Table of Contents
Advertisement
EL-4KPM-VIP-CTRL/TX/RX
USER MANUAL
Manual Configuration of Video Over IP Products
The ELAN Video Over IP system can be configured without the need of a computer, allowing basic setup options such as addressing of
products (IP configuration), EDID setup and scaler output setup.
Manual configuration does not require the product to be connected to a network switch in order to be set up, they only require the
units to be powered either by local power supply (24-54V 1A) or by a PoE switch/power injector. This means total configuration can
easily be achieved offsite without any network hardware.
Note: Advanced features such as video walls cannot be set up via manual configuration, and requires the PC software.
Configuring the EL-4KPM-VIP-TX
1) Power the Video Over IP product - To configure the Video Over IP Transmitter first connect the product to a power supply (local or
PoE network) and wait for the product to boot up. The front panel LED display will rotate whilst booting and display a 2 digit number
when complete.
2) Put the Video Over IP product into 'Local Configuration' mode - Once the product is powered press both the 'UP' and 'DOWN'
channel buttons on the front panel at the same time for 6 seconds to enter 'Local configuration' mode. You will know that the EL-
4KPM-VIP-TX is in this mode as the LCD front display of the product will show 'LC'.
Lan
PoE PWR
Link
EL-4KPM-VIP-TX
VIDEO OVER IP
CH Select
CH
3) Assign the Transmitter ID (IP address) - Once the product is local configuration mode the display will begin to flash with a lower-
case 't' to indicate that you are about to assign the transmitter identity. The identity will also be the IP address that is automatically
assigned so it is of upmost importance that you do not assign any 2 Video Over IP Transmitter products with the same ID/IP address.
The first ID you should assign is ID1 = 169.254.3.1 (IP address 1)
The second ID you should assign is ID2 = 169.254.3.2 (IP address 2)
And so on....
Once you have selected the ID number press both Channel 'UP' and 'DOWN' buttons at the same time to move on to setting the EDID.
4) Set the EDID - Once the product is in EDID configuration mode the display will begin to flash with a lowercase 'e' to indicate that
you are about to assign an EDID value. Use the 'UP' and 'DOWN' arrows to select the EDID setting required. A full list of EDID settings
can be found on page 18 'EDID Control'.
For example: If the display shows '00' the EDID will be 1080P 2CH.
Once you have selected the EDID required press both Channel 'UP' and 'DOWN' buttons at the same time to finalize the setup. The
Video Over IP product will reboot with the new configuration settings applied.
5) Configuring the EL-4KPM-VIP-RX
Configuring the identity of the EL-4KPM-VIP-RX Receiver is the same steps (steps 1 to 3) as shown above for the configuration of the
EL-4KPM-VIP-TX. When ID has been assigned the Receivers have the following IP addresses:
The first Receiver ID assigned is ID1 = 169.254.6.1 (IP address 1)
The second Receiver ID is ID2 = 169.254.6.2 (IP address 2)
And so on....
6) Set the Video Scaler of the Receiver - Once the product ID has been configured the display will begin to flash with a lowercase 's'
to indicate that you are about to set the scaler output. Use the 'UP' and 'DOWN' arrows to select the scaler setting required. A full list
of scaler settings can be found on page 19 'Scaler Output Control'.
For example: If the display shows '10' the Scaler output will be 4K 30Hz.
Once you have selected the Scaler output required press both Channel 'UP' and 'DOWN' buttons at the same time to finalize the
setup. The Video Over IP product will reboot with the new configuration settings applied.
contact
techsupport@elanhomesystems.com
17
Advertisement
Table of Contents
