Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Humandata XCM-011 Series
Summary of Contents for Humandata XCM-011 Series
- Page 1 Virtex-5 FPGA Board XCM-011 Series User’s Manual HuMANDATA LTD.
-
Page 2: Table Of Contents
Table of Contents Revision History ....................1 Introduction......................1 1. Specifications......................2 2. Overview........................ 3 2.1. Name of Parts ....................3 2.2. Block Diagram ....................4 2.3. Power Supply ..................... 4 2.4. JTAG Connector....................5 3. Configuration Switch..................... 6 4. FPGA Configuration ....................7 5. - Page 3 HuMANDATA will revise the diagram. When a problem can be solved only by replacing components or modifying the product, HuMANDATA will take back the product to replace it with a properly functioning product.
-
Page 4: Revision History
Introduction Thank you for buying our product XCM-011. This is an evaluation board equipped with a Xilinx FPGA Virtex-5, power, reset, and clock circuit and configuration device. It can provide you with very convenient and easy-to-use environment. XCM-011 Series v1.0... -
Page 5: Specifications
Weight 30 [g] typ. User I/O Connectors 66-pin through-hole dia. 0.9 [mm], 100[mil]/2.54 [mm] pitch SIL 7-pin header (Mounted) Accessories 2 DIL 80-pin headers (Cuttable) RoHS Compliance * There may be cases when compatible parts are used. XCM-011 Series v1.0... -
Page 6: Overview
2. Overview 2.1. Name of Parts User I/Os (CNB) Oscillator 48 MHz Power & POR FPGA JTAG User LED User Switch Status LED Config. Switch User I/Os (CNA) Component Side SDRAM Config. Device FRAM Solder Side XCM-011 Series v1.0... -
Page 7: Block Diagram
DC 3.3 V power supply. The external power supply should be sufficient and stabili zed. Notes Please apply power to CNA and CNB with thi ck print pattern or cable. Please connect all ground pins. XCM-011 Series v1.0... -
Page 8: Jtag Connector
This connector is used to configure the FPGA and program the configuration device in-system. Pin assignment is as follows. Pin No. Signal Name Direction VCC (3.3V) OUT (POW) You can use Xilinx download cable. Notice Please pay attention not to attach cables in reverse. XCM-011 Series v1.0... -
Page 9: Configuration Switch
0 = Pull-up during configuration 1 = 3-stated during configuration OFF : 1 5 - 7 : Configuration Mode Configuration Device access : Master SPI FPGA access : JTAG 8 : Suspend Please see the FPGA data sheet for more details. XCM-011 Series v1.0... -
Page 10: Fpga Configuration
9. Select [Part Name] same as which is on the board. 10. Check [Verify] and [Erase Before Programming] in [Device Programming Properties] tab. 11. Select SPI PROM icon, then open [Operation] and click [Program]. Then it will show you the message “Program Succeeded”. XCM-011 Series v1.0... -
Page 11: Configuration Rate
2. Set [Configuration Rate] in [Configuration Options] as [25]. 7. Additional Documentation and User Support The following documents and other supports are available at http://www.hdl.co.jp/en/spc/XCM/xcm-011/ Circuit Schematic Pin List Dimensional drawing PCB drawing Net List … and more. XCM-011 Series v1.0... - Page 12 Virtex-5 FPGA Board XCM-011 Series User’s Manual Ver. 1.0 ..........Jul. 15, 2009 HuMANDATA LTD. Address: 1-2-10-2F, Nakahozumi, Ibaraki Osaka, Japan ZIP 567-0034 Tel: 81-(0)72-620-2002 (Japanese) Fax: 81-(0)72-620-2003 (Japanese/English) URL: http://www.hdl.co.jp/en/ (Global) http://www.hdl.co.jp/ (Japan)