Adjusting Attitude (New Cutting Units)
Table 1—New Cutting Unit Set Up Guide
Desired Height-of-Cut
(HOC)
(in)
(mm)
(degrees)
0.375
(10)
0.500
(13)
0.625
(16)
0.750
(19)
0.875
(22)
1.000
(25)
1.125
(29)
1.250
(32)
1.375
(35)
1.500
(38)
1.625
(41)
1.750
(45)
* Optional Low Cut Bedknife, Toro part no. 93-9774, is required for height-of-cut below 0.500" (13 mm).
{ For front ("B") or rear roller distances ("C") less than 1" (25 mm) order long cone nut (Part No. 95-2790) to
replace bottom cone nut for improved support.
Cutting Units
Second Screw
Desired
"A"
Attitude
(Fig. 13)
(in)
(mm)
2*
0.18
4*
0.23
6*
−
8*
−
2*
0.29
4*
0.35
6*
0.41
10.5
8*
−
2
0.22
4
0.28
6
0.34
8
−
2
0.35
4
0.41
10.4
6
0.46
11.9
8
−
2
0.47
12.1
4
0.53
13.6
6
0.59
15.0
8
0.65
16.5
2
0.60
15.3
4
0.66
16.8
6
0.71
18.2
8
0.77
19.7
2
0.72
18.5
4
0.78
19.9
6
0.84
21.4
8
0.90
22.9
2
0.85
21.7
4
0.91
23.1
6
0.96
24.6
8
1.02
26.0
2
0.97
24.8
4
1.03
26.3
6
1.09
27.7
8
1.15
29.2
2
1.10
28.0
4
1.16
29.5
6
1.21
30.9
8
1.27
32.4
2
1.22
31.2
4
1.28
32.6
6
1.34
34.1
8
1.40
35.6
2
−
4
1.41
35.8
6
1.42
36.2
8
1.52
38.7
2
−
4
1.53
39.0
6
1.59
40.4
8
1.65
41.9
Front Height-of-Cut
Rod "B"
(Fig. 14)
(in)
(mm)
4.6
1.62
41.3
5.9
1.82
46.4
−
2.02
54.5
−
−
−
7.6
1.49
38.1
9.0
1.70
43.2
1.90
48.3
−
−
−
5.8
1.36
34.5
7.2
1.56
39.6
8.7
1.76
39.6
−
1.96
49.9
9.0
1.23
31.3
1.43
36.4
1.63
41.6
−
1.83
46.7
1.10
28.2
1.31
33.3
1.51
38.4
1.71
43.5
25.0
0.98{
1.18
30.1
1.38
35.2
1.58
40.3
0.85{
21.8
1.06
26.9
1.26
32.0
1.46
37.2
0.73{
18.6
0.93{
23.7
1.13
28.9
1.38
35.3
0.60{
15.4
0.80{
20.5
1.01
25.7
1.21
30.8
0.48{
12.2
0.68{
17.4
0.88{
22.5
1.08
27.6
0.35{
9.0
0.55{
14.2
0.76{
19.3
0.96{
24.5
−
5.8
0.22{
0.43{
11.0
0.63{
16.2
0.83{
21.3
−
2.6
0.10{
0.30{
7.8
0.51{
13.0
0.71{
18.1
Page 8 - 10
Rear Height-of-Cut
Rear Support
Rod "C"
Bracket
(Fig. 14)
(Fig. 14)
(in)
(mm)
(location)
1.86
47.4
1.62
41.3
1.38
35.2
−
−
1.74
44.2
1.50
38.1
1.26
32.1
−
−
1.91
48.5
1.66
42.4
1.42
26.3
1.19
30.3
1.78
45.3
1.54
29.2
1.30
24.6
1.06
27.1
1.65
42.1
1.41
36.0
1.17
29.9
0.94{
23.9
1.53
38.9
1.29
45.5
1.05
26.8
0.81{
20.7
1.40
35.7
1.16
29.6
0.92{
23.6
0.69{
17.6
1.28
32.6
1.04
26.5
20.4
0.80{
0.56{
14.4
1.15
29.4
0.91{
23.3
17.2
0.67{
0.44{
11.2
1.03
26.2
0.79{
20.1
0.55{
14.0
8.0
0.31{
0.90{
23.0
0.66{
16.9
0.42{
10.9
0.19{
4.9
1.40
35.7
1.16
29.6
0.92{
23.6
0.69{
17.6
1.27
32.5
1.04
26.4
0.80{
20.4
0.56{
14.4
Reelmaster 5500-D
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
top
bottom
bottom
bottom
bottom
bottom
bottom
bottom
bottom