 37: Advanced Settings
To apply this to a Receiver please select the appropriate Receiver from the drop-down box and click ‘Apply’. 2. Firmware update - used to update Video Over IP product firmware. Please see page 19 for further details. 3. Copy EDID - Allows you to copy the EDID from a display connected to a receiver, to a selected transmitter. -
Page 38: System Search
LAN switch at the time of the search. In order for the search function to work you must know the IP address of at least ONE of the Video Over IP products installed. If you have used the PC wizard program then we would advise to use the first product that is configured which is an ELAN EL-4KPM-VIP-TX with the address of 169.254.3.1. -
Page 39: El-4Kpm-Vip-Ctrl Enabling Tftp & Telnet
EL-4KPM-VIP-CTRL/TX/RX USER MANUAL EL-4KPM-VIP-CTRL Enabling TFTP & Telnet Prior to firmware updating the EL-4KPM-VIP-CTRL you must activate both TFTP and Telnet features on your computer. This is achieved using the following steps below:- In Windows, navigate to Start -> Control Panel -> Programs and Features In the Programs and Features screen, select Turn Windows features on or off in the navigation bar on the left. -
Page 40: El-4Kpm-Vip-Ctrl Firmware Update
EL-4KPM-VIP-CTRL/TX/RX USER MANUAL EL-4KPM-VIP-CTRL Firmware Update You may need to update both the Control port and Video port of the EL-4KPM-VIP-CTRL. The process is identical for both ports however your computers IP Address will be different. Follow the below instructions and complete each update separately. -
Page 41: Accessing The Video Over Ip Web-Gui Interface
Once a Video Over IP product has been configured using the PC Wizard program, manual configuration or the Web GUI interface, it will have a different IP address to that of the factory default unit. If you are unsure of the IP address of the Video Over IP product you can press and hold the ‘UP’... -
Page 42: Video Over Ip Web-Gui - El-4Kpm-Vip-Tx
Update Firmware: It may be necessary to update the firmware of the ELAN Video Over IP products. It is advised to check the ELAN website to see if any firmware updates have been uploaded. Download these files and save them to your PC. - Page 43 Network - details information about the connection status of the unit you are communicating directly with (unit ID, IP address, subnet, gateway, MAC address, casting mode (Video Over IP / Unicast), link status and link mode). Changes to the units IP address details can only be viewed from this section, please refer to the Network tab to amend the IP structure of the unit Video - this is the EDID response from the piece of equipment you are connected to.
- Page 44 Unicast and Multicast functionality of the transmitter. Please note: amending the IP address of Video Over IP products will prevent the Video Over IP EL-4KPM-VIP-CTRL control unit from working as this has been configured using default ELAN Video Over IP - IP addresses (169.254.x.x).
- Page 45 To enable RS232 pass through from the transmitter, please use this section to configure the serial settings of your system. Please refer to separate ELAN manual ‘Advanced Video Over IP RS-232 Distribution’ which can be found on the ELAN website.
-
Page 46: Video Over Ip Web-Gui - El-4Kpm-Vip-Rx - Receiver
Network - details information about the connection status of the unit you are communicating directly with (unit ID, IP address, subnet, gateway, MAC address, casting mode (Video Over IP / Unicast), link status and link mode) . Changes to the units IP address details can only be viewed from this section, please refer to the Network tab to amend the IP structure of the unit. - Page 47 Turn Off Screen on Video Lost: Should you not wish for the ELAN Video Over IP logo to be shown when no video signal is sensed then select the adjacent tickbox. This feature may be used for commercial displays that can automatically turn off when no video feed is present.
-
Page 48: Changing Your Computer Ip Address
USER MANUAL Changing Your Computer IP address To communicate with the Control Network or Video Over IP Video Network, you may need to change your IP Address. Connect your computer to your network switch using an Ethernet cable In the Windows toolbar navigate to ‘CONTROL PANEL’... - Page 49 EL-4KPM-VIP-CTRL/TX/RX USER MANUAL In the next window select ‘PROPERTIES’ A. In the ‘NETWORKING’ window highlight/select ‘INTERNET PROTOCOL VERSION 4 (TCP/IPv4)’ B. Select ‘PROPERTIES’, or double click on ‘INTERNET PROTOCOL VERSION 4 (TCP/IPv4)’ www.elanhomesystems.com...
- Page 50 Click ‘OK’ and exit the network setup Enter the default Network Switch or ELAN Video Over IP address in your web browser and check that you can connect to the unit. If you have already configured the Transmitter and Receiver products, enter the address of one of these (it is advised to use 169.254.3.1 which will be the default first Transmitter IP address).
-
Page 51: Application Diagrams - Matrix Configuration
EL-4KPM-VIP-CTRL/TX/RX USER MANUAL www.elanhomesystems.com... -
Page 52: Application Diagrams - Video Wall Configuration
EL-4KPM-VIP-CTRL/TX/RX USER MANUAL contact techsupport@elanhomesystems.com... -
Page 53: Application Diagrams - 1 To 1 Configuration
EL-4KPM-VIP-CTRL/TX/RX USER MANUAL www.elanhomesystems.com... -
Page 54: Application Diagrams - 1 To Many Configuration
EL-4KPM-VIP-CTRL/TX/RX USER MANUAL contact techsupport@elanhomesystems.com... -
Page 55: Terminating The Interconnecting Network Cat Cable
Terminating the interconnecting Network CAT cable It is important that the interconnecting CAT cable between the ELAN Video Over IP products is terminated using the correct RJ45 pin configuration. The link CAT cable MUST be a ‘straight’ (pin-to-pin) CAT cable and it is advised that this is wired to the T568B wiring standard as this format is less prone to EMI (Electro-Magnetic Interference). -
Page 56: Specifications
EL-4KPM-VIP-CTRL/TX/RX USER MANUAL Specifications EL-4KPM-VIP-TX EL-4KPM-VIP-RX • Video input: 1x HDMI type A, female • Video input: 1x LAN RJ45 connector, • Video output: 1x LAN RJ45 connector • Video output: 1x HDMI type A, female • Audio input:1x 3.5mm L/R analogue audio •... -
Page 57: Rs-232 And Telnet Commands
EL-4KPM-VIP-CTRL/TX/RX USER MANUAL RS-232 and Telnet Commands The ELAN Video Over IP system can be controlled via serial and TCP/IP. The following pages list all available serial commands for the Video Over IP solution. Commonly used Serial commands: There are several commands that are commonly used for control and testing:... - Page 58 OUTPUT:xxx HDR ON (xxx:001~762) OUTxxxHDRON Set OUTPUT:xxx HDR ON OUTPUT:xxx HDR OFF (xxx:001~762) OUTxxxHDROFF Set OUTPUT:xxx HDR OFF OUTPUT:xxx STATUS (xxx:001~762) OUTxxxSTATUS Video Over IP IP: xx.xx.xx.xx Channel: xxxx Ethernet Link Status: on/off Video Status: WAITING_HOST_MODE Please Enter command: INPUT:yyy STATUS (yyy:001~762)
-
Page 59: Video Over Ip Infrared Commands
EL-4KPM-VIP-CTRL/TX/RX USER MANUAL Video Over IP Infrared Commands COMMAND NEC IR: CUSTOMER CODE 1898 HEX IR 0000 006D 0000 0022 0157 00AC 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041... - Page 60 EL-4KPM-VIP-CTRL/TX/RX USER MANUAL Video Over IP Infrared Commands COMMAND NEC IR: CUSTOMER CODE 1898 HEX IR 0000 006D 0000 0022 0157 00AC 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041...
- Page 61 EL-4KPM-VIP-CTRL/TX/RX USER MANUAL Video Over IP Infrared Commands COMMAND NEC IR: CUSTOMER CODE 1898 HEX IR 0000 006D 0000 0022 0157 00AC 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041...
- Page 62 EL-4KPM-VIP-CTRL/TX/RX USER MANUAL Video Over IP Infrared Commands COMMAND NEC IR: CUSTOMER CODE 1898 HEX IR 0000 006D 0000 0022 0157 00AC 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041...
- Page 63 EL-4KPM-VIP-CTRL/TX/RX USER MANUAL Video Over IP Infrared Commands COMMAND NEC IR: CUSTOMER CODE 1898 HEX IR 0000 006D 0000 0022 0157 00AC 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041...
- Page 64 EL-4KPM-VIP-CTRL/TX/RX USER MANUAL Video Over IP Infrared Commands COMMAND NEC IR: CUSTOMER CODE 1898 HEX IR 0000 006D 0000 0022 0157 00AC 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041...
- Page 65 EL-4KPM-VIP-CTRL/TX/RX USER MANUAL Video Over IP Infrared Commands COMMAND NEC IR: CUSTOMER CODE 1898 HEX IR 0000 006D 0000 0022 0157 00AC 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041...
- Page 66 EL-4KPM-VIP-CTRL/TX/RX USER MANUAL Video Over IP Infrared Commands COMMAND NEC IR: CUSTOMER CODE 1898 HEX IR 0000 006D 0000 0022 0157 00AC 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041...
- Page 67 EL-4KPM-VIP-CTRL/TX/RX USER MANUAL Video Over IP Infrared Commands COMMAND NEC IR: CUSTOMER CODE 1898 HEX IR 0000 006D 0000 0022 0157 00AC 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041...
- Page 68 EL-4KPM-VIP-CTRL/TX/RX USER MANUAL Video Over IP Infrared Commands COMMAND NEC IR: CUSTOMER CODE 1898 HEX IR 0000 006D 0000 0022 0157 00AC 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041...
- Page 69 EL-4KPM-VIP-CTRL/TX/RX USER MANUAL Video Over IP Infrared Commands COMMAND NEC IR: CUSTOMER CODE 1898 HEX IR 0000 006D 0000 0022 0157 00AC 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041...
- Page 70 EL-4KPM-VIP-CTRL/TX/RX USER MANUAL Video Over IP Infrared Commands COMMAND NEC IR: CUSTOMER CODE 1898 HEX IR 0000 006D 0000 0022 0157 00AC 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041...
- Page 71 EL-4KPM-VIP-CTRL/TX/RX USER MANUAL Video Over IP Infrared Commands COMMAND NEC IR: CUSTOMER CODE 1898 HEX IR 0000 006D 0000 0022 0157 00AC 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041...
- Page 72 EL-4KPM-VIP-CTRL/TX/RX USER MANUAL Video Over IP Infrared Commands COMMAND NEC IR: CUSTOMER CODE 1898 HEX IR 0000 006D 0000 0022 0157 00AC 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041...
- Page 73 EL-4KPM-VIP-CTRL/TX/RX USER MANUAL FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communi- cations.
- Page 74 EL-4KPM-VIP-CTRL/TX/RX USER MANUAL Notes –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– contact techsupport@elanhomesystems.com...
- Page 75 1 (800) 472-5555 - US techsupport@elanhomesystems.com 1 (707) 283-5900 - International 1 (707) 283-5901 - Fax elanhomesystems.com © 2017 ELAN ® is a registered trademark of Core Brands, LLC. 10014820 Rev-D0, 06/2017...