Output Setpoint Programming - Electro Cam PLUS PS-5000 Series Programming & Installation Manual

FCN PGM CHN
Programming Error Messages
Flashing error messages indicate programming mistakes
as they occur.
Simply press to cancel flashing error message.
CLR
E1 OLAP: Output pulse just attempted overlapped an existing output
pulse on same channel.
E2 -run: Attempted programming can NOT be done while machine is
running (transducer is turning).
E4 -Pro: Program enable Off when programming was attempted.
E5 8888: Value entered NOT valid for item being programmed.
E6 -379: Invalid setpoint entered: A setpoint ending in 3, 7, or 9 was
entered. (Encoder Only - Exceptions: 89, 179, 269, and 359)
E7 -dEF: Attempted to program too many Enable Inputs (FCN 9).
E9-tdE: Attempted to program too many timed outputs (FCN 5).
E11-ScE: Attempted to program more than 16 speed compensated
outputs (48 I/O controls only).
See pgs. A-12 thru A-14 for more details on error messages.

Output Setpoint Programming

Desired output channel MUST be selected before its
setpoints can be created, viewed, adjusted, or cleared.
SELECT OUTPUT CHANNEL
If POS or RPM
led NOT lit press:
POS
CHN
RPM
POS or RPM CHN and POS
led now lit displays blank
Channel 16 used as example.
VIEW SETPOINTS
View setpoints of output channel presently selected.
VIEW VIEW
ON/OFF setpoints shown in position
display in increasing order with ON
and OFF LEDs. 0 is shown and both
LEDs off if no setpoints exist.
Output Setpoint Programming
POS
1 6
2 Digit value in
1st Digit shown
CHN display
in CHN display
VIEW VIEW
ON/OFF setpoints shown in position
display in decreasing order with ON
and OFF LEDs. 0 is shown and both
LEDs off if no setpoints exist.
4-3 Programming, Standard Features
CREATE SETPOINTS
To create setpoints in output channel presently selected.
3
ON
On led lit, POS 1st Digit shown in
POS display
blank
On at 30 degrees used as example.
6
OFF
OFF led lit, POS 1st Digit shown in
blank POS display
Off at 60 degrees used as example.
Note: When entering multiple pulses, press
pulse.
CHANGE SETPOINTS
To change setpoints in output channel presently selected.
INC/DEC
INC INC
Displayed ON/OFF setpoint increases 1
increment each time INC key is pressed.
NUMERIC ENTRY
5 0
1st Digit shown in 2 Digits shown in
POS display POS display
Changing setpoint to 50 degrees used as example.
PULSE MODE
To change both setpoints of a pulse simultaneously.
PULSE
INC
Pulse led lit ON and OFF setpoints of ALL pulses
increase/decrease 1 increment each
time INC/DEC key is pressed.
MULTI-PULSE MODE
To change all setpoints in the output channel simultaneously.
PULSE PULSE
Pulse led lit
Pulse led
blinking
CLEAR SETPOINTS
CLEAR 1 PULSE
To clear 1 pulse (1 pair of setpoints) on selected output channel.
Use numeric entry method (shown in CHANGE SET-
POINTS above) to set OFF setpoint equal to ON setpoint
value. Both setpoints will be erased.
CLEAR EXISTING SETPOINTS
To clear all setpoints on selected output channel.
ON 0
ON Led lit, 0 shown in
OFF Led
POS blanks POS display
lit, POS
blanks
0
2 Digits shown in
POS display
0
ENT
2 Digits shown in
POS display blinks
POS display
once to confirm
setpoint entry.
ENT
after each
DEC DEC
Displayed ON/OFF setpoint decreases 1
increment each time DEC key is pressed.
ENT
POS display blinks once to
confirm setpoint change.
OR
DEC
OR
INC DEC
ON and OFF setpoints of ALL pulses
increase/decrease 1 increment each
time INC/DEC key is pressed.
OFF 0
ENT
0 shown in POS display
POS blinks and
display shows 0, ON
and OFF LEDs
are off.