Low Power-Auto Shutdown 3 Days Enable Lpas 3; Low Power-Auto Shutdown 4 Days Enable Lpas 4; Power Fail Reset Pf Rst; How To Read Power Fail Reset Table - ALLIANCE HWNNE2HP115CW01 Original Instructions Manual

Programming Control
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until LPAS 2 appears in
the display.
4. When LPAS 2 appears in the display, press the START (en-
ter) keypad. The current Low Power/Auto Shutdown 2 Days
Enable status will appear in the display.
on = Option Enabled
oFF = Option Disabled (factory default setting)
5. Press the DELICATES (∧) or the COLD (∨) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Low Power-Auto Shutdown 3 Days
Enable LPAS 3
This option allows the owner to set Low Power/Auto Shutdown
on certain day(s) of the week. Low Power and/or Auto Shutdown
days/duration are programmed using an external device or net-
work.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until LPAS 3 appears in
the display.
4. When LPAS 3 appears in the display, press the START (en-
ter) keypad. The current Low Power/Auto Shutdown 3 Days
Enable status will appear in the display.
on = Option Enabled
oFF = Option Disabled (factory default setting)
5. Press the DELICATES (∧) or the COLD (∨) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Low Power-Auto Shutdown 4 Days
Enable LPAS 4
This option allows the owner to set Low Power/Auto Shutdown
on certain day(s) of the week. Low Power and/or Auto Shutdown
days/duration are programmed using an external device or net-
work.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until LPAS 4 appears in
the display.
4. When LPAS 4 appears in the display, press the START (en-
ter) keypad. The current Low Power/Auto Shutdown 4 Days
Enable status will appear in the display.
on = Option Enabled
oFF = Option Disabled (factory default setting)
5. Press the DELICATES (∧) or the COLD (∨) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.

Power Fail Reset PF rst

This option allows the owner to set the amount of time the con-
trol will store active cycle information in the event of a power
failure. The default setting for Power Fail Reset is OFF. If Power
Fail Reset is turned OFF, the cycle will be saved.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until PF rst appears in
the display.
4. When PF rst appears in the display, press the START (en-
ter) keypad. oFF or a number will appear in the display. This
number corresponds to the current Power Fail Reset setting.
5. Press the DELICATES (∧) or the COLD (∨) keypad to in-
crease or decrease the current number to the desired number
selected from Table 11 .
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.

How to Read Power Fail Reset Table

Use Table 11 to set the amount of time for Power Fail Reset.
oFF turns the option OFF. The current cycle status will be saved.
When power is restored, the cycle will begin where it was inter-
rupted.
Setting this option from 1 - 120 will save the cycle status without
power that number of minutes before the cycle is lost. A value of
0 will cause the cycle and vend to be lost any time a power fail-
ure occurs.
62 Part No. 204370ENR1