Table of Contents
Advertisement
Quick Links
I
NSTALLATION
P
ORTABLE
Email:sales@challengerlifts.com
Office 800-648-5438
IMPORTANT:
, O
PERATION AND
M
Model MR6
6,000 lbs. Capacity
1500 lb Per Arm
2311 South Park Rd Louisville, Kentucky 40219
/
502-625-0700 Fax 502-587-1933
READ THIS MANUAL COMPLETELY BEFORE
INSTALLING or OPERATING LIFT
M
AINTENANCE
-R
L
ID
ISE
IFT
Web
site:www.challengerlifts.com
M
ANUAL
11/19/2020
Advertisement
Table of Contents
Related Manuals for Challenger Lifts MR6
Summary of Contents for Challenger Lifts MR6
- Page 1 NSTALLATION PERATION AND AINTENANCE ANUAL ORTABLE Model MR6 6,000 lbs. Capacity 1500 lb Per Arm 2311 South Park Rd Louisville, Kentucky 40219 Email:sales@challengerlifts.com site:www.challengerlifts.com Office 800-648-5438 502-625-0700 Fax 502-587-1933 IMPORTANT: READ THIS MANUAL COMPLETELY BEFORE INSTALLING or OPERATING LIFT 11/19/2020...
-
Page 2: General Specifications
Model MR6 Installation, Operation, and Maintenance GENERAL SPECIFICATIONS Maximum Capacity ..................6,000 lbs Minimum Table Height ................5 1/2 inches Maximum Table Height .................. 53 inches Electrical Requirements ............115V, 50/60 Hz, 1 phase Lifting Time ....................45 seconds Safety Lock ………………………………………………System Mechanical Safety Lock Fig. -
Page 3: Safety Notices And Decals
Model MR6 Installation, Operation, and Maintenance Before You Begin Safety decals similar to those shown here are found on a properly installed lift. Be sure that all safety decals have been Safety Notices and Decals correctly installed on the lift. Verify that all... - Page 4 Model MR6 Installation, Operation, and Maintenance Electrical Requirements Receiving For lift installation and operation, it is necessary to The shipment should be thoroughly inspected as have a dedicated 115V single-phase 60-cycle soon as it is received. The signed bill of lading is...
-
Page 5: Installation
Model MR6 Installation, Operation, and Maintenance ELEASE ABLE NSTALLATION 8. Raise the lift until a click is heard; make sure AFETY EQUIREMENTS FOR NSTALLATION AND the lock pawl can pivot freely. ERVICE 9. Look for the threaded tab on the safety lock Refer to ANSI/ALI ALIS (current edition) assembly. -
Page 6: Owner/Employer Responsibilities
Model MR6 Installation, Operation, and Maintenance Owner/Operator Checklist Safety Requirements for Operation, Inspection and Maintenance; and the employer shall insure that SAVE THESE INSTRUCTIONS deliver them to the lift maintenance personnel are qualified and owner/user/employee along with other materials they are adequately trained in the inspection of the furnished with this lift. - Page 7 Model MR6 Installation, Operation, and Maintenance Operating Instructions NOTE: After reviewing these instructions and all decals, get familiar with lift controls by running the lift through a few cycles before loading vehicle on lift. Loading Vehicle Ladder 1. Be sure lift is fully lowered and service bay is clear of all personnel before the vehicle is driven on to lift.
-
Page 8: Lowering Vehicle
Model MR6 Installation, Operation, and Maintenance CAUTION Most specialty or modified vehicles Raising Vehicle cannot be raised on a frame engaging or pad lift. Contact vehicle manufacturer for raising 4. To raise lift: or jacking details. Actuate RAISE switch on electric power unit. -
Page 9: Maintenance
Model MR6 Installation, Operation, and Maintenance MAINTENANCE NOTE: To avoid personal injury, permit only qualified personnel to perform maintenance on this lift. See repair parts breakdown for replacement parts. ALWAYS: Keep all bolts tight. Check periodically. ALWAYS: Keep lift clean. Raise lift when cleaning floor area. -
Page 10: Parts Breakdown
Model MR6 Installation, Operation, and Maintenance ARTS REAKDOWN Description Part # Description Part # Scissor Outside Scissor Pin GTYJ3-01-00 TYJ3-13 Scissor Inside Safety Locking Pin GTYJ3-03-00 TYJ3-08 (Bottom) Platform Safety Locking Pin (Top) GTYJ3-02-00 TYJ3-10 Cylinder Assy. (Left) 16 Locking Nut, M18... - Page 11 Model MR6 Installation, Operation, and Maintenance AFETY SSEMBLY Qty. Description Part # Lock Sheath GTYJ3-07-02CH Lock Pole GTYJ3-07-01 Base TYJ3-07-05 Socket Head Bolt, M8 x 16 MR6-006 Washer, M8 SR-0112 6 GTYJ3-07-04-00CH Pulley Assy. Spring TYJ3-07-06 Lock Block GTYJ3-07-03CH Roll Pin 4 x 30 X10-081 File: MR6-IOM-A.doc...
- Page 12 Model MR6 Installation, Operation, and Maintenance OWER TAND OLLY SSEMBLY NSTRUCTIONS Part # Qty. Description Part # Qty. Description TYJ3-00-01-1 Handle MR6-008 Lock Washer, M8 TYJ3-00-01-2-1 Stand MR6-009 Hex Bolt, M8x25 TYJ3-00-01-2 Base SR-0112 Washer, M8 AB-1563-B Electric/Hyd. Unit HEXNM8...
- Page 13 Model MR6 Installation, Operation, and Maintenance YDRAULIC ELEASE REAKDOWN Part # Qty. Description TYJ3-25 Hydraulic Hose Short GTYJ3-31X Lock Release Cable TYJ3-26 Hydraulic Hose Long 16167 Hyd. Elbow; 9/16-18 O-Ring x 37 deg Male MR6-011 3/8 NPTM x #6 JIC 37 deg Female Swivel TYJ3-21 M14x1.5-6g Male x 3/8 NPT...
- Page 14 Model MR6 Installation, Operation, and Maintenance REVISIONS 11/19/2020- CORRECTED PARTS BREAKDOWN X10-099 TO TYJ3-17 AND TYJ3-07-03CH CORRECTED TO GTYJ3-07-03CH. File: MR6-IOM-A.doc Rev: 11/19/2020...