Table of Contents
Advertisement
Chapter 5: Configuration
1=STATUS
1=Loopback DTE
2=TEST
2=Loopback Proto
3=2047 Checker
4=NEBE/FEBE
5=Software Ver
1=Netw. options
ISU 512 ST only
3=CONFIG
2=DTE options
3=Bonding Setup
4=Quick setup
4=DIAL
26
1=Switch type
2=Call type
3=Terminal ID
4=Dial options
1=Dial Line
5=Auto answer
6=Connect Timout
7=Call Screening
8=Passwords
9=Maint Setup
0=Call NumID
2=Leased Line
1=Clock mode
3=S Bus Termination
1=Enabled
2=Channel rate
2=Disabled
3=Test Remote
4=Maint Setup
1=Max Bit Rate
1=64K Mode 1
2=56K Mode 1
1=RS-530
2=Connector Type
2=V.35
3=530-V35 Cable
1=Enable
2=Disable
4=RS366-Y Cable
1=Enable
2=Disable
5=CTS Option
1=Forced CTS
2=Follow RTS
3=Follow CD
4=Off V.25 ANSR
6=CD Options
1=Ignore DTR
2=Idle when Off
7=DTR Options
3=Off > On Dial = 0
4=Dial # 0 if On
5=Answer If On
1=DSR Forced On
8=DSR Options
2=Off Idle + Test
3=Off Link Down
1=TXINT
2=TXFA
1=Dial 512K
3=TXADD01
2=Dial 384K
4=TXDEQ
3=Dial 448K
5=TANULL
4=Dial 336K
6=TCID
5=Video 384K
7=CALL STAGGER
6=Video 336K
7=Leased Slave
8=Leased Master
9=Ldm SlvMstr
ISU 512 User Manual
1=AT&T 5ESS
2= DMS-100
3=National ISDN1
4=NEC Switch
5=EuroISDN (only available on the ISU 512 ST)
1=Speech
2=Audio
3=Data 56Kbps
4=Data 64Kbps
Set SPID
<Use Up and Down keys to select SPID 1 to 8>
Set LDN
<Use Up and Down keys to select LDN 1 to 8>
1=Front Panel
2=RS-366
1=RS366 Time
3=V.25
1=HDLC
2=HDLC(FLAGS)
1=Disabled
2=Enabled
3=Dump all calls
2=Security
1=15 sec
2=30 sec (def)
3=1 minute
4=2 minute
1=Answer any
5=4 minute
2=ansr if SNO...9
1=SPV Password
2=RDL Password
1=Auto Traps
2=ADLP Address
1=Enabled
3=Port Mode
2=Disabled
1=Slave
2=Slave (Master)
3=Master
1=64K Bearer
1=Enabled
2=56K Bearer
2=Disabled
1=Auto Traps
2=ADLP Address
3=Port Mode
1=1x64K
2=2x64K
3=3x64K
1=1x56K
56K
4=4x64K
2=2x56K
112K
5=5x64K
3=3x56K
168K
6=6x64K
4=4x56K
224K
7=7x64K
5=5x56K
280K
8=8x64K
6=6x56K
336K
7=7x56K
392K
8=8x56K
448K
1=CD Forced On
2=Normal
3=Off Link Down
1=Hang up line
2=Dial number
3=Redial last #
4=Answer Call
5=Dial Stored #
6=Store/Review #
Configuration Menu
1=1 sec or EON
2=2 sec or EON
3=5 sec (default)
4=10 sec or EON
5=20 sec or EON
6=Wait for EON
1=Enabled
2=Disabled
64K
128K
192K
256K
320K
384K
448K
512K
Figure 5-1
61202.086L1-1
Advertisement
Table of Contents
